blob: ecb3189741e142012d405ec197d4c62b76288cbf (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
|
# This describes a generic SlugOS image, even though the bb file is
# called 'slugos-image.bb' the distro specific configuration is
# done in conf/distro/${DISTRO}.conf (which should always include
# conf/distro/slugos.conf to get the standard settings).
#
DESCRIPTION = "Task packages for the SlugOS distribution"
HOMEPAGE = "http://www.nslu2-linux.org"
LICENSE = "MIT"
PR = "r15"
PACKAGE_ARCH = "${MACHINE_ARCH}"
ALLOW_EMPTY = "1"
#----------------------------------------------------------------------------------
# FIRMWARE CONFIGURATION
#----------------------------------------------------------------------------------
# EXTRA PACKAGES
# --------------
# The standard firmware contents and additional packages built as requirements
# of the firmware are defined here in SLUGOS_STANDARD_RDEPENDS.
SLUGOS_STANDARD_RDEPENDS = ""
SLUGOS_STANDARD_RRECOMMENDS = ""
# diff, cpio and find are required for reflash and turnup ram.
# Removing these probably leaves the system bootable, but standard
# openslug and ucslugc stuff won't work, so only take these out in
# very non-standard turnkey slugos builds.
#
# udev is the default way of handling devices, there is no guarantee
# that the static device table is completely correct (it is just
# known to be sufficient for boot.)
SLUGOS_STANDARD_RRECOMMENDS += "diffutils cpio findutils"
# These lines add support for formatting ext2 and ext3 file systems
# on a hard disk attached to the NSLU2. ext3 is the standard Linux
# file system.
SLUGOS_STANDARD_RRECOMMENDS += "e2fsprogs-mke2fs e2fsprogs-fsck e2fsprogs-e2fsck e2fsprogs-badblocks"
# These lines add support for an X/Y/ZModem package called lrzsz
# (this is of use for people with modified NSLU2 hardware which
# supports a serial port.)
SLUGOS_STANDARD_RRECOMMENDS += "lrzsz"
# Filesystem selection. Adding entries here adds the module to the
# image. The module must be built as part of nslu2-kernel (i.e. it
# must be specified as a module in the defconfig file). The NLS
# support charset modules must be given explicitly and must match
# the codepage/iocharset and NLS handling for the file systems which
# require them. The installed lanugage set is minimal but sufficient
# for any file system (since it uses utf8). See
# http://www.nslu2-linux.orgwiki/HowTo/MountFATFileSystems
# for more information on the language behaviour of the DOS file
# systems.
#
# KERNEL LEVEL FILE SYSTEM SUPPORT
# --------------------------------
# NOTE: removing kernel-module-nfs from this list will prevent NFS
# boot (however you can do a simple flash file system boot - no
# attached disk - and install the nfs modules from ssh.)
# The altboot mechanism requires kernel-module-loop.
SLUGOS_STANDARD_RRECOMMENDS += "\
kernel-module-ext2 \
kernel-module-jbd \
kernel-module-ext3 \
kernel-module-vfat \
kernel-module-nls-cp437 \
kernel-module-nls-utf8 \
"
# Add daemon required for HW RNG support
SLUGOS_RNG_TOOLS_PACKAGE = "rng-tools"
SLUGOS_RNG_TOOLS_PACKAGE_linux-uclibc = ""
SLUGOS_STANDARD_RRECOMMENDS += "\
${SLUGOS_RNG_TOOLS_PACKAGE} \
"
# Add modules required for usb support
SLUGOS_STANDARD_RRECOMMENDS += "\
kernel-module-ehci-hcd \
kernel-module-ohci-hcd \
kernel-module-uhci-hcd \
"
# Add modules required for IDE support
# SLUGOS_STANDARD_RRECOMMENDS += "\
# "
# Add modules required for Network support
SLUGOS_STANDARD_RRECOMMENDS += "\
kernel-module-mii \
kernel-module-ixp4xx-mac \
kernel-module-ixp4xx-qmgr \
kernel-module-via-velocity \
"
# portmap \
# kexec-tools \
# kernel-module-nfs \
# kernel-module-isofs \
# kernel-module-udf \
# kernel-module-loop \
# kernel-module-libata \
# kernel-module-pata-artop \
# kernel-module-netconsole \
# wpa-supplicant \
# zd1211-firmware kernel-module-zd1211rw \
# madwifi-ng-modules madwifi-ng-tools wireless-tools \
DISTRO_EXTRA_DEPENDS ?= ""
DEPENDS += "${DISTRO_EXTRA_DEPENDS}"
DISTRO_EXTRA_RDEPENDS ?= ""
RDEPENDS += "\
kernel ixp4xx-npe \
base-files base-passwd netbase \
busybox initscripts-slugos slugos-init \
update-modules sysvinit tinylogin udev \
module-init-tools modutils-initscripts \
ipkg-collateral ipkg ipkg-link \
beep \
e2fsprogs-blkid \
util-linux-mount \
util-linux-umount \
util-linux-swaponoff \
util-linux-losetup \
${SLUGOS_STANDARD_RDEPENDS} \
${DISTRO_EXTRA_RDEPENDS}"
RRECOMMENDS += "\
openssh \
${SLUGOS_STANDARD_RRECOMMENDS} \
${DISTRO_EXTRA_RRECOMMENDS}"
|
