summaryrefslogtreecommitdiff
path: root/recipes/linux/linux-omap-pm-2.6.29/0001-This-merges-Steve-Kipisz-USB-EHCI-support.-He-star.patch
blob: d590f8ffb99c00b597c71af1991d360011339144 (plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
From f8f10f496bce396416d7156da876222c6ce8c341 Mon Sep 17 00:00:00 2001
From: Steven Kipisz <skipisz@beagleboard.org>
Date: Wed, 9 Jan 2009 12:01:11 -0600
Subject: [PATCH-USB] Omap3 beagleboard: add support for EHCI in revision C1 boards

Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
---
 arch/arm/mach-omap2/board-omap3beagle.c |   10 +---------
 arch/arm/mach-omap2/usb-ehci.c          |    4 +---
 drivers/usb/host/ehci-omap.c            |   26 ++++++++++++++++++++++++++
 3 files changed, 28 insertions(+), 12 deletions(-)

diff --git a/arch/arm/mach-omap2/board-omap3beagle.c b/arch/arm/mach-omap2/board-omap3beagle.c
index fe97bab..de81153 100644
--- a/arch/arm/mach-omap2/board-omap3beagle.c
+++ b/arch/arm/mach-omap2/board-omap3beagle.c
@@ -140,15 +140,7 @@ static int beagle_twl_gpio_setup(struct device *dev,
 	 * power switch and overcurrent detect
 	 */
 
-	gpio_request(gpio + 1, "EHCI_nOC");
-	gpio_direction_input(gpio + 1);
-
-	/* TWL4030_GPIO_MAX + 0 == ledA, EHCI nEN_USB_PWR (out, active low) */
-	gpio_request(gpio + TWL4030_GPIO_MAX, "nEN_USB_PWR");
-	gpio_direction_output(gpio + TWL4030_GPIO_MAX, 1);
-
-	/* TWL4030_GPIO_MAX + 1 == ledB, PMU_STAT (out, active low LED) */
-	gpio_leds[2].gpio = gpio + TWL4030_GPIO_MAX + 1;
+        /* TODO: This needs to be modified to not rely on u-boot */
 
 	return 0;
 }
diff --git a/arch/arm/mach-omap2/usb-ehci.c b/arch/arm/mach-omap2/usb-ehci.c
index 489439d..2c6305b 100644
--- a/arch/arm/mach-omap2/usb-ehci.c
+++ b/arch/arm/mach-omap2/usb-ehci.c
@@ -152,9 +152,7 @@ static void setup_ehci_io_mux(void)
 void __init usb_ehci_init(void)
 {
 #if     defined(CONFIG_USB_EHCI_HCD) || defined(CONFIG_USB_EHCI_HCD_MODULE)
-	/* Setup Pin IO MUX for EHCI */
-	if (cpu_is_omap34xx())
-		setup_ehci_io_mux();
+	/* TODO: Setup Pin IO MUX for EHCI - moved this temporarily to U-boot */
 
 	if (platform_device_register(&ehci_device) < 0) {
 		printk(KERN_ERR "Unable to register HS-USB (EHCI) device\n");

diff --git a/drivers/usb/host/ehci-omap.c b/drivers/usb/host/ehci-omap.c
index 1b3266c..8472996 100644
--- a/drivers/usb/host/ehci-omap.c
+++ b/drivers/usb/host/ehci-omap.c
@@ -48,16 +48,26 @@
  *		to get the PHY state machine in working state
  */
 #define EXTERNAL_PHY_RESET
+#ifdef CONFIG_MACH_OMAP3_BEAGLE
+#define	EXT_PHY_RESET_GPIO_PORT2	(147)
+#else
 #define	EXT_PHY_RESET_GPIO_PORT1	(57)
 #define	EXT_PHY_RESET_GPIO_PORT2	(61)
+#endif
 #define	EXT_PHY_RESET_DELAY		(10)
 
+#define PHY_STP_PULLUP_ENABLE           (0x10)
+#define PHY_STP_PULLUP_DISABLE          (0x90)
+
+
 /* ISSUE2:
  * USBHOST supports External charge pump PHYs only
  * Use the VBUS from Port1 to power VBUS of Port2 externally
  * So use Port2 as the working ULPI port
  */
+#ifndef CONFIG_MACH_OMAP3_BEAGLE
 #define VBUS_INTERNAL_CHARGEPUMP_HACK
+#endif
 
 #endif /* CONFIG_OMAP_EHCI_PHY_MODE */
 
@@ -225,14 +235,43 @@ static int omap_start_ehc(struct platform_device *dev, struct usb_hcd *hcd)
 
 #ifdef EXTERNAL_PHY_RESET
 	/* Refer: ISSUE1 */
+#ifndef CONFIG_MACH_OMAP3_BEAGLE
 	gpio_request(EXT_PHY_RESET_GPIO_PORT1, "USB1 PHY reset");
 	gpio_direction_output(EXT_PHY_RESET_GPIO_PORT1, 0);
+#endif
 	gpio_request(EXT_PHY_RESET_GPIO_PORT2, "USB2 PHY reset");
 	gpio_direction_output(EXT_PHY_RESET_GPIO_PORT2, 0);
+	gpio_set_value(EXT_PHY_RESET_GPIO_PORT2, 0);
 	/* Hold the PHY in RESET for enough time till DIR is high */
 	udelay(EXT_PHY_RESET_DELAY);
 #endif
 
+        /*
+         * The PHY register 0x7 - Interface Control register is
+         * configured to disable the integrated STP pull-up resistor
+         * used for interface protection.
+	 *
+	 * May not need to be here.
+         */
+        omap_writel((0x7 << EHCI_INSNREG05_ULPI_REGADD_SHIFT) |/* interface reg */
+                (2 << EHCI_INSNREG05_ULPI_OPSEL_SHIFT) |/*   Write */
+                (1 << EHCI_INSNREG05_ULPI_PORTSEL_SHIFT) |/* Port1 */
+                (1 << EHCI_INSNREG05_ULPI_CONTROL_SHIFT) |/* Start */
+                (PHY_STP_PULLUP_DISABLE),
+                EHCI_INSNREG05_ULPI);
+
+        while (!(omap_readl(EHCI_INSNREG05_ULPI) & (1<<EHCI_INSNREG05_ULPI_CONTROL_SHIFT)));
+
+        /* Force PHY to HS */
+        omap_writel((0x4 << EHCI_INSNREG05_ULPI_REGADD_SHIFT) |/* function ctrl */
+                (2 << EHCI_INSNREG05_ULPI_OPSEL_SHIFT) |/*   Write */
+                (1 << EHCI_INSNREG05_ULPI_PORTSEL_SHIFT) |/* Port1 */
+                (1 << EHCI_INSNREG05_ULPI_CONTROL_SHIFT) |/* Start */
+                (0x40),
+                EHCI_INSNREG05_ULPI);
+
+        while (!(omap_readl(EHCI_INSNREG05_ULPI) & (1<<EHCI_INSNREG05_ULPI_CONTROL_SHIFT)));
+
 	/* Configure TLL for 60Mhz clk for ULPI */
 	ehci_clocks->usbtll_fck_clk = clk_get(&dev->dev, USBHOST_TLL_FCLK);
 	if (IS_ERR(ehci_clocks->usbtll_fck_clk))
@@ -307,7 +346,9 @@ static int omap_start_ehc(struct platform_device *dev, struct usb_hcd *hcd)
 	 * Hold the PHY in RESET for enough time till PHY is settled and ready
 	 */
 	udelay(EXT_PHY_RESET_DELAY);
+#ifndef CONFIG_MACH_OMAP3_BEAGLE
 	gpio_set_value(EXT_PHY_RESET_GPIO_PORT1, 1);
+#endif
 	gpio_set_value(EXT_PHY_RESET_GPIO_PORT2, 1);
 #endif
 
@@ -393,7 +434,9 @@ static void omap_stop_ehc(struct platform_device *dev, struct usb_hcd *hcd)
 
 
 #ifdef EXTERNAL_PHY_RESET
+#ifndef CONFIG_MACH_OMAP3_BEAGLE
 	gpio_free(EXT_PHY_RESET_GPIO_PORT1);
+#endif
 	gpio_free(EXT_PHY_RESET_GPIO_PORT2);
 #endif

--
1.6.0.4.790.gaa14a