1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
|
Index: u-boot-1.3.2/board/freescale/mpc8313erdb/mpc8313erdb.c
===================================================================
--- u-boot-1.3.2.orig/board/freescale/mpc8313erdb/mpc8313erdb.c 2009-01-15 10:51:45.000000000 +0100
+++ u-boot-1.3.2/board/freescale/mpc8313erdb/mpc8313erdb.c 2009-01-15 12:18:31.000000000 +0100
@@ -28,6 +28,7 @@
#endif
#include <pci.h>
#include <mpc83xx.h>
+#include <spi.h>
DECLARE_GLOBAL_DATA_PTR;
@@ -107,3 +108,29 @@
#endif
}
#endif
+
+
+/*
+ * The following are used to control the SPI chip selects for the SPI command.
+ */
+#ifdef CONFIG_HARD_SPI
+
+void spi_rfid_chipsel(int cs)
+{
+ if(cs)
+ gpio_clear(14);
+ else
+ gpio_set(14);
+}
+
+/*
+ * The SPI command uses this table of functions for controlling the SPI
+ * chip selects.
+ */
+spi_chipsel_type spi_chipsel[] = {
+ spi_rfid_chipsel,
+};
+int spi_chipsel_cnt = sizeof(spi_chipsel) / sizeof(spi_chipsel[0]);
+
+#endif /* CONFIG_HARD_SPI */
+
Index: u-boot-1.3.2/include/configs/MPC8313ERDB.h
===================================================================
--- u-boot-1.3.2.orig/include/configs/MPC8313ERDB.h 2009-01-15 10:51:51.000000000 +0100
+++ u-boot-1.3.2/include/configs/MPC8313ERDB.h 2009-01-15 12:16:57.000000000 +0100
@@ -369,6 +369,7 @@
#define CONFIG_CMD_PCI
#define CONFIG_CMD_NAND
#define CONFIG_CMD_JFFS2
+#define CONFIG_CMD_SPI
#if defined(CFG_RAMBOOT)
#undef CONFIG_CMD_ENV
@@ -386,6 +387,11 @@
#define MTDPARTS_DEFAULT "mtdparts=physmap-flash.0:384k(uboot),64k(env)"
+/* SPI */
+#define CONFIG_MPC8XXX_SPI
+#define CONFIG_HARD_SPI /* SPI with hardware support */
+#undef CONFIG_SOFT_SPI /* SPI bit-banged */
+
/*
* Miscellaneous configurable options
*/
Index: u-boot-1.3.2/drivers/spi/mpc8xxx_spi.c
===================================================================
--- u-boot-1.3.2.orig/drivers/spi/mpc8xxx_spi.c 2009-01-15 10:52:30.000000000 +0100
+++ u-boot-1.3.2/drivers/spi/mpc8xxx_spi.c 2009-01-15 10:53:23.000000000 +0100
@@ -34,6 +34,8 @@
#define SPI_MODE_REV (0x80000000 >> 5) /* Reverse mode - MSB first */
#define SPI_MODE_MS (0x80000000 >> 6) /* Always master */
#define SPI_MODE_EN (0x80000000 >> 7) /* Enable interface */
+#define SPI_MODE_DIV16 (0x80000000 >> 4) /*Divide by 16. */
+#define SPI_MODE_LEN_8 (0x00700000) /*0111 8-bit characters*/
#define SPI_TIMEOUT 1000
@@ -45,9 +47,7 @@
* SPI pins on the MPC83xx are not muxed, so all we do is initialize
* some registers
*/
- spi->mode = SPI_MODE_REV | SPI_MODE_MS | SPI_MODE_EN;
- spi->mode = (spi->mode & 0xfff0ffff) | (1 << 16); /* Use SYSCLK / 8
- (16.67MHz typ.) */
+ spi->mode = SPI_MODE_DIV16 |SPI_MODE_LEN_8| SPI_MODE_REV | SPI_MODE_MS | SPI_MODE_EN;
spi->event = 0xffffffff; /* Clear all SPI events */
spi->mask = 0x00000000; /* Mask all SPI interrupts */
spi->com = 0; /* LST bit doesn't do anything, so disregard */
|
