1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
|
/*
* arch/arm/mach-ixp4xx/nas100d-setup.c
*
* NAS 100d board-setup
*
* based ixdp425-setup.c:
* Copyright (C) 2003-2004 MontaVista Software, Inc.
*
* Author: Mark Rakes <mrakes at mac.com>
* Maintainers: http://www.nslu2-linux.org/
*
*/
#include <linux/kernel.h>
#include <linux/serial.h>
#include <linux/serial_8250.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/mach/flash.h>
static struct flash_platform_data nas100d_flash_data = {
.map_name = "cfi_probe",
.width = 2,
};
static struct resource nas100d_flash_resource = {
.start = NAS100D_FLASH_BASE,
.end = NAS100D_FLASH_BASE + NAS100D_FLASH_SIZE,
.flags = IORESOURCE_MEM,
};
static struct platform_device nas100d_flash = {
.name = "IXP4XX-Flash",
.id = 0,
.dev.platform_data = &nas100d_flash_data,
.num_resources = 1,
.resource = &nas100d_flash_resource,
};
static struct ixp4xx_i2c_pins nas100d_i2c_gpio_pins = {
.sda_pin = NAS100D_SDA_PIN,
.scl_pin = NAS100D_SCL_PIN,
};
static struct platform_device nas100d_i2c_controller = {
.name = "IXP4XX-I2C",
.id = 0,
.dev.platform_data = &nas100d_i2c_gpio_pins,
.num_resources = 0,
};
static struct resource nas100d_uart_resources[] = {
{
.start = IXP4XX_UART1_BASE_PHYS,
.end = IXP4XX_UART1_BASE_PHYS + 0x0fff,
.flags = IORESOURCE_MEM,
},
{
.start = IXP4XX_UART2_BASE_PHYS,
.end = IXP4XX_UART2_BASE_PHYS + 0x0fff,
.flags = IORESOURCE_MEM,
}
};
static struct plat_serial8250_port nas100d_uart_data[] = {
{
.mapbase = IXP4XX_UART1_BASE_PHYS,
.membase = (char *)IXP4XX_UART1_BASE_VIRT + REG_OFFSET,
.irq = IRQ_IXP4XX_UART1,
.flags = UPF_BOOT_AUTOCONF,
.iotype = UPIO_MEM,
.regshift = 2,
.uartclk = IXP4XX_UART_XTAL,
},
{
.mapbase = IXP4XX_UART2_BASE_PHYS,
.membase = (char *)IXP4XX_UART2_BASE_VIRT + REG_OFFSET,
.irq = IRQ_IXP4XX_UART2,
.flags = UPF_BOOT_AUTOCONF,
.iotype = UPIO_MEM,
.regshift = 2,
.uartclk = IXP4XX_UART_XTAL,
},
{ }
};
static struct platform_device nas100d_uart = {
.name = "serial8250",
.id = PLAT8250_DEV_PLATFORM,
.dev.platform_data = nas100d_uart_data,
.num_resources = 2,
.resource = nas100d_uart_resources,
};
static struct platform_device *nas100d_devices[] __initdata = {
&nas100d_i2c_controller,
&nas100d_flash,
&nas100d_uart,
};
static void nas100d_power_off(void)
{
/* This causes the box to drop the power and go dead. */
/* enable the pwr cntl gpio */
gpio_line_config(NAS100D_PO_GPIO, IXP4XX_GPIO_OUT);
/* do the deed */
gpio_line_set(NAS100D_PO_GPIO, IXP4XX_GPIO_HIGH);
}
static void __init nas100d_init(void)
{
ixp4xx_sys_init();
pm_power_off = nas100d_power_off;
platform_add_devices(nas100d_devices, ARRAY_SIZE(nas100d_devices));
}
MACHINE_START(NAS100D, "Iomega NAS 100d")
/* Maintainer: www.nslu2-linux.org */
.phys_ram = PHYS_OFFSET,
.phys_io = IXP4XX_PERIPHERAL_BASE_PHYS,
.io_pg_offst = ((IXP4XX_PERIPHERAL_BASE_VIRT) >> 18) & 0xFFFC,
.boot_params = 0x00000100,
.map_io = ixp4xx_map_io,
.init_irq = ixp4xx_init_irq,
.timer = &ixp4xx_timer,
.init_machine = nas100d_init,
MACHINE_END
|
