1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
|
#!/bin/sh
# This script is run once when the system first boots. Its sole
# purpose is to create /etc/default/sysconf (the overall system
# configuration file) and other files derived from this.
#
# The script runs immediately after S10checkroot.sh - this is the
# point at which the rootfs will be mounted rw even if the kernel
# booted with it ro.
#
# rm or mv the file to run this again. If this is done the
# following configuration files will be rewritten:
#
# /etc/default/sysconf
# /etc/hostname
# /etc/defaultdomain
# /etc/network/interfaces
# /etc/resolv.conf
#
test -r /etc/default/sysconf && exit 0
#
# /etc/default/functions contains useful utility functions - it's
# in a separate file so that it can be loaded by any script
. /etc/default/functions
#
# Utility to deal with absence of DNS configuration
echodns(){
local dns
if test $# -gt 0
then
for dns in "$@"
do
echo "nameserver $dns"
done
fi
}
#
# The SysConf device must exist in /dev at this point for this script
# to work.
#
# It is important not to hard-wire the name of the device because of
# the posibility of changing the flash partition layout.
#
# The block device is used here because at present udev does not
# show the character devices
sysdev="$(mtblockdev SysConf)"
if test -n "$sysdev" -a -b "$sysdev"
then
# Read the defined part of SysConf into /etc/default/sysconf.
# SysConf has lines of two forms:
#
# [section]
# name=value
#
# In practice SysConf also contains other stuff, use the command:
#
# devio '<</dev/mtd1;cpb'
#
# to examine the current settings. The badly formatted stuff
# is removed (to be exact, the sed script selects only lines
# which match one of the two above). The lan interface, which
# defaults to ixp0, is changed to the correct value for openslug,
# eth0
devio '<<'"$sysdev"';cpb;fb1,10' | sed -n '/^\[[^][]*\]$/p;
s/^lan_interface=ixp0$/lan_interface=eth0/;
/^[-a-zA-Z0-9_][-a-zA-Z0-9_]*=/p' >/etc/default/sysconf
#
# Now take the result and set up the 'standard' files in the
# root file system (these couldn't be set up before because
# they depend on stuff which RedBoot puts into SysConf from the
# ID info on the specific machine - in particular the hardware
# address of eth0, which must be the one assigned for *this*
# box!)
#
# HOSTNAME: defaults to LGK<mac> i.e. something derived from
# the ethernet hardware. LinkSys documentation explains how
# to determine this. Set by the user in linksys setup software.
# DOMAINNAME: LinkSys puts this in w_d_name.
test -n "$(config host)" && config host >/etc/hostname
domain="$(config domain)"
test -n "$domain" && echo "$domain" >/etc/defaultdomain
#
# Ethernet information. This goes into /etc/network/interfaces,
# however this is only used for static setup (and this is not
# the default). With dhcp the openslug udhcp script,
# /etc/udhcpc.d/50default, loads the values from sysconf. The
# lan_interface config value must exist for the file to be
# overwritten here.
iface="$(config iface)"
if test -n "$iface"
then
boot="$(config boot)"
# Only dhcp and static are supported at present - bootp
# support requires installation of appropriate packages
# dhcp is the fail-safe
case "$boot" in
dhcp|static) ;;
*) boot=dhcp;;
esac
#
mac="$(config mac)"
ip="$(config ip)"
netmask="$(config netmask)"
gateway="$(config gateway)"
{
echo "# /etc/network/interfaces"
echo "# configuration file for ifup(8), ifdown(8)"
echo "#"
echo "# The loopback interface"
echo "auto lo"
echo "iface lo inet loopback"
echo "#"
echo "# The NSLU2 built-in ethernet"
echo "auto eth0"
echo "# Automatically generated from /etc/default/sysconf"
if test -n "$mac"
then
echo "# The pre-up option must always be supplied, regardless"
echo "# of configuration, to set the hardware correctly."
echo "# Severe network problems may result if this option is"
echo "# removed."
c=
else
echo "# WARNING: improperly configured network interface."
echo "# WARNING: the pre-up line must be corrected or severe"
echo "# WARNING: network problems may result."
c='#'
mac='<WARNING: unknown hardware address>'
fi
echo "iface $iface inet $boot"
echo "${c} pre-up ifconfig $iface hw ether $mac"
# The following are ignored for DHCP but are harmless
test -n "$ip" && echo " address $ip"
test -n "$netmask" && echo " netmask $netmask"
test -n "$gateway" && echo " gateway $gateway"
} >/etc/network/interfaces
fi
#
# The DNS server information gives up to three nameservers, but this
# currently only binds in the first.
{
test -n "$domain" && echo "search $domain"
echodns $(config dns) $(config dns1) $(config dns2)
} >/etc/resolv.conf
fi
exit 0
|
