1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
|
TWL4030: clear TWL GPIO interrupt status registers
From: Paul Walmsley <paul@pwsan.com>
twl_init_irq() does not clear the TWL GPIO ISR registers, but the PIH
ISR thinks that it has. This causes any previously-latched GPIO interrupts
to be stuck on until twl4030-gpio.c initializes, often drowning the console in
TWL4030 module irq 368 is disabled but can't be masked!
messages. This seems to be a particular problem when booting on Beagle.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
---
drivers/i2c/chips/twl4030-core.c | 42 ++++++++++++++++++++++++++++++++++++++
1 files changed, 42 insertions(+), 0 deletions(-)
diff --git a/drivers/i2c/chips/twl4030-core.c b/drivers/i2c/chips/twl4030-core.c
index ff662bc..dfc3805 100644
--- a/drivers/i2c/chips/twl4030-core.c
+++ b/drivers/i2c/chips/twl4030-core.c
@@ -857,6 +857,48 @@ static void twl_init_irq(void)
return;
}
+ /* GPIO_ISR1A */
+ res = twl4030_i2c_write_u8(TWL4030_MODULE_GPIO, 0xff, 0x19);
+ if (res < 0) {
+ pr_err("%s[%d][%d]\n", msg, res, __LINE__);
+ return;
+ }
+
+ /* GPIO_ISR2A */
+ res = twl4030_i2c_write_u8(TWL4030_MODULE_GPIO, 0xff, 0x1a);
+ if (res < 0) {
+ pr_err("%s[%d][%d]\n", msg, res, __LINE__);
+ return;
+ }
+
+ /* GPIO_ISR3A */
+ res = twl4030_i2c_write_u8(TWL4030_MODULE_GPIO, 0xff, 0x1b);
+ if (res < 0) {
+ pr_err("%s[%d][%d]\n", msg, res, __LINE__);
+ return;
+ }
+
+ /* GPIO_ISR1B */
+ res = twl4030_i2c_write_u8(TWL4030_MODULE_GPIO, 0xff, 0x1f);
+ if (res < 0) {
+ pr_err("%s[%d][%d]\n", msg, res, __LINE__);
+ return;
+ }
+
+ /* GPIO_ISR2B */
+ res = twl4030_i2c_write_u8(TWL4030_MODULE_GPIO, 0xff, 0x20);
+ if (res < 0) {
+ pr_err("%s[%d][%d]\n", msg, res, __LINE__);
+ return;
+ }
+
+ /* GPIO_ISR3B */
+ res = twl4030_i2c_write_u8(TWL4030_MODULE_GPIO, 0xff, 0x21);
+ if (res < 0) {
+ pr_err("%s[%d][%d]\n", msg, res, __LINE__);
+ return;
+ }
+
/* install an irq handler for each of the PIH modules */
for (i = TWL4030_IRQ_BASE; i < TWL4030_IRQ_END; i++) {
set_irq_chip(i, &twl4030_irq_chip);
|
