diff options
Diffstat (limited to 'libloragw/library.cfg')
| -rw-r--r-- | libloragw/library.cfg | 71 |
1 files changed, 49 insertions, 22 deletions
diff --git a/libloragw/library.cfg b/libloragw/library.cfg index 0e8c742..5751cb5 100644 --- a/libloragw/library.cfg +++ b/libloragw/library.cfg @@ -1,27 +1,54 @@ -# / _____) _ | | -# ( (____ _____ ____ _| |_ _____ ____| |__ -# \____ \| ___ | (_ _) ___ |/ ___) _ \ -# _____) ) ____| | | || |_| ____( (___| | | | -# (______/|_____)_|_|_| \__)_____)\____)_| |_| -# ©2013 Semtech-Cycleo -# -# Description: -# Lora gateway Hardware Abstraction Layer library configuration +# That file will be included in the Makefile files that have hardware dependencies +### SPI interface to the concentrator ### +# Accepted values: +# native Linux native SPI driver (/dev/spidev0.0) +# ftdi FTDI SPI-over-USB bridge using libmpsse/libftdi/libusb -# Set the DEBUG_* to 1 to activate debug mode in individual modules. -# Warning: that makes the module *very verbose*, do not use for production -FLAG_AUX= -D DEBUG_AUX=0 -FLAG_SPI= -D DEBUG_SPI=0 -FLAG_REG= -D DEBUG_REG=0 -FLAG_HAL= -D DEBUG_HAL=0 -FLAG_GPS= -D DEBUG_GPS=0 +CFG_SPI= ftdi + +### Concentrator chip ### +# Accepted values: +# sx1301 Semtech SX1301 production chip +# fpga1301 FPGA containing the SX1301 IP + +CFG_CHIP= sx1301 + +### Radio chip(s) ### +# Accepted values: +# sx1257 Dual SX1257 transceivers, covering 860-1000 MHz +# sx1255 Dual SX1255 transceivers, covering 400-510 MHz + +CFG_RADIO= sx1257 -# The flags bellow define which physical link to the nano board will be used -# Pick one and comment the other(s) +### RF band configuration ### +# Used to configured frequency restrictions (eg. if a SAW filter is installed) +# Accepted values: +# full Full range supported by the radio(s) +# eu868 ETSI 868 (866) MHz band +# us915 FCC 915 MHz band +# cn470 China 470 MHz band +# eu433 ETSI 433 MHz band -# FTDI SPI-over-USB bridge -LGW_PHY= ftdi +CFG_BAND= eu868 + +### Board misc parameters & calibration ### +# Used to configure misc board options. +# RX RSSI indication and TX power are highly dependant on radio, band, filter +# and RF front-ends, and must be calibrated for each new board design. +# Available calibration parameters: +# dev_nano_868 FPGA-based nano-concentrator, with 868 MHz SAW filter +# ref_1301_57nf SX1301 reference board with SX1257 radios, no filters +# Keep empty for no calibration parameters (neutral values will be used). + +CFG_BRD= ref_1301_57nf + +### Debug options ### +# Set the DEBUG_* to 1 to activate debug mode in individual modules. +# Warning: that makes the module *very verbose*, do not use for production -# Pcduino native SPI (Linux device in /dev) -#LGW_PHY= native +DEBUG_AUX= 0 +DEBUG_SPI= 0 +DEBUG_REG= 0 +DEBUG_HAL= 0 +DEBUG_GPS= 0 |