summaryrefslogtreecommitdiff
path: root/packages/linux/linux-2.6.18/atmel-usart3-driver.patch
blob: 2f1b1cf13730c849ecd567ec44c77e9623a5f893 (plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
342
343
344
345
346
347
348
349
350
351
352
353
354
355
356
357
358
359
360
361
362
363
364
365
366
367
368
369
370
371
372
373
374
375
376
377
378
379
380
381
382
383
384
385
386
387
388
389
390
391
392
393
394
395
396
397
398
399
400
401
402
403
404
405
406
407
408
409
410
411
412
413
414
415
416
417
418
419
420
421
422
423
424
425
426
427
428
429
430
431
432
433
434
435
436
437
438
439
440
441
442
443
444
445
446
447
448
449
450
451
452
453
454
455
456
457
458
459
460
461
462
463
464
465
466
467
468
469
470
471
472
473
474
475
476
477
478
479
480
481
482
483
484
485
486
487
488
489
490
491
492
493
494
495
496
497
498
499
500
501
502
503
504
505
506
507
508
509
510
511
512
513
514
515
516
517
518
519
520
521
522
523
524
525
526
527
528
529
530
531
532
533
534
535
536
537
538
539
540
541
542
543
544
545
546
547
548
549
550
551
552
553
554
555
556
557
558
559
560
561
562
563
564
565
566
567
568
569
570
571
572
573
574
575
576
577
578
579
580
581
582
583
584
585
586
587
588
589
590
591
592
593
594
595
596
597
598
599
600
601
602
603
604
605
606
607
608
609
610
611
612
613
614
615
616
617
618
619
620
621
622
623
624
625
626
627
628
629
630
631
632
633
634
635
636
637
638
639
640
641
642
643
644
645
646
647
648
649
650
651
652
653
654
655
656
657
658
659
660
661
662
663
664
665
666
667
668
669
670
671
672
673
674
675
676
677
678
679
680
681
682
683
684
685
686
687
688
689
690
691
692
693
694
695
696
697
698
699
700
701
702
703
704
705
706
707
708
709
710
711
712
713
714
715
716
717
718
719
720
721
722
723
724
725
726
727
728
729
730
731
732
733
734
735
736
737
738
739
740
741
742
743
744
745
746
747
748
749
750
751
752
753
754
755
756
757
758
759
760
761
762
763
764
765
766
767
768
769
770
771
772
773
774
775
776
777
778
779
780
781
782
783
784
785
786
787
788
789
790
791
792
793
794
795
796
797
798
799
800
801
802
803
804
805
806
807
808
809
810
811
812
813
814
815
816
817
818
819
820
821
822
823
824
825
826
827
828
829
830
831
832
833
834
835
836
837
838
839
840
841
842
843
844
845
846
847
848
849
850
851
852
853
854
855
856
857
858
859
860
861
862
863
864
865
866
867
868
869
870
871
872
873
874
875
876
877
878
879
880
881
882
883
884
885
886
887
888
889
890
891
892
893
894
895
896
897
898
899
900
901
902
903
904
905
906
907
908
909
910
911
912
913
914
915
916
917
918
919
920
921
922
923
924
925
926
927
928
929
930
931
932
933
934
935
936
937
938
939
940
941
942
943
944
945
946
947
948
949
950
951
952
953
954
955
956
957
958
959
960
961
962
963
964
965
966
967
968
969
970
971
972
973
974
975
976
977
978
979
980
981
982
983
984
985
986
987
988
989
990
991
992
993
994
995
996
997
998
999
1000
1001
1002
1003
1004
1005
1006
1007
1008
1009
1010
1011
1012
1013
1014
1015
1016
1017
1018
1019
1020
1021
1022
1023
1024
1025
1026
1027
1028
1029
1030
1031
1032
1033
1034
1035
1036
1037
1038
1039
1040
1041
1042
1043
1044
1045
1046
1047
1048
1049
1050
1051
1052
1053
1054
1055
1056
1057
1058
1059
1060
1061
1062
1063
1064
1065
1066
1067
1068
1069
1070
1071
1072
1073
1074
1075
1076
1077
1078
1079
1080
1081
1082
1083
1084
1085
1086
1087
1088
1089
1090
1091
1092
1093
1094
1095
1096
1097
1098
1099
1100
1101
1102
1103
1104
1105
1106
1107
1108
1109
1110
1111
1112
1113
1114
1115
1116
1117
1118
1119
1120
1121
1122
1123
1124
1125
1126
1127
1128
1129
1130
1131
1132
1133
1134
1135
1136
1137
1138
1139
1140
1141
1142
1143
1144
1145
1146
1147
1148
1149
1150
1151
1152
1153
1154
1155
1156
1157
1158
1159
1160
1161
1162
1163
1164
1165
1166
1167
1168
1169
1170
1171
1172
1173
1174
1175
1176
1177
1178
1179
1180
1181
1182
1183
1184
1185
1186
1187
1188
1189
1190
1191
1192
1193
1194
1195
1196
1197
1198
1199
1200
1201
1202
1203
1204
1205
1206
1207
1208
1209
1210
1211
1212
1213
1214
1215
1216
1217
1218
1219
1220
1221
1222
1223
1224
1225
1226
1227
1228
1229
1230
1231
1232
1233
1234
1235
1236
1237
1238
1239
1240
1241
1242
1243
1244
1245
1246
1247
1248
1249
1250
1251
1252
1253
1254
1255
1256
1257
1258
1259
1260
1261
1262
1263
1264
1265
1266
1267
1268
1269
1270
1271
1272
1273
1274
1275
1276
1277
1278
1279
1280
1281
1282
1283
1284
1285
1286
1287
1288
1289
1290
1291
1292
1293
1294
1295
1296
1297
1298
1299
1300
1301
1302
1303
1304
1305
1306
1307
1308
1309
1310
1311
1312
1313
1314
1315
1316
1317
1318
1319
1320
1321
1322
1323
1324
1325
1326
1327
1328
1329
1330
1331
1332
1333
1334
1335
1336
1337
1338
1339
1340
1341
1342
1343
1344
1345
1346
1347
1348
1349
1350
1351
1352
1353
1354
1355
1356
1357
1358
1359
1360
1361
1362
1363
1364
1365
1366
1367
1368
1369
1370
1371
1372
1373
1374
1375
1376
1377
1378
1379
1380
1381
1382
1383
1384
1385
1386
1387
1388
1389
1390
1391
1392
1393
1394
1395
1396
1397
1398
1399
1400
1401
1402
1403
1404
1405
1406
1407
1408
1409
1410
1411
1412
1413
1414
1415
1416
1417
1418
1419
1420
1421
1422
1423
1424
1425
1426
1427
1428
1429
1430
1431
1432
1433
1434
1435
1436
1437
1438
1439
1440
1441
1442
1443
From nobody Mon Sep 17 00:00:00 2001
From: Håvard Skinnemoen <hskinnemoen@atmel.com>
Date: Fri Nov 18 16:31:34 2005 +0100
Subject: [PATCH] AVR32: USART3 Serial Driver

---

 drivers/serial/Kconfig       |   21 
 drivers/serial/Makefile      |    1 
 drivers/serial/atmel_usart.c | 1086 +++++++++++++++++++++++++++++++++++++++++++
 drivers/serial/atmel_usart.h |  290 +++++++++++
 4 files changed, 1398 insertions(+)

Index: linux-2.6.18-avr32/drivers/serial/Kconfig
===================================================================
--- linux-2.6.18-avr32.orig/drivers/serial/Kconfig	2006-11-02 14:16:07.000000000 +0100
+++ linux-2.6.18-avr32/drivers/serial/Kconfig	2006-11-02 15:54:18.000000000 +0100
@@ -246,6 +246,27 @@ config SERIAL_8250_AU1X00
 
 comment "Non-8250 serial port support"
 
+config SERIAL_ATMEL
+	tristate "Atmel USART3 serial port support"
+	depends on AVR32
+	select SERIAL_CORE
+	default y
+	help
+	  Support for the Atmel USART3 on-chip USART found in most
+	  AT32 and AT91 parts from Atmel.
+
+	  If unsure, say Y.
+
+config SERIAL_ATMEL_CONSOLE
+	bool "Support for console on Atmel USART3 serial port"
+	depends on SERIAL_ATMEL=y
+	select SERIAL_CORE_CONSOLE
+	help
+	  Say Y here if you wish to use an Atmel USART3 serial port as
+	  the system console (the system console is the device which
+	  receives all kernel messages and warnings and which allows
+	  logins in single user mode).
+
 config SERIAL_AMBA_PL010
 	tristate "ARM AMBA PL010 serial port support"
 	depends on ARM_AMBA && (BROKEN || !ARCH_VERSATILE)
Index: linux-2.6.18-avr32/drivers/serial/Makefile
===================================================================
--- linux-2.6.18-avr32.orig/drivers/serial/Makefile	2006-11-02 14:16:07.000000000 +0100
+++ linux-2.6.18-avr32/drivers/serial/Makefile	2006-11-02 14:17:29.000000000 +0100
@@ -20,6 +20,7 @@ obj-$(CONFIG_SERIAL_8250_BOCA) += 8250_b
 obj-$(CONFIG_SERIAL_8250_HUB6) += 8250_hub6.o
 obj-$(CONFIG_SERIAL_8250_MCA) += 8250_mca.o
 obj-$(CONFIG_SERIAL_8250_AU1X00) += 8250_au1x00.o
+obj-$(CONFIG_SERIAL_ATMEL) += atmel_usart.o
 obj-$(CONFIG_SERIAL_AMBA_PL010) += amba-pl010.o
 obj-$(CONFIG_SERIAL_AMBA_PL011) += amba-pl011.o
 obj-$(CONFIG_SERIAL_CLPS711X) += clps711x.o
Index: linux-2.6.18-avr32/drivers/serial/atmel_usart.c
===================================================================
--- /dev/null	1970-01-01 00:00:00.000000000 +0000
+++ linux-2.6.18-avr32/drivers/serial/atmel_usart.c	2006-11-02 15:54:18.000000000 +0100
@@ -0,0 +1,1086 @@
+/*
+ * Driver for Atmel USART3 Serial ports
+ *
+ * Based on AT91RM9200 serial driver by Rick Bronson
+ * Based on drivers/char/serial.c, by Linus Torvalds, Theodore Ts'o.
+ * Based on drivers/serial/sa1100.c by Deep Blue Solutions Ltd.
+ *
+ * Copyright (C) 2004-2006 Atmel Corporation
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+#include <linux/clk.h>
+#include <linux/console.h>
+#include <linux/dma-mapping.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/ioport.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/sched.h>
+#include <linux/serial.h>
+#include <linux/tty.h>
+
+#include <asm/io.h>
+#include <asm/irq.h>
+
+#include <asm/arch/board.h>
+
+#if defined(CONFIG_SERIAL_ATMEL_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ)
+#define SUPPORT_SYSRQ
+#include <linux/sysrq.h>
+#endif
+
+#include <linux/serial_core.h>
+
+#include "atmel_usart.h"
+
+/*
+ * TODO: Move this definition into linux/serial_core.h
+ */
+#define PORT_USART3		60
+
+/*
+ * Use the same major/minor numbers as the AT91 USART, which is
+ * actually the same chip
+ */
+#define SERIAL_USART3_MAJOR	TTY_MAJOR
+#define MINOR_START		64
+#define NR_PORTS		4
+
+#define ERROR_FLAGS		(USART3_BIT(CSR_PARE)		\
+				 | USART3_BIT(CSR_FRAME)	\
+				 | USART3_BIT(CSR_OVRE))
+
+/* Must be a power of two, or everything will break */
+#define RX_BUFFER_SIZE		32
+struct usart3_port {
+	void __iomem *regs;
+	int break_active;
+	unsigned int tx_dma_head;
+	int rx_tail;
+	char *rx_buffer;
+	dma_addr_t rx_dma;
+	dma_addr_t tx_dma;
+	struct clk *mck;
+	unsigned long mapsize;
+	struct uart_port uart;
+};
+#define to_usart3_port(port) container_of(port, struct usart3_port, uart)
+
+static void tx_dma_sync(struct uart_port *port)
+{
+	struct usart3_port *up = to_usart3_port(port);
+	struct circ_buf *xmit = &port->info->xmit;
+
+	if (xmit->head < up->tx_dma_head) {
+		dma_sync_single_for_device(port->dev,
+					   up->tx_dma + up->tx_dma_head,
+					   UART_XMIT_SIZE - up->tx_dma_head,
+					   DMA_TO_DEVICE);
+		dma_sync_single_for_device(port->dev, up->tx_dma,
+					   xmit->head, DMA_TO_DEVICE);
+	} else {
+		dma_sync_single_for_device(port->dev,
+					   up->tx_dma + up->tx_dma_head,
+					   xmit->head - up->tx_dma_head,
+					   DMA_TO_DEVICE);
+	}
+}
+
+static void tx_dma_update_tail(struct uart_port *port)
+{
+	struct usart3_port *up = to_usart3_port(port);
+	struct circ_buf *xmit = &port->info->xmit;
+	unsigned long status, remaining;
+	unsigned int new_tail;
+
+	/* Account for the characters DMA'ed since last update */
+	remaining = usart3_readl(up, TCR);
+
+	if (up->tx_dma_head < xmit->tail) {
+		/*
+		 * We have wrapped around, and there's a chunk at the
+		 * beginning of the buffer that has been submitted for
+		 * DMA.  If the ENDTX bit is set, it means that the
+		 * DMA controller also has wrapped around and copied
+		 * TNPR/TNCR into TPR/TCR.
+		 */
+		status = usart3_readl(up, CSR);
+		BUG_ON((up->tx_dma_head != 0)
+		       && (usart3_readl(up, TNCR) == 0)
+		       && !(status & USART3_BIT(ENDTX)));
+		if (status & USART3_BIT(ENDTX)) {
+			BUG_ON(usart3_readl(up, TNCR) != 0);
+
+			/* The ENDTX bit might be set after we read TCR */
+			remaining = usart3_readl(up, TCR);
+
+			usart3_writel(up, TNCR, 0);
+			port->icount.tx += UART_XMIT_SIZE - xmit->tail;
+			xmit->tail = 0;
+
+			BUG_ON(remaining > up->tx_dma_head);
+			new_tail = up->tx_dma_head - remaining;
+		} else {
+			/*
+			 * The DMA controller hasn't switched yet, so
+			 * TCR indicates the number of bytes left
+			 * until this happens.
+			 */
+			new_tail = UART_XMIT_SIZE - remaining;
+		}
+	} else {
+		/* No wraparound, move the tail closer to dma_head. */
+		BUG_ON(remaining > up->tx_dma_head);
+		new_tail = up->tx_dma_head - remaining;
+	}
+
+	BUG_ON(new_tail < xmit->tail);
+	port->icount.tx += new_tail - xmit->tail;
+	xmit->tail = new_tail;
+}
+
+static inline void tx_dma_start(struct usart3_port *up)
+{
+	/* Start the PDC and enable interrupts */
+	usart3_writel(up, PTCR, USART3_BIT(TXTEN));
+	usart3_writel(up, IER, USART3_BIT(ENDTX));
+}
+
+static inline void tx_dma_stop(struct usart3_port *up)
+{
+	usart3_writel(up, PTCR, USART3_BIT(TXTDIS));
+	usart3_writel(up, IDR, USART3_BIT(ENDTX));
+}
+
+static inline unsigned int rx_dma_get_head(struct usart3_port *up)
+{
+	unsigned int head;
+	u32 status;
+
+	head = RX_BUFFER_SIZE - usart3_readl(up, RCR);
+	status = usart3_readl(up, CSR);
+	if (status & USART3_BIT(ENDRX))
+		head = RX_BUFFER_SIZE;
+
+	return head;
+}
+
+static inline int rx_dma_update_tail(struct usart3_port *up,
+				     unsigned int tail)
+{
+	int again = 0;
+
+	if (!(tail & (RX_BUFFER_SIZE - 1))) {
+		u32 rnpr = up->rx_dma;
+
+		tail &= RX_BUFFER_SIZE;
+		if (!tail)
+			rnpr += RX_BUFFER_SIZE;
+
+		usart3_writel(up, RNPR, rnpr);
+		usart3_writel(up, RNCR, RX_BUFFER_SIZE);
+
+		again = 1;
+	} else
+		BUG_ON(usart3_readl(up, CSR) & USART3_BIT(ENDRX));
+
+	up->rx_tail = tail;
+
+	return again;
+}
+
+static void usart3_stop_tx(struct uart_port *port)
+{
+	struct usart3_port *up = to_usart3_port(port);
+
+	tx_dma_stop(up);
+	tx_dma_update_tail(port);
+}
+
+static void usart3_start_tx(struct uart_port *port)
+{
+	struct usart3_port *up = to_usart3_port(port);
+	struct circ_buf *xmit = &port->info->xmit;
+
+	BUG_ON(!irqs_disabled());
+
+	/*
+	 * Stop the DMA engine so that we don't have to worry about race
+	 * conditions when updating the various pointers and counters.
+	 */
+	tx_dma_stop(up);
+
+	tx_dma_sync(port);
+	tx_dma_update_tail(port);
+
+	if (uart_circ_empty(xmit))
+		return;
+
+	usart3_writel(up, TPR, up->tx_dma + xmit->tail);
+
+	if (xmit->head > xmit->tail) {
+		usart3_writel(up, TCR, xmit->head - xmit->tail);
+	} else {
+		usart3_writel(up, TCR, UART_XMIT_SIZE - xmit->tail);
+		usart3_writel(up, TNPR, up->tx_dma);
+		usart3_writel(up, TNCR, xmit->head);
+	}
+
+	/* Keep track of what we've submitted for DMA */
+	up->tx_dma_head = xmit->head;
+
+	/* Resume operation of DMA engine. */
+	tx_dma_start(up);
+}
+
+static void usart3_stop_rx(struct uart_port *port)
+{
+	struct usart3_port *up = to_usart3_port(port);
+
+	pr_debug("usart3: stop_rx\n");
+
+	usart3_writel(up, PTCR, USART3_BIT(RXTDIS));
+	usart3_writel(up, IDR, (USART3_BIT(TIMEOUT)
+				| USART3_BIT(ENDRX)
+				| USART3_BIT(RXBRK)
+				| USART3_BIT(OVRE)
+				| USART3_BIT(FRAME)
+				| USART3_BIT(PARE)));
+}
+
+static void usart3_flush_buffer(struct uart_port *port)
+{
+	struct usart3_port *up = to_usart3_port(port);
+
+	/*
+	 * Reset TX DMA state. Note that we must _always_ update TNCR
+	 * before TCR, since the value in TNCR will automatically move
+	 * to TCR when TCR is 0.
+	 */
+	usart3_writel(up, TNCR, 0);
+	usart3_writel(up, TCR, 0);
+	up->tx_dma_head = port->info->xmit.tail;
+}
+
+/*
+ * Enable modem status interrupts
+ */
+static void usart3_enable_ms(struct uart_port *port)
+{
+	struct usart3_port *up = to_usart3_port(port);
+
+	pr_debug("usart3: enable_ms\n");
+	usart3_writel(up, IER, (USART3_BIT(RIIC)
+				| USART3_BIT(DSRIC)
+				| USART3_BIT(DCDIC)
+				| USART3_BIT(CTSIC)));
+}
+
+static inline void handle_rx_error(struct uart_port *port, u32 status)
+{
+	/*
+	 * FIXME: Errors should affect the flag buffer, but due to the
+	 * PDC, we don't really know which char they belong to...
+	 */
+	if (status & USART3_BIT(PARE)) {
+		printk(KERN_NOTICE "usart%u: Parity error\n", port->line);
+		port->icount.parity++;
+	} else if (status & USART3_BIT(FRAME)) {
+		printk(KERN_NOTICE "usart%u: Frame error\n", port->line);
+		port->icount.frame++;
+	}
+	if (status & USART3_BIT(OVRE)) {
+		printk(KERN_NOTICE "usart%u: Overrun\n", port->line);
+		port->icount.overrun++;
+	}
+
+#ifdef SUPPORT_SYSRQ
+	port->sysrq = 0;
+#endif
+}
+
+static inline void handle_pdc_endtx(struct uart_port *port, unsigned long status)
+{
+	struct usart3_port *up = to_usart3_port(port);
+	struct circ_buf *xmit = &port->info->xmit;
+
+	tx_dma_update_tail(port);
+
+	if (uart_tx_stopped(port)) {
+		usart3_stop_tx(port);
+		printk("usart3: stopped\n");
+		return;
+	}
+
+	if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
+		uart_write_wakeup(port);
+
+	if (uart_circ_empty(xmit))
+		usart3_stop_tx(port);
+
+	/*
+	 * It could be that xmit is being updated right now. If so,
+	 * start_tx() will be called shortly.
+	 */
+	if (status & USART3_BIT(TXBUFE))
+		usart3_writel(up, IDR, USART3_BIT(ENDTX));
+}
+
+static void consume_rx_buffer(struct uart_port *port, struct pt_regs *regs)
+{
+	struct usart3_port *up = to_usart3_port(port);
+	struct tty_struct *tty = port->info->tty;
+	unsigned long head, tail;
+	int len;
+	int again;
+
+	do {
+		/*
+		 * Re-arm the timeout before we decide how many
+		 * characters to read.
+		 */
+		usart3_writel(up, CR, USART3_BIT(STTTO));
+
+		head = rx_dma_get_head(up);
+
+		tail = up->rx_tail;
+		if (tail & RX_BUFFER_SIZE)
+			head += RX_BUFFER_SIZE;
+
+		if (head == tail)
+			break;
+
+		dma_sync_single_for_cpu(port->dev, up->rx_dma + tail,
+					head - tail, DMA_FROM_DEVICE);
+
+		if (uart_handle_sysrq_char(port, up->rx_buffer[tail],
+					   regs)) {
+			tail++;
+			if (head == tail)
+				goto update_tail;
+		}
+
+		len = tty_insert_flip_string(tty, up->rx_buffer + tail,
+					     head - tail);
+		port->icount.rx += len;
+		tail += len;
+		if (!(head & (RX_BUFFER_SIZE - 1)) && tail != head) {
+			/*
+			 * head has wrapped, but there isn't enough
+			 * room in the buffer to handle all the
+			 * characters.  We must recycle this buffer in
+			 * order to clear the interrupt.
+			 */
+			tty_insert_flip_char(tty, 0, TTY_OVERRUN);
+			tail = head;
+		}
+
+	update_tail:
+		again = rx_dma_update_tail(up, tail);
+	} while (again);
+
+	tty_flip_buffer_push(tty);
+}
+
+/*
+ * This is the serial driver's interrupt routine
+ */
+static irqreturn_t usart3_interrupt(int irq, void *dev_id,
+				    struct pt_regs *regs)
+{
+	struct uart_port *port = dev_id;
+	struct usart3_port *up = to_usart3_port(port);
+	u32 status, mask, pending;
+	irqreturn_t ret = IRQ_NONE;
+
+	spin_lock(&port->lock);
+
+	status = usart3_readl(up, CSR);
+	mask = usart3_readl(up, IMR);
+	pending = status & mask;
+	if (unlikely(!pending))
+		goto out;
+
+	ret = IRQ_HANDLED;
+
+	do {
+		/*
+		 * Consume the buffer and flip buffers if necessary.
+		 */
+		consume_rx_buffer(port, regs);
+
+		/* Clear any break and error flags */
+		usart3_writel(up, CR, USART3_BIT(RSTSTA));
+
+		if (pending & (USART3_BIT(OVRE)
+			       | USART3_BIT(FRAME)
+			       | USART3_BIT(PARE)))
+			handle_rx_error(port, status);
+
+		if (pending & USART3_BIT(RXBRK)) {
+			if (up->break_active) {
+				up->break_active = 0;
+			} else {
+				up->break_active = 1;
+				port->icount.brk++;
+				uart_handle_break(port);
+			}
+		}
+
+		if (pending & USART3_BIT(RIIC))
+			port->icount.rng++;
+		if (pending & USART3_BIT(DSRIC))
+			port->icount.dsr++;
+		if (pending & USART3_BIT(DCDIC)) {
+			port->icount.dcd++;
+			uart_handle_dcd_change
+				(port, status & USART3_BIT(DCD));
+		}
+		if (pending & USART3_BIT(CTSIC)) {
+			port->icount.cts++;
+			uart_handle_cts_change
+				(port, status & USART3_BIT(CTS));
+		}
+		if (pending & (USART3_BIT(RIIC)
+			       | USART3_BIT(DSRIC)
+			       | USART3_BIT(DCDIC)
+			       | USART3_BIT(CTSIC)))
+			wake_up_interruptible(&port->info->delta_msr_wait);
+
+		if (pending & USART3_BIT(ENDTX))
+			handle_pdc_endtx(port, status);
+
+		status = usart3_readl(up, CSR);
+		pending = status & usart3_readl(up, IMR);
+	} while (pending);
+
+out:
+	spin_unlock(&port->lock);
+	return ret;
+}
+
+/*
+ * Return TIOCSER_TEMT when transmitter is not busy
+ */
+static unsigned int usart3_tx_empty(struct uart_port *port)
+{
+	struct usart3_port *up = to_usart3_port(port);
+	unsigned int ret = 0;
+
+	if (usart3_readl(up, CSR) & USART3_BIT(TXEMPTY))
+		ret = TIOCSER_TEMT;
+
+	pr_debug("usart3: tx_empty returned %x\n", ret);
+
+	return ret;
+}
+
+static unsigned int usart3_get_mctrl(struct uart_port *port)
+{
+	struct usart3_port *up = to_usart3_port(port);
+	unsigned int ret = 0;
+	unsigned int status;
+
+	status = usart3_readl(up, CSR);
+	if (status & USART3_BIT(DCD))
+		ret |= TIOCM_CD;
+	if (status & USART3_BIT(CTS))
+		ret |= TIOCM_CTS;
+	if (status & USART3_BIT(DSR))
+		ret |= TIOCM_DSR;
+	if (status & USART3_BIT(RI))
+		ret |= TIOCM_RI;
+
+	pr_debug("usart3: get_mctrl returned %x\n", ret);
+
+	return ret;
+}
+
+static void usart3_set_mctrl(struct uart_port *port, unsigned int mctrl)
+{
+	struct usart3_port *up = to_usart3_port(port);
+	unsigned int control = 0;
+
+	pr_debug("usart3: set_mctrl %x\n", mctrl);
+
+	if (mctrl & TIOCM_RTS)
+		control |= USART3_BIT(RTSEN);
+	else
+		control |= USART3_BIT(RTSDIS);
+
+	if (mctrl & TIOCM_DTR)
+		control |= USART3_BIT(DTREN);
+	else
+		control |= USART3_BIT(DTRDIS);
+
+	usart3_writel(up, CR, control);
+}
+
+static void usart3_break_ctl(struct uart_port *port, int break_state)
+{
+	struct usart3_port *up = to_usart3_port(port);
+
+	pr_debug("usart3: break_ctl %u\n", break_state);
+	if (break_state != 0)
+		usart3_writel(up, CR, USART3_BIT(STTBRK));
+	else
+		usart3_writel(up, CR, USART3_BIT(STPBRK));
+}
+
+static int usart3_startup(struct uart_port *port)
+{
+	struct usart3_port *up = to_usart3_port(port);
+	int ret;
+
+	pr_debug("usart3: startup\n");
+
+	up->break_active = 0;
+
+	/* Set up interrupt handler */
+	ret = request_irq(port->irq, usart3_interrupt, 0,
+			  port->info->tty->name, port);
+	if (ret) {
+		printk(KERN_ERR "usart3: Unable to request irq %d\n",
+		       port->irq);
+		return ret;
+	}
+
+	up->rx_dma = dma_map_single(port->dev, up->rx_buffer,
+				    2 * RX_BUFFER_SIZE, DMA_FROM_DEVICE);
+	up->tx_dma = dma_map_single(port->dev, port->info->xmit.buf,
+				    UART_XMIT_SIZE, DMA_TO_DEVICE);
+
+	/* Initialize the PDC for RX (TX is done in start_tx) */
+	up->rx_tail = 0;
+	usart3_writel(up, RPR, up->rx_dma);
+	usart3_writel(up, RCR, RX_BUFFER_SIZE);
+	usart3_writel(up, RNPR, up->rx_dma + RX_BUFFER_SIZE);
+	usart3_writel(up, RNCR, RX_BUFFER_SIZE);
+	usart3_writel(up, PTCR, USART3_BIT(RXTEN));
+
+	/* Reset DMA state */
+	usart3_writel(up, TNCR, 0);
+	usart3_writel(up, TCR, 0);
+	up->tx_dma_head = port->info->xmit.tail;
+
+	/*
+	 * Set a suitable timeout. 2000 bit periods corresponds to
+	 * about 17 ms at 115200 bps
+	 */
+	usart3_writel(up, RTOR, 2000);
+
+	/* Reset and enable receiver and transmitter */
+	usart3_writel(up, CR, (USART3_BIT(RSTRX)
+				  | USART3_BIT(RSTTX)
+				  | USART3_BIT(RSTSTA)));
+	usart3_writel(up, CR, (USART3_BIT(RXEN)
+				  | USART3_BIT(TXEN)));
+
+	/* Enable timeout, end of rx, break and error interrupts */
+	usart3_writel(up, IER, (USART3_BIT(TIMEOUT)
+				   | USART3_BIT(ENDRX)
+				   | USART3_BIT(RXBRK)
+				   | USART3_BIT(OVRE)
+				   | USART3_BIT(FRAME)
+				   | USART3_BIT(PARE)));
+
+	/* Arm the timeout counter */
+	usart3_writel(up, CR, USART3_BIT(STTTO));
+
+	return 0;
+}
+
+static void usart3_shutdown(struct uart_port *port)
+{
+	struct usart3_port *up = to_usart3_port(port);
+
+	pr_debug("usart3: shutdown\n");
+
+	/* Disable all interrupts and reset any error flags */
+	usart3_writel(up, IDR, -1L);
+	usart3_writel(up, CR, USART3_BIT(RSTSTA));
+
+	dma_unmap_single(port->dev, up->rx_dma, 2 * RX_BUFFER_SIZE,
+			 DMA_FROM_DEVICE);
+	dma_unmap_single(port->dev, up->tx_dma, UART_XMIT_SIZE,
+			 DMA_TO_DEVICE);
+
+	free_irq(port->irq, port);
+}
+
+static void usart3_set_termios(struct uart_port *port, struct termios *termios,
+			       struct termios *old)
+{
+	struct usart3_port *up = to_usart3_port(port);
+	unsigned int baud, quot, mode = 0;
+	unsigned int imr, flags;
+
+	pr_debug("usart3: set_termios\n");
+
+	switch (termios->c_cflag & CSIZE) {
+	case CS5:
+		mode |= USART3_BF(CHRL, USART3_CHRL_5);
+		break;
+	case CS6:
+		mode |= USART3_BF(CHRL, USART3_CHRL_6);
+		break;
+	case CS7:
+		mode |= USART3_BF(CHRL, USART3_CHRL_7);
+		break;
+	default:
+		mode |= USART3_BF(CHRL, USART3_CHRL_8);
+		break;
+	}
+
+	if (termios->c_cflag & CSTOPB)
+		mode |= USART3_BF(NBSTOP, USART3_NBSTOP_2);
+
+	if (termios->c_cflag & PARENB) {
+		 if (termios->c_cflag & PARODD)
+			 mode |= USART3_BF(PAR, USART3_PAR_ODD);
+		 else
+			 mode |= USART3_BF(PAR, USART3_PAR_EVEN);
+	} else {
+		mode |= USART3_BF(PAR, USART3_PAR_NONE);
+	}
+
+	/*
+	 * Ask the core to calculate the divisor for us.
+	 */
+	baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk / 16);
+	quot = uart_get_divisor(port, baud);
+
+	/* Bits to ignore, timeout, etc. TBD */
+
+	/*
+	 * Save and disable interrupts
+	 */
+	spin_lock_irqsave(&port->lock, flags);
+	imr = usart3_readl(up, IMR);
+	usart3_writel(up, IDR, -1L);
+	spin_unlock_irqrestore(&port->lock, flags);
+
+	/*
+	 * Make sure transmitter is empty. If BRGR == 0, it is safest
+	 * to do a reset, since waiting for the transmitter to be
+	 * empty will take forever.
+	 */
+	if (usart3_readl(up, BRGR) != 0) {
+		while (!(usart3_readl(up, CSR) & USART3_BIT(TXRDY)))
+			barrier();
+	} else {
+		usart3_writel(up, CR, (USART3_BIT(RSTTX)
+					  | USART3_BIT(RSTRX)));
+	}
+
+	pr_debug("usart3: Setting BRGR to %u (baud rate %u)...\n", quot, baud);
+
+	/* Disable receiver and transmitter */
+	usart3_writel(up, CR, (USART3_BIT(TXDIS)
+				  | USART3_BIT(RXDIS)));
+
+	/* Set the parity, stop bits and data size */
+	usart3_writel(up, MR, mode);
+
+	/* Set the baud rate and enable receiver and transmitter */
+	usart3_writel(up, BRGR, quot);
+	usart3_writel(up, CR, (USART3_BIT(TXEN)
+				  | USART3_BIT(RXEN)));
+
+	/* Restore interrupts */
+	usart3_writel(up, IER, imr);
+}
+
+static const char *usart3_type(struct uart_port *port)
+{
+	return "USART3";
+}
+
+static void usart3_release_port(struct uart_port *port)
+{
+	pr_debug("usart3: release_port\n");
+	iounmap(port->membase);
+	port->flags |= UPF_IOREMAP;
+}
+
+static int usart3_request_port(struct uart_port *port)
+{
+	struct usart3_port *up = to_usart3_port(port);
+
+	/* TODO: remove this */
+	pr_debug("usart3: request_port\n");
+	if (port->flags & UPF_IOREMAP) {
+		port->membase = ioremap(port->mapbase, up->mapsize);
+		up->regs = port->membase;
+		port->flags &= ~UPF_IOREMAP;
+	}
+	return 0;
+}
+
+static void usart3_config_port(struct uart_port *port, int flags)
+{
+	pr_debug("usart3: config_port\n");
+	if (flags & UART_CONFIG_TYPE) {
+		if (usart3_request_port(port) == 0)
+			port->type = PORT_USART3;
+	}
+}
+
+static int usart3_verify_port(struct uart_port *port, struct serial_struct *ser)
+{
+	int ret = 0;
+
+	if (ser->type != PORT_UNKNOWN && ser->type != PORT_USART3)
+		ret = -EINVAL;
+	if (port->irq != ser->irq)
+		ret = -EINVAL;
+	if (ser->io_type != SERIAL_IO_MEM)
+		ret = -EINVAL;
+	if (port->uartclk / 16 != ser->baud_base)
+		ret = -EINVAL;
+	if ((void *)port->mapbase != ser->iomem_base)
+		ret = -EINVAL;
+	if (ser->hub6 != 0)
+		ret = -EINVAL;
+
+	pr_debug("usart3_verify_port returned %d\n", ret);
+
+	return ret;
+}
+
+static struct uart_ops usart3_pops = {
+	.tx_empty	= usart3_tx_empty,
+	.set_mctrl	= usart3_set_mctrl,
+	.get_mctrl	= usart3_get_mctrl,
+	.stop_tx	= usart3_stop_tx,
+	.start_tx	= usart3_start_tx,
+	.stop_rx	= usart3_stop_rx,
+	.enable_ms	= usart3_enable_ms,
+	.break_ctl	= usart3_break_ctl,
+	.startup	= usart3_startup,
+	.shutdown	= usart3_shutdown,
+	.flush_buffer	= usart3_flush_buffer,
+	.set_termios	= usart3_set_termios,
+	.type		= usart3_type,
+	.release_port	= usart3_release_port,
+	.request_port	= usart3_request_port,
+	.config_port	= usart3_config_port,
+	.verify_port	= usart3_verify_port,
+};
+
+static int __devinit initialize_port(struct usart3_port *up,
+				      struct platform_device *pdev)
+{
+	struct uart_port *port = &up->uart;
+	struct resource *regs;
+
+	regs = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	if (!regs)
+		return -ENXIO;
+
+	spin_lock_init(&port->lock);
+
+	up->mck = clk_get(&pdev->dev, "usart");
+	if (IS_ERR(up->mck))
+		return PTR_ERR(up->mck);
+	clk_enable(up->mck);
+
+	port->mapbase = regs->start;
+	up->mapsize = regs->end - regs->start + 1;
+	port->irq = platform_get_irq(pdev, 0);
+
+	port->uartclk = clk_get_rate(up->mck);
+	port->iotype = SERIAL_IO_MEM;
+	port->flags = UPF_BOOT_AUTOCONF | UPF_IOREMAP;
+	port->ops = &usart3_pops;
+	port->line = pdev->id;
+	port->dev = &pdev->dev;
+
+	return 0;
+}
+
+static struct usart3_port usart3_ports[NR_PORTS];
+
+#ifdef CONFIG_SERIAL_ATMEL_CONSOLE
+
+static void usart3_console_write(struct console *console, const char *string,
+				 unsigned int len)
+{
+	struct usart3_port *up = &usart3_ports[console->index];
+	unsigned int imr, i;
+	unsigned long flags, ptsr;
+
+	/*
+	 * Save IMR, then disable interrupts
+	 */
+	local_irq_save(flags);
+	imr = usart3_readl(up, IMR);
+	usart3_writel(up, IDR, ~0UL);
+	local_irq_restore(flags);
+
+	/*
+	 * Save PDC state and disable PDC transmission
+	 */
+	ptsr = usart3_readl(up, PTSR);
+	usart3_writel(up, PTCR, USART3_BIT(TXTDIS));
+
+	/*
+	 * Now, do each character
+	 */
+	for (i = 0; i < len; i++, string++) {
+		char c = *string;
+
+		/*
+		 * If we're sending LF, send CR first...
+		 */
+		if (c == '\n') {
+			while (!(usart3_readl(up, CSR)
+				 & USART3_BIT(TXRDY)))
+				;
+			usart3_writel(up, THR, '\r');
+		}
+		while (!(usart3_readl(up, CSR) & USART3_BIT(TXRDY)))
+			;
+		usart3_writel(up, THR, c);
+	}
+
+	/*
+	 * Wait for transmitter to become empty and restore the IMR
+	 * and PDC state.
+	 */
+	while (!(usart3_readl(up, CSR) & USART3_BIT(TXRDY)))
+		;
+
+	usart3_writel(up, PTCR, ptsr & USART3_BIT(TXTEN));
+	usart3_writel(up, IER, imr);
+}
+
+static int __init usart3_console_setup(struct console *console,
+				       char *options)
+{
+	struct platform_device *pdev;
+	struct usart3_port *up;
+	struct uart_port *port;
+	int baud = 115200;
+	int bits = 8;
+	int parity = 'n';
+	int flow = 'n';
+	int ret;
+
+	if (console->index >= NR_PORTS) {
+		printk(KERN_ERR
+		       "Can't use USART%u for console: index >= NR_PORTS\n",
+		       console->index);
+		return -ENODEV;
+	}
+
+	pdev = at91_default_console_device;
+	if (!pdev)
+		return -ENXIO;
+
+	up = &usart3_ports[console->index];
+	port = &up->uart;
+
+	ret = initialize_port(up, pdev);
+	if (ret)
+		return ret;
+
+	port->membase = ioremap(port->mapbase, up->mapsize);
+	ret = -ENOMEM;
+	if (!port->membase)
+		goto out_disable_clk;
+
+	up->regs = port->membase;
+
+	/* Set a fixed baud rate for now */
+	usart3_writel(up, BRGR, 2);
+
+	/* Make sure all interrupts are disabled and reset/enable the USART */
+	usart3_writel(up, IDR, -1L);
+	usart3_writel(up, CR, (USART3_BIT(RSTRX)
+				  | USART3_BIT(RSTTX)
+				  | USART3_BIT(RSTSTA)));
+	usart3_writel(up, CR, (USART3_BIT(RXEN)
+				  | USART3_BIT(TXEN)));
+
+	if (options)
+		uart_parse_options(options, &baud, &parity, &bits, &flow);
+
+	return uart_set_options(port, console, baud, parity, bits, flow);
+
+out_disable_clk:
+	clk_disable(up->mck);
+	clk_put(up->mck);
+	return ret;
+}
+
+static struct uart_driver usart3_reg;
+static struct console usart3_console = {
+	.name		= "ttyUS",
+	.write		= usart3_console_write,
+	.device		= uart_console_device,
+	.setup		= usart3_console_setup,
+	.flags		= CON_PRINTBUFFER,
+	.index		= -1,
+	.data		= &usart3_reg,
+};
+
+static int __init usart3_console_init(void)
+{
+	register_console(&usart3_console);
+	return 0;
+}
+console_initcall(usart3_console_init);
+
+#define USART3_CONSOLE &usart3_console
+
+#else
+#define USART3_CONSOLE NULL
+#endif
+
+static struct uart_driver usart3_reg = {
+	.owner		= THIS_MODULE,
+	.driver_name	= "serial",
+	.dev_name	= "ttyUS",
+	.major		= SERIAL_USART3_MAJOR,
+	.minor		= MINOR_START,
+	.nr		= NR_PORTS,
+	.cons		= USART3_CONSOLE,
+};
+
+static int usart3_serial_suspend(struct platform_device *pdev,
+				 pm_message_t state)
+{
+	struct usart3_port *port = platform_get_drvdata(pdev);
+	int retval = 0;
+
+	if (port)
+		retval = uart_suspend_port(&usart3_reg, &port->uart);
+
+	return retval;
+}
+
+static int usart3_serial_resume(struct platform_device *pdev)
+{
+	struct usart3_port *port = platform_get_drvdata(pdev);
+	int retval = 0;
+
+	if (port)
+		retval = uart_resume_port(&usart3_reg, &port->uart);
+
+	return retval;
+}
+
+static int __devinit usart3_serial_probe(struct platform_device *pdev)
+{
+	struct usart3_port *up;
+	int ret;
+
+	if (pdev->id >= NR_PORTS) {
+		printk(KERN_WARNING
+		       "Ignoring USART%u, as NR_PORTS is only %u\n",
+		       pdev->id, NR_PORTS);
+		return -ENOMEM;
+	}
+
+	up = &usart3_ports[pdev->id];
+
+	/*
+	 * If the port has already been set up as a console, we
+	 * shouldn't enable it again.
+	 */
+	if (!up->uart.uartclk) {
+		ret = initialize_port(up, pdev);
+		if (ret)
+			goto out;
+	}
+
+	/*
+	 * The RX buffer must be cacheline aligned. If it's not,
+	 * invalidating the cache could be disastrous...
+	 *
+	 * Fortunately, kmalloc() always returns cache-aligned memory.
+	 */
+	ret = -ENOMEM;
+	up->rx_buffer = kmalloc(2 * RX_BUFFER_SIZE, GFP_KERNEL);
+	if (!up->rx_buffer)
+		goto out_disable_clk;
+
+	ret = uart_add_one_port(&usart3_reg, &up->uart);
+	if (ret)
+		goto out_free_rx_buffer;
+
+	platform_set_drvdata(pdev, up);
+
+	return 0;
+
+out_free_rx_buffer:
+	kfree(up->rx_buffer);
+out_disable_clk:
+	clk_disable(up->mck);
+	clk_put(up->mck);
+out:
+	return ret;
+}
+
+static int __devexit usart3_serial_remove(struct platform_device *pdev)
+{
+	struct usart3_port *port = platform_get_drvdata(pdev);
+	int retval = 0;
+
+	platform_set_drvdata(pdev, NULL);
+
+	if (port) {
+		retval = uart_remove_one_port(&usart3_reg, &port->uart);
+		clk_disable(port->mck);
+		clk_put(port->mck);
+		kfree(port->rx_buffer);
+		kfree(port);
+	}
+
+	return retval;
+}
+
+static struct platform_driver usart3_serial_driver = {
+	.probe		= usart3_serial_probe,
+	.remove		= __devexit_p(usart3_serial_remove),
+	.suspend	= usart3_serial_suspend,
+	.resume		= usart3_serial_resume,
+	.driver		= {
+		.name	= "usart",
+	},
+};
+
+static int __init usart3_init(void)
+{
+	int ret;
+
+	printk(KERN_INFO "Serial: Atmel USART3 driver\n");
+
+	ret = uart_register_driver(&usart3_reg);
+	if (ret)
+		return ret;
+
+	ret = platform_driver_register(&usart3_serial_driver);
+	if (ret)
+		uart_unregister_driver(&usart3_reg);
+
+	return ret;
+}
+
+static void __exit usart3_exit(void)
+{
+	platform_driver_unregister(&usart3_serial_driver);
+	uart_unregister_driver(&usart3_reg);
+}
+
+module_init(usart3_init);
+module_exit(usart3_exit);
+
+MODULE_LICENSE("GPL");
+MODULE_DESCRIPTION("Atmel USART3 serial driver");
+MODULE_AUTHOR("Haavard Skinnemoen <hskinnemoen@atmel.com>");
Index: linux-2.6.18-avr32/drivers/serial/atmel_usart.h
===================================================================
--- /dev/null	1970-01-01 00:00:00.000000000 +0000
+++ linux-2.6.18-avr32/drivers/serial/atmel_usart.h	2006-11-02 16:37:02.000000000 +0100
@@ -0,0 +1,290 @@
+/*
+ * Register definitions for USART3
+ *
+ * Copyright (C) 2005-2006 Atmel Corporation
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+#ifndef __ASM_AVR32_USART3_H__
+#define __ASM_AVR32_USART3_H__
+
+/* USART3 register offsets */
+#define USART3_CR				0x0000
+#define USART3_MR				0x0004
+#define USART3_IER				0x0008
+#define USART3_IDR				0x000c
+#define USART3_IMR				0x0010
+#define USART3_CSR				0x0014
+#define USART3_RHR				0x0018
+#define USART3_THR				0x001c
+#define USART3_BRGR				0x0020
+#define USART3_RTOR				0x0024
+#define USART3_TTGR				0x0028
+#define USART3_FIDI				0x0040
+#define USART3_NER				0x0044
+#define USART3_XXR				0x0048
+#define USART3_IFR				0x004c
+
+/* PDC register offsets */
+#define USART3_RPR				0x100
+#define USART3_RCR				0x104
+#define USART3_TPR				0x108
+#define USART3_TCR				0x10c
+#define USART3_RNPR				0x110
+#define USART3_RNCR				0x114
+#define USART3_TNPR				0x118
+#define USART3_TNCR				0x11c
+#define USART3_PTCR				0x120
+#define USART3_PTSR				0x124
+
+/* Bitfields in CR */
+#define USART3_RSTRX_OFFSET			2
+#define USART3_RSTRX_SIZE			1
+#define USART3_RSTTX_OFFSET			3
+#define USART3_RSTTX_SIZE			1
+#define USART3_RXEN_OFFSET			4
+#define USART3_RXEN_SIZE			1
+#define USART3_RXDIS_OFFSET			5
+#define USART3_RXDIS_SIZE			1
+#define USART3_TXEN_OFFSET			6
+#define USART3_TXEN_SIZE			1
+#define USART3_TXDIS_OFFSET			7
+#define USART3_TXDIS_SIZE			1
+#define USART3_RSTSTA_OFFSET			8
+#define USART3_RSTSTA_SIZE			1
+#define USART3_STTBRK_OFFSET			9
+#define USART3_STTBRK_SIZE			1
+#define USART3_STPBRK_OFFSET			10
+#define USART3_STPBRK_SIZE			1
+#define USART3_STTTO_OFFSET			11
+#define USART3_STTTO_SIZE			1
+#define USART3_SENDA_OFFSET			12
+#define USART3_SENDA_SIZE			1
+#define USART3_RSTIT_OFFSET			13
+#define USART3_RSTIT_SIZE			1
+#define USART3_RSTNACK_OFFSET			14
+#define USART3_RSTNACK_SIZE			1
+#define USART3_RETTO_OFFSET			15
+#define USART3_RETTO_SIZE			1
+#define USART3_DTREN_OFFSET			16
+#define USART3_DTREN_SIZE			1
+#define USART3_DTRDIS_OFFSET			17
+#define USART3_DTRDIS_SIZE			1
+#define USART3_RTSEN_OFFSET			18
+#define USART3_RTSEN_SIZE			1
+#define USART3_RTSDIS_OFFSET			19
+#define USART3_RTSDIS_SIZE			1
+#define USART3_COMM_TX_OFFSET			30
+#define USART3_COMM_TX_SIZE			1
+#define USART3_COMM_RX_OFFSET			31
+#define USART3_COMM_RX_SIZE			1
+
+/* Bitfields in MR */
+#define USART3_USART_MODE_OFFSET		0
+#define USART3_USART_MODE_SIZE			4
+#define USART3_USCLKS_OFFSET			4
+#define USART3_USCLKS_SIZE			2
+#define USART3_CHRL_OFFSET			6
+#define USART3_CHRL_SIZE			2
+#define USART3_SYNC_OFFSET			8
+#define USART3_SYNC_SIZE			1
+#define USART3_PAR_OFFSET			9
+#define USART3_PAR_SIZE				3
+#define USART3_NBSTOP_OFFSET			12
+#define USART3_NBSTOP_SIZE			2
+#define USART3_CHMODE_OFFSET			14
+#define USART3_CHMODE_SIZE			2
+#define USART3_MSBF_OFFSET			16
+#define USART3_MSBF_SIZE			1
+#define USART3_MODE9_OFFSET			17
+#define USART3_MODE9_SIZE			1
+#define USART3_CLKO_OFFSET			18
+#define USART3_CLKO_SIZE			1
+#define USART3_OVER_OFFSET			19
+#define USART3_OVER_SIZE			1
+#define USART3_INACK_OFFSET			20
+#define USART3_INACK_SIZE			1
+#define USART3_DSNACK_OFFSET			21
+#define USART3_DSNACK_SIZE			1
+#define USART3_MAX_ITERATION_OFFSET		24
+#define USART3_MAX_ITERATION_SIZE		3
+#define USART3_FILTER_OFFSET			28
+#define USART3_FILTER_SIZE			1
+
+/* Bitfields in CSR */
+#define USART3_RXRDY_OFFSET			0
+#define USART3_RXRDY_SIZE			1
+#define USART3_TXRDY_OFFSET			1
+#define USART3_TXRDY_SIZE			1
+#define USART3_RXBRK_OFFSET			2
+#define USART3_RXBRK_SIZE			1
+#define USART3_ENDRX_OFFSET			3
+#define USART3_ENDRX_SIZE			1
+#define USART3_ENDTX_OFFSET			4
+#define USART3_ENDTX_SIZE			1
+#define USART3_OVRE_OFFSET			5
+#define USART3_OVRE_SIZE			1
+#define USART3_FRAME_OFFSET			6
+#define USART3_FRAME_SIZE			1
+#define USART3_PARE_OFFSET			7
+#define USART3_PARE_SIZE			1
+#define USART3_TIMEOUT_OFFSET			8
+#define USART3_TIMEOUT_SIZE			1
+#define USART3_TXEMPTY_OFFSET			9
+#define USART3_TXEMPTY_SIZE			1
+#define USART3_ITERATION_OFFSET			10
+#define USART3_ITERATION_SIZE			1
+#define USART3_TXBUFE_OFFSET			11
+#define USART3_TXBUFE_SIZE			1
+#define USART3_RXBUFF_OFFSET			12
+#define USART3_RXBUFF_SIZE			1
+#define USART3_NACK_OFFSET			13
+#define USART3_NACK_SIZE			1
+#define USART3_RIIC_OFFSET			16
+#define USART3_RIIC_SIZE			1
+#define USART3_DSRIC_OFFSET			17
+#define USART3_DSRIC_SIZE			1
+#define USART3_DCDIC_OFFSET			18
+#define USART3_DCDIC_SIZE			1
+#define USART3_CTSIC_OFFSET			19
+#define USART3_CTSIC_SIZE			1
+#define USART3_RI_OFFSET			20
+#define USART3_RI_SIZE				1
+#define USART3_DSR_OFFSET			21
+#define USART3_DSR_SIZE				1
+#define USART3_DCD_OFFSET			22
+#define USART3_DCD_SIZE				1
+#define USART3_CTS_OFFSET			23
+#define USART3_CTS_SIZE				1
+
+/* Bitfields in RHR */
+#define USART3_RXCHR_OFFSET			0
+#define USART3_RXCHR_SIZE			9
+
+/* Bitfields in THR */
+#define USART3_TXCHR_OFFSET			0
+#define USART3_TXCHR_SIZE			9
+
+/* Bitfields in BRGR */
+#define USART3_CD_OFFSET			0
+#define USART3_CD_SIZE				16
+
+/* Bitfields in RTOR */
+#define USART3_TO_OFFSET			0
+#define USART3_TO_SIZE				16
+
+/* Bitfields in TTGR */
+#define USART3_TG_OFFSET			0
+#define USART3_TG_SIZE				8
+
+/* Bitfields in FIDI */
+#define USART3_FI_DI_RATIO_OFFSET		0
+#define USART3_FI_DI_RATIO_SIZE			11
+
+/* Bitfields in NER */
+#define USART3_NB_ERRORS_OFFSET			0
+#define USART3_NB_ERRORS_SIZE			8
+
+/* Bitfields in XXR */
+#define USART3_XOFF_OFFSET			0
+#define USART3_XOFF_SIZE			8
+#define USART3_XON_OFFSET			8
+#define USART3_XON_SIZE				8
+
+/* Bitfields in IFR */
+#define USART3_IRDA_FILTER_OFFSET		0
+#define USART3_IRDA_FILTER_SIZE			8
+
+/* Bitfields in PTCR/PTSR (PDC) */
+#define USART3_RXTEN_OFFSET			0
+#define USART3_RXTEN_SIZE			1
+#define USART3_RXTDIS_OFFSET			1
+#define USART3_RXTDIS_SIZE			1
+#define USART3_TXTEN_OFFSET			8
+#define USART3_TXTEN_SIZE			1
+#define USART3_TXTDIS_OFFSET			9
+#define USART3_TXTDIS_SIZE			1
+
+/* Constants for USART_MODE */
+#define USART3_USART_MODE_NORMAL		0
+#define USART3_USART_MODE_RS485			1
+#define USART3_USART_MODE_HARDWARE		2
+#define USART3_USART_MODE_MODEM			3
+#define USART3_USART_MODE_ISO7816_T0		4
+#define USART3_USART_MODE_ISO7816_T1		6
+#define USART3_USART_MODE_IRDA			8
+
+/* Constants for USCLKS */
+#define USART3_USCLKS_MCK			0
+#define USART3_USCLKS_MCK_DIV			1
+#define USART3_USCLKS_SCK			3
+
+/* Constants for CHRL */
+#define USART3_CHRL_5				0
+#define USART3_CHRL_6				1
+#define USART3_CHRL_7				2
+#define USART3_CHRL_8				3
+
+/* Constants for PAR */
+#define USART3_PAR_EVEN				0
+#define USART3_PAR_ODD				1
+#define USART3_PAR_SPACE			2
+#define USART3_PAR_MARK				3
+#define USART3_PAR_NONE				4
+#define USART3_PAR_MULTI			6
+
+/* Constants for NBSTOP */
+#define USART3_NBSTOP_1				0
+#define USART3_NBSTOP_1_5			1
+#define USART3_NBSTOP_2				2
+
+/* Constants for CHMODE */
+#define USART3_CHMODE_NORMAL			0
+#define USART3_CHMODE_ECHO			1
+#define USART3_CHMODE_LOCAL_LOOP		2
+#define USART3_CHMODE_REMOTE_LOOP		3
+
+/* Constants for MSBF */
+#define USART3_MSBF_LSBF			0
+#define USART3_MSBF_MSBF			1
+
+/* Constants for OVER */
+#define USART3_OVER_X16				0
+#define USART3_OVER_X8				1
+
+/* Constants for CD */
+#define USART3_CD_DISABLE			0
+#define USART3_CD_BYPASS			1
+
+/* Constants for TO */
+#define USART3_TO_DISABLE			0
+
+/* Constants for TG */
+#define USART3_TG_DISABLE			0
+
+/* Constants for FI_DI_RATIO */
+#define USART3_FI_DI_RATIO_DISABLE		0
+
+/* Bit manipulation macros */
+#define USART3_BIT(name)				\
+	(1 << USART3_##name##_OFFSET)
+#define USART3_BF(name,value)				\
+	(((value) & ((1 << USART3_##name##_SIZE) - 1))	\
+	 << USART3_##name##_OFFSET)
+#define USART3_BFEXT(name,value)			\
+	(((value) >> USART3_##name##_OFFSET)		\
+	 & ((1 << USART3_##name##_SIZE) - 1))
+#define USART3_BFINS(name,value,old)			\
+	(((old) & ~(((1 << USART3_##name##_SIZE) - 1)	\
+		    << USART3_##name##_OFFSET))		\
+	 | USART3_BF(name,value))
+
+/* Register access macros */
+#define usart3_readl(port,reg)				\
+	__raw_readl((port)->regs + USART3_##reg)
+#define usart3_writel(port,reg,value)			\
+	__raw_writel((value), (port)->regs + USART3_##reg)
+
+#endif /* __ASM_AVR32_USART3_H__ */