blob: 3707316c1ed9b69a3956d0328f21e9827ebedac7 (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
|
# This describes a generic SlugOS image, even though the bb file is
# called 'slugos-image.bb' the distro specific configuration is
# done in conf/distro/${DISTRO}.conf (which should always include
# conf/distro/slugos.conf to get the standard settings).
#
DESCRIPTION = "Task packages for the SlugOS distribution"
HOMEPAGE = "http://www.nslu2-linux.org"
LICENSE = "MIT"
PR = "r3"
PACKAGE_ARCH = "${MACHINE_ARCH}"
ALLOW_EMPTY = "1"
#----------------------------------------------------------------------------------
# FIRMWARE CONFIGURATION
#----------------------------------------------------------------------------------
# EXTRA PACKAGES
# --------------
# The standard firmware contents and additional packages built as requirements
# of the firmware are defined here in SLUGOS_STANDARD_RDEPENDS.
SLUGOS_STANDARD_RDEPENDS = ""
# diff, cpio and find are required for reflash and turnup ram.
# Removing these probably leaves the system bootable, but standard
# openslug and ucslugc stuff won't work, so only take these out in
# very non-standard turnkey slugos builds.
#
# udev is the default way of handling devices, there is no guarantee
# that the static device table is completely correct (it is just
# known to be sufficient for boot.)
SLUGOS_STANDARD_RDEPENDS += "diffutils cpio findutils udev"
# These lines add support for formatting ext2 and ext3 file systems
# on a hard disk attached to the NSLU2. ext3 is the standard Linux
# file system.
SLUGOS_STANDARD_RDEPENDS += "e2fsprogs-mke2fs e2fsprogs-fsck e2fsprogs-e2fsck e2fsprogs-badblocks"
# These lines add support for an X/Y/ZModem package called lrzsz
# (this is of use for people with modified NSLU2 hardware which
# supports a serial port.)
SLUGOS_STANDARD_RDEPENDS += "lrzsz"
# Filesystem selection. Adding entries here adds the module to the
# image. The module must be built as part of nslu2-kernel (i.e. it
# must be specified as a module in the defconfig file). The NLS
# support charset modules must be given explicitly and must match
# the codepage/iocharset and NLS handling for the file systems which
# require them. The installed lanugage set is minimal but sufficient
# for any file system (since it uses utf8). See
# http://www.nslu2-linux.orgwiki/HowTo/MountFATFileSystems
# for more information on the language behaviour of the DOS file
# systems.
#
# KERNEL LEVEL FILE SYSTEM SUPPORT
# --------------------------------
# NOTE: removing kernel-module-nfs from this list will prevent NFS
# boot (however you can do a simple flash file system boot - no
# attached disk - and install the nfs modules from ssh.)
SLUGOS_STANDARD_RDEPENDS += "\
kernel-module-ext2 \
kernel-module-jbd \
kernel-module-ext3 \
kernel-module-vfat \
kernel-module-ntfs \
kernel-module-isofs \
kernel-module-udf \
kernel-module-nls-cp437 \
kernel-module-nls-utf8 \
"
# Add daemon required for HW RNG support
SLUGOS_STANDARD_RDEPENDS += "\
rng-tools \
"
# Add modules required for usb support
SLUGOS_STANDARD_RDEPENDS += "\
kernel-module-ohci-hcd \
kernel-module-uhci-hcd \
"
# Add modules required for IDE support
SLUGOS_STANDARD_RDEPENDS += "\
kernel-module-libata \
kernel-module-pata-artop \
"
# Add modules required for Network support
SLUGOS_STANDARD_RDEPENDS += "\
kernel-module-via-velocity \
"
# Add modules required for Network Console support
# NOTE: This module is desirable for systems lacking a physical
# console, but is usually only enabled if specific needs or issues
# arise. If space in the flash is at a premium, it can be omitted.
SLUGOS_STANDARD_RDEPENDS += "\
kernel-module-netconsole \
"
DEPENDS += "${DISTRO_EXTRA_DEPENDS}"
RDEPENDS += "kernel ixp4xx-npe \
base-files base-passwd netbase \
busybox initscripts-slugos slugos-init \
update-modules sysvinit tinylogin \
module-init-tools modutils-initscripts \
ipkg-collateral ipkg ipkg-link \
portmap \
dropbear \
beep \
e2fsprogs-blkid \
util-linux-mount \
util-linux-umount \
util-linux-swaponoff \
util-linux-losetup \
${SLUGOS_STANDARD_RDEPENDS} \
${DISTRO_EXTRA_RDEPENDS}"
RRECOMMENDS = "${DISTRO_EXTRA_RRECOMMENDS}"
|
