diff options
Diffstat (limited to 'recipes/linux/linux-omap2-git/beagleboard/omap23-pm-noop.eml')
| -rw-r--r-- | recipes/linux/linux-omap2-git/beagleboard/omap23-pm-noop.eml | 894 |
1 files changed, 894 insertions, 0 deletions
diff --git a/recipes/linux/linux-omap2-git/beagleboard/omap23-pm-noop.eml b/recipes/linux/linux-omap2-git/beagleboard/omap23-pm-noop.eml new file mode 100644 index 0000000000..48ff5da822 --- /dev/null +++ b/recipes/linux/linux-omap2-git/beagleboard/omap23-pm-noop.eml @@ -0,0 +1,894 @@ +The interface provides device drivers, CPUFreq, and DSP Bridge with a +means of controlling OMAP power management parameters that are not yet +supported by the Linux PM PMQOS interface. Copious documentation and +rationale is in the patch in Documentation/arm/OMAP/omap_pm and the +interface header file, include/asm-arm/arch-omap/omap-pm.h. + +Signed-off-by: Paul Walmsley <paul@pwsan.com> +--- + + Documentation/arm/OMAP/omap_pm | 185 +++++++++++++++++++++ + arch/arm/mach-omap2/io.c | 4 + arch/arm/plat-omap/Kconfig | 13 + + arch/arm/plat-omap/Makefile | 1 + arch/arm/plat-omap/omap-pm-noop.c | 309 +++++++++++++++++++++++++++++++++++ + include/asm-arm/arch-omap/omap-pm.h | 300 ++++++++++++++++++++++++++++++++++ + 6 files changed, 812 insertions(+), 0 deletions(-) + create mode 100644 Documentation/arm/OMAP/omap_pm + create mode 100644 arch/arm/plat-omap/omap-pm-noop.c + create mode 100644 include/asm-arm/arch-omap/omap-pm.h + +diff --git a/Documentation/arm/OMAP/omap_pm b/Documentation/arm/OMAP/omap_pm +new file mode 100644 +index 0000000..2ec2034 +--- /dev/null ++++ b/Documentation/arm/OMAP/omap_pm +@@ -0,0 +1,185 @@ ++ ++Rationale: the OMAP PM interface ++================================ ++ ++ ++Existing PM interfaces are currently not ideal for OMAP ++------------------------------------------------------- ++ ++There are two PM interfaces in use with publicly-distributed OMAP ++Linux code: the TI Shared Resource Framework (SRF) and the Linux PM ++QoS parameters code. Neither interface is ideal for Linux OMAP code. ++ ++TI Shared Resource Framework: ++ ++The TI CDP 12.14 tree drivers currently use the TI Shared Resource ++Framework (SRF) to control chip power management. Use of the SRF ++allowed TI to get the drivers up and running quickly with considerable ++power savings; and the SRF provided debugging support. However, many ++of the SRF parameters are specified in OMAP-specific terms, such as ++target OPPs, rather than in terms of actual latency or throughput ++requirements. OPPs change depending on OMAP silicon revisions or OMAP ++types, and are meaningless for other architectures, so drivers shared ++between OMAP and other architectures would also have to #ifdef out the ++SRF constraints. ++ ++Linux PM QoS parameters: ++ ++In February 2008, the mainline Linux kernel added code that is ++somewhat similar to the SRF: the Linux PM QoS parameters code, located ++in kernel/pm_qos_params.c. (This code replaced the latency management ++code that was present in earlier kernels.) Ideally, OMAP drivers ++would be able to use this Linux PM QoS code directly, but the PM QoS ++code has some drawbacks: ++ ++- It combines some power management parameters that should be kept ++ separate for maximum power savings on OMAP3. For example, in the PM ++ QoS code, CPU and system DMA wakeup latency are combined into one ++ parameter; but on OMAP3, these are distinct parameters. The Linux ++ PM QoS code also combines all network power management knobs into ++ two non-device-specific parameters. OMAP2/3 systems can have ++ different network devices with different power management ++ requirements - for example, a wired Ethernet interface may have ++ different latency and throughput constraints than a WiFi interface. ++ ++- It does not yet cover all of the power management capabilities of ++ the OMAP3 architecture. It does not express latency constraints on ++ a per-device or per-powerdomain basis; it only covers ++ cpu_dma_latency and network throughput and latency, which would not ++ cover most of the OMAP3 devices. ++ ++The result is that drivers using the current Linux PM QoS layer ++directly are unlikely to reach the same level of power efficiency as ++driver code using the Shared Resource Framework. ++ ++To summarize, the SRF provides significant power savings, but ++expresses power constraints in an OMAP- and silicon-revision-specific ++way; and the PM QoS layer expresses PM constraints in a cross-platform ++manner (in terms of fundamental physical units), but does not support ++per-powerdomain constraints and does not cover many of the OMAP power ++management features. ++ ++ ++A medium-term alternative: the OMAP PM interface ++------------------------------------------------ ++ ++We need a way for driver code to express PM parameters which: ++ ++- supports the range of power management parameters present in the TI SRF; ++ ++- separates the drivers from the underlying PM parameter ++ implementation, whether it is the TI SRF or Linux PM QoS or Linux ++ latency framework or something else; ++ ++- specifies PM parameters in terms of fundamental units, such as ++ latency and throughput, rather than units which are specific to OMAP ++ or to particular OMAP variants; ++ ++- allows drivers which are shared with other architectures (e.g., ++ DaVinci) to add these constraints in a way which won't affect non-OMAP ++ systems, ++ ++- can be implemented immediately with minimal disruption of other ++ architectures. ++ ++ ++We therefore propose the OMAP PM interface, including the following ++four power management functions for driver code: ++ ++1. Set the maximum MPU wakeup latency: ++ (*pdata->set_max_mpu_wakeup_lat)(struct device *dev, unsigned long t) ++ ++2. Set the maximum device wakeup latency: ++ (*pdata->set_max_dev_wakeup_lat)(struct device *dev, unsigned long t) ++ ++3. Set the maximum system DMA transfer start latency (CORE pwrdm): ++ (*pdata->set_max_sdma_lat)(struct device *dev, long t) ++ ++4. Set the minimum bus throughput needed by a device: ++ (*pdata->set_min_bus_tput)(struct device *dev, u8 agent_id, unsigned long r) ++ ++ ++These functions are extensively documented in the OMAP PM interface header ++file, included in the patch. ++ ++ ++The OMAP PM layer is intended to be temporary ++--------------------------------------------- ++ ++The intention is that, in time, the Linux PM QoS layer should support ++the range of power management features present in OMAP3. As this ++happens, existing drivers using the OMAP PM interface can be modified ++to use the Linux PM QoS code; and the OMAP PM interface can disappear. ++ ++ ++Driver usage of the OMAP PM functions ++------------------------------------- ++ ++As the 'pdata' in the above examples indicates, these functions are ++exposed to drivers through function pointers in driver .platform_data ++structures. The function pointers are initialized by the board-*.c ++files to point to the corresponding OMAP PM functions: ++.set_max_dev_wakeup_lat will point to ++omap_pm_set_max_dev_wakeup_lat(), etc. Other architectures which do ++not support these functions should leave these function pointers set ++to NULL. Drivers should use the following idiom: ++ ++ if (pdata->set_max_dev_wakeup_lat) ++ (*pdata->set_max_dev_wakeup_lat)(dev, t); ++ ++The most common usage of these functions will probably be to specify ++the maximum time from when an interrupt occurs, to when the device ++becomes accessible. To accomplish this, driver writers should use the ++set_max_mpu_wakeup_lat() function to to constrain the MPU wakeup ++latency, and the set_max_dev_wakeup_lat() function to constrain the ++device wakeup latency (from clk_enable() to accessibility). For ++example, ++ ++ /* Limit MPU wakeup latency */ ++ if (pdata->set_max_mpu_wakeup_lat) ++ (*pdata->set_max_mpu_wakeup_lat)(dev, tc); ++ ++ /* Limit device powerdomain wakeup latency */ ++ if (pdata->set_max_dev_wakeup_lat) ++ (*pdata->set_max_dev_wakeup_lat)(dev, td); ++ ++ /* total wakeup latency in this example: (tc + td) */ ++ ++ ++The PM parameters can be overwritten by calling the function again ++with the new value. The settings can be removed by calling the ++function with a t argument of -1 (except in the case of ++set_max_bus_tput(), which should be called with an r argument of 0). ++ ++ ++Other specialized interface functions ++------------------------------------- ++ ++The four functions listed above are intended to be usable by any ++device driver. However, DSPBridge and CPUFreq have special ++requirements. DSPBridge expresses target DSP performance levels in ++terms of OPP IDs. CPUFreq expresses target MPU performance levels in ++terms of MPU frequency. The OMAP PM interface contains functions for ++these specialized cases to convert that input information (OPPs/MPU ++frequency) into the form that the underlying power management ++implementation needs: ++ ++5. (*pdata->omap_pm_dsp_get_opp_table)(void) ++ ++6. (*pdata->omap_pm_dsp_set_min_opp)(u8 opp_id) ++ ++7. (*pdata->omap_pm_dsp_get_opp)(void) ++ ++8. (*pdata->omap_pm_cpu_get_freq_table)(void) ++ ++9. (*pdata->omap_pm_cpu_set_freq)(unsigned long f) ++ ++10. (*pdata->omap_pm_cpu_get_freq)(void) ++ ++ ++There are also functions for use by the clockdomain layer to indicate ++that a powerdomain should wake up or be put to sleep: ++ ++11. (*pdata->omap_pm_pwrdm_active)(struct powerdomain *pwrdm) ++ ++12. (*pdata->omap_pm_pwrdm_inactive)(struct powerdomain *pwrdm) +diff --git a/arch/arm/plat-omap/Kconfig b/arch/arm/plat-omap/Kconfig +index 960c13f..ca790ac 100644 +--- a/arch/arm/plat-omap/Kconfig ++++ b/arch/arm/plat-omap/Kconfig +@@ -247,4 +247,17 @@ config OMAP_SERIAL_WAKE + + endmenu + ++choice ++ prompt "OMAP PM layer selection" ++ depends on ARCH_OMAP ++ default OMAP_PM_NOOP ++ ++config OMAP_PM_NONE ++ bool "No PM layer" ++ ++config OMAP_PM_NOOP ++ bool "No-op/debug PM layer" ++ ++endchoice ++ + endif +diff --git a/arch/arm/plat-omap/Makefile b/arch/arm/plat-omap/Makefile +index 93bbb64..d5453d5 100644 +--- a/arch/arm/plat-omap/Makefile ++++ b/arch/arm/plat-omap/Makefile +@@ -29,3 +29,4 @@ obj-$(CONFIG_OMAP_MMU_FWK) += mmu.o + # OMAP mailbox framework + obj-$(CONFIG_OMAP_MBOX_FWK) += mailbox.o + ++obj-$(CONFIG_OMAP_PM_NOOP) += omap-pm-noop.o +\ No newline at end of file +diff --git a/arch/arm/plat-omap/omap-pm-noop.c b/arch/arm/plat-omap/omap-pm-noop.c +new file mode 100644 +index 0000000..5ff7962 +--- /dev/null ++++ b/arch/arm/plat-omap/omap-pm-noop.c +@@ -0,0 +1,309 @@ ++/* ++ * omap-pm-noop.c - OMAP power management interface - dummy version ++ * ++ * This code implements the OMAP power management interface to ++ * drivers, CPUIdle, CPUFreq, and DSP Bridge. It is strictly for ++ * debug/demonstration use, as it does nothing but printk() whenever a ++ * function is called (when DEBUG is defined, below) ++ * ++ * Copyright (C) 2008 Texas Instruments, Inc. ++ * Copyright (C) 2008 Nokia Corporation ++ * Paul Walmsley ++ * ++ * Interface developed by (in alphabetical order): ++ * Karthik Dasu, Amish Lakhani, Tony Lindgren, Rajendra Nayak, Sakari ++ * Poussa, Veeramanikandan Raju, Igor Stoppa, Paul Walmsley, Richard ++ * Woodruff ++ */ ++ ++#undef DEBUG ++ ++#include <linux/init.h> ++#include <linux/cpufreq.h> ++#include <linux/device.h> ++ ++/* Interface documentation is in asm/arch/omap-pm.h */ ++#include <asm/arch/omap-pm.h> ++ ++#include <asm/arch/powerdomain.h> ++ ++static struct omap_opp *dsp_opps; ++static struct omap_opp *mpu_opps; ++ ++/* ++ * Device-driver-originated constraints (via board-*.c files) ++ */ ++ ++void omap_pm_set_max_mpu_wakeup_lat(struct device *dev, long t) ++{ ++ if (!dev || t < -1) { ++ WARN_ON(1); ++ return; ++ }; ++ ++ if (t == -1) ++ pr_debug("OMAP PM: remove max MPU wakeup latency constraint: " ++ "dev %s\n", dev_name(dev)); ++ else ++ pr_debug("OMAP PM: add max MPU wakeup latency constraint: " ++ "dev %s, t = %ld usec\n", dev_name(dev), t); ++ ++ /* ++ * For current Linux, this needs to map the MPU to a ++ * powerdomain, then go through the list of current max lat ++ * constraints on the MPU and find the smallest. If ++ * the latency constraint has changed, the code should ++ * recompute the state to enter for the next powerdomain ++ * state. ++ * ++ * TI CDP code can call constraint_set here. ++ */ ++} ++ ++void omap_pm_set_min_bus_tput(struct device *dev, u8 agent_id, unsigned long r) ++{ ++ if (!dev || agent_id != OCP_INITIATOR_AGENT || ++ agent_id != OCP_TARGET_AGENT) { ++ WARN_ON(1); ++ return; ++ }; ++ ++ if (r == 0) ++ pr_debug("OMAP PM: remove min bus tput constraint: " ++ "dev %s for agent_id %d\n", dev_name(dev), agent_id); ++ else ++ pr_debug("OMAP PM: add min bus tput constraint: " ++ "dev %s for agent_id %d: rate %ld KiB\n", ++ dev_name(dev), agent_id, r); ++ ++ /* ++ * This code should model the interconnect and compute the ++ * required clock frequency, convert that to a VDD2 OPP ID, then ++ * set the VDD2 OPP appropriately. ++ * ++ * TI CDP code can call constraint_set here on the VDD2 OPP. ++ */ ++} ++ ++void omap_pm_set_max_dev_wakeup_lat(struct device *dev, long t) ++{ ++ if (!dev || t < -1) { ++ WARN_ON(1); ++ return; ++ }; ++ ++ if (t == -1) ++ pr_debug("OMAP PM: remove max device latency constraint: " ++ "dev %s\n", dev_name(dev)); ++ else ++ pr_debug("OMAP PM: add max device latency constraint: " ++ "dev %s, t = %ld usec\n", dev_name(dev), t); ++ ++ /* ++ * For current Linux, this needs to map the device to a ++ * powerdomain, then go through the list of current max lat ++ * constraints on that powerdomain and find the smallest. If ++ * the latency constraint has changed, the code should ++ * recompute the state to enter for the next powerdomain ++ * state. Conceivably, this code should also determine ++ * whether to actually disable the device clocks or not, ++ * depending on how long it takes to re-enable the clocks. ++ * ++ * TI CDP code can call constraint_set here. ++ */ ++} ++ ++void omap_pm_set_max_sdma_lat(struct device *dev, long t) ++{ ++ if (!dev || t < -1) { ++ WARN_ON(1); ++ return; ++ }; ++ ++ if (t == -1) ++ pr_debug("OMAP PM: remove max DMA latency constraint: " ++ "dev %s\n", dev_name(dev)); ++ else ++ pr_debug("OMAP PM: add max DMA latency constraint: " ++ "dev %s, t = %ld usec\n", dev_name(dev), t); ++ ++ /* ++ * For current Linux PM QOS params, this code should scan the ++ * list of maximum CPU and DMA latencies and select the ++ * smallest, then set cpu_dma_latency pm_qos_param ++ * accordingly. ++ * ++ * For future Linux PM QOS params, with separate CPU and DMA ++ * latency params, this code should just set the dma_latency param. ++ * ++ * TI CDP code can call constraint_set here. ++ */ ++ ++} ++ ++ ++/* ++ * DSP Bridge-specific constraints ++ */ ++ ++const struct omap_opp *omap_pm_dsp_get_opp_table(void) ++{ ++ pr_debug("OMAP PM: DSP request for OPP table\n"); ++ ++ /* ++ * Return DSP frequency table here: The final item in the ++ * array should have .rate = .opp_id = 0. ++ */ ++ ++ return NULL; ++} ++ ++void omap_pm_dsp_set_min_opp(u8 opp_id) ++{ ++ if (opp_id == 0) { ++ WARN_ON(1); ++ return; ++ } ++ ++ pr_debug("OMAP PM: DSP requests minimum VDD1 OPP to be %d\n", opp_id); ++ ++ /* ++ * ++ * For l-o dev tree, our VDD1 clk is keyed on OPP ID, so we ++ * can just test to see which is higher, the CPU's desired OPP ++ * ID or the DSP's desired OPP ID, and use whichever is ++ * highest. ++ * ++ * In CDP12.14+, the VDD1 OPP custom clock that controls the DSP ++ * rate is keyed on MPU speed, not the OPP ID. So we need to ++ * map the OPP ID to the MPU speed for use with clk_set_rate() ++ * if it is higher than the current OPP clock rate. ++ * ++ */ ++} ++ ++ ++u8 omap_pm_dsp_get_opp(void) ++{ ++ pr_debug("OMAP PM: DSP requests current DSP OPP ID\n"); ++ ++ /* ++ * For l-o dev tree, call clk_get_rate() on VDD1 OPP clock ++ * ++ * CDP12.14+: ++ * Call clk_get_rate() on the OPP custom clock, map that to an ++ * OPP ID using the tables defined in board-*.c/chip-*.c files. ++ */ ++ ++ return 0; ++} ++ ++/* ++ * CPUFreq-originated constraint ++ * ++ * In the future, this should be handled by custom OPP clocktype ++ * functions. ++ */ ++ ++struct cpufreq_frequency_table **omap_pm_cpu_get_freq_table(void) ++{ ++ pr_debug("OMAP PM: CPUFreq request for frequency table\n"); ++ ++ /* ++ * Return CPUFreq frequency table here: loop over ++ * all VDD1 clkrates, pull out the mpu_ck frequencies, build ++ * table ++ */ ++ ++ return NULL; ++} ++ ++void omap_pm_cpu_set_freq(unsigned long f) ++{ ++ if (f == 0) { ++ WARN_ON(1); ++ return; ++ } ++ ++ pr_debug("OMAP PM: CPUFreq requests CPU frequency to be set to %lu\n", ++ f); ++ ++ /* ++ * For l-o dev tree, determine whether MPU freq or DSP OPP id ++ * freq is higher. Find the OPP ID corresponding to the ++ * higher frequency. Call clk_round_rate() and clk_set_rate() ++ * on the OPP custom clock. ++ * ++ * CDP should just be able to set the VDD1 OPP clock rate here. ++ */ ++} ++ ++unsigned long omap_pm_cpu_get_freq(void) ++{ ++ pr_debug("OMAP PM: CPUFreq requests current CPU frequency\n"); ++ ++ /* ++ * Call clk_get_rate() on the mpu_ck. ++ */ ++ ++ return 0; ++} ++ ++/* ++ * Powerdomain usecounting hooks ++ */ ++ ++void omap_pm_pwrdm_active(struct powerdomain *pwrdm) ++{ ++ if (!pwrdm) { ++ WARN_ON(1); ++ return; ++ }; ++ ++ pr_debug("OMAP PM: powerdomain %s is becoming active\n", pwrdm->name); ++ ++ /* ++ * CDP code apparently will need these for the enable_power_domain() ++ * and disable_power_domain() functions. ++ */ ++} ++ ++void omap_pm_pwrdm_inactive(struct powerdomain *pwrdm) ++{ ++ if (!pwrdm) { ++ WARN_ON(1); ++ return; ++ }; ++ ++ pr_debug("OMAP PM: powerdomain %s is becoming inactive\n", ++ pwrdm->name); ++ ++ /* ++ * CDP code apparently will need these for the enable_power_domain() ++ * and disable_power_domain() functions. ++ */ ++} ++ ++/* ++ * Should be called before clk framework since clk fw will call ++ * omap_pm_pwrdm_{in,}active() ++ */ ++int __init omap_pm_if_early_init(void) ++{ ++ return 0; ++} ++ ++/* Must be called after clock framework is initialized */ ++int __init omap_pm_if_init(struct omap_opp *mpu_opp_table, ++ struct omap_opp *dsp_opp_table) ++{ ++ mpu_opps = mpu_opp_table; ++ dsp_opps = dsp_opp_table; ++ return 0; ++} ++ ++void omap_pm_if_exit(void) ++{ ++ /* Deallocate CPUFreq frequency table here */ ++} ++ +diff --git a/include/asm-arm/arch-omap/omap-pm.h b/include/asm-arm/arch-omap/omap-pm.h +new file mode 100644 +index 0000000..d272dba +--- /dev/null ++++ b/include/asm-arm/arch-omap/omap-pm.h +@@ -0,0 +1,300 @@ ++/* ++ * omap-pm.h - OMAP power management interface ++ * ++ * Copyright (C) 2008 Texas Instruments, Inc. ++ * Copyright (C) 2008 Nokia Corporation ++ * Paul Walmsley ++ * ++ * Interface developed by (in alphabetical order): Karthik Dasu, Jouni ++ * Högander, Tony Lindgren, Rajendra Nayak, Sakari Poussa, ++ * Veeramanikandan Raju, Anand Sawant, Igor Stoppa, Paul Walmsley, ++ * Richard Woodruff ++ */ ++ ++#ifndef ASM_ARM_ARCH_OMAP_OMAP_PM_H ++#define ASM_ARM_ARCH_OMAP_OMAP_PM_H ++ ++#include <linux/device.h> ++#include <linux/cpufreq.h> ++ ++#include "powerdomain.h" ++ ++/** ++ * struct omap_opp - clock frequency-to-OPP ID table for DSP, MPU ++ * @rate: target clock rate ++ * @opp_id: OPP ID ++ * @min_vdd: minimum VDD1 voltage (in millivolts) for this OPP ++ * ++ * Operating performance point data. Can vary by OMAP chip and board. ++ */ ++struct omap_opp { ++ unsigned long rate; ++ u8 opp_id; ++ u16 min_vdd; ++}; ++ ++/* ++ * agent_id values for use with omap_pm_set_min_bus_tput(): ++ * ++ * OCP_INITIATOR_AGENT is only valid for devices that can act as ++ * initiators -- it represents the device's L3 interconnect ++ * connection. OCP_TARGET_AGENT represents the device's L4 ++ * interconnect connection. ++ */ ++#define OCP_TARGET_AGENT 1 ++#define OCP_INITIATOR_AGENT 2 ++ ++/** ++ * omap_pm_if_early_init - OMAP PM init code called before clock fw init ++ * ++ * Initialize anything that must be configured before the clock ++ * framework starts. The "_if_" is to avoid name collisions with the ++ * PM idle-loop code. ++ */ ++int __init omap_pm_if_early_init(void); ++ ++/** ++ * omap_pm_if_init - OMAP PM init code called after clock fw init ++ * @mpu_opp_table: array ptr to struct omap_opp for MPU ++ * @dsp_opp_table: array ptr to struct omap_opp for DSP ++ * ++ * The main initialization code. OPP tables are passed in here. The ++ * "_if_" is to avoid name collisions with the PM idle-loop code. ++ */ ++int __init omap_pm_if_init(struct omap_opp *mpu_opp_table, ++ struct omap_opp *dsp_opp_table); ++ ++/** ++ * omap_pm_if_exit - OMAP PM exit code ++ * ++ * Exit code; currently unused. The "_if_" is to avoid name ++ * collisions with the PM idle-loop code. ++ */ ++void omap_pm_if_exit(void); ++ ++/* ++ * Device-driver-originated constraints (via board-*.c files, platform_data) ++ */ ++ ++ ++/** ++ * omap_pm_set_max_mpu_wakeup_lat - set the maximum MPU wakeup latency ++ * @dev: struct device * requesting the constraint ++ * @t: maximum MPU wakeup latency in microseconds ++ * ++ * Request that the maximum interrupt latency for the MPU to be no ++ * greater than 't' microseconds. "Interrupt latency" in this case is ++ * defined as the elapsed time from the occurrence of a hardware or ++ * timer interrupt to the time when the device driver's interrupt ++ * service routine has been entered by the MPU. ++ * ++ * It is intended that underlying PM code will use this information to ++ * determine what power state to put the MPU powerdomain into, and ++ * possibly the CORE powerdomain as well, since interrupt handling ++ * code currently runs from SDRAM. Advanced PM or board*.c code may ++ * also configure interrupt controller priorities, OCP bus priorities, ++ * CPU speed(s), etc. ++ * ++ * This function will not affect device wakeup latency, e.g., time ++ * elapsed from when a device driver enables a hardware device with ++ * clk_enable(), to when the device is ready for register access or ++ * other use. To control this device wakeup latency, use ++ * set_max_dev_wakeup_lat() ++ * ++ * Multiple calls to set_max_mpu_wakeup_lat() will replace the ++ * previous t value. To remove the latency target for the MPU, call ++ * with t = -1. ++ * ++ * No return value. ++ */ ++void omap_pm_set_max_mpu_wakeup_lat(struct device *dev, long t); ++ ++ ++/** ++ * omap_pm_set_min_bus_tput - set minimum bus throughput needed by device ++ * @dev: struct device * requesting the constraint ++ * @tbus_id: interconnect to operate on (OCP_{INITIATOR,TARGET}_AGENT) ++ * @r: minimum throughput (in KiB/s) ++ * ++ * Request that the minimum data throughput on the OCP interconnect ++ * attached to device 'dev' interconnect agent 'tbus_id' be no less ++ * than 'r' KiB/s. ++ * ++ * It is expected that the OMAP PM or bus code will use this ++ * information to set the interconnect clock to run at the lowest ++ * possible speed that satisfies all current system users. The PM or ++ * bus code will adjust the estimate based on its model of the bus, so ++ * device driver authors should attempt to specify an accurate ++ * quantity for their device use case, and let the PM or bus code ++ * overestimate the numbers as necessary to handle request/response ++ * latency, other competing users on the system, etc. On OMAP2/3, if ++ * a driver requests a minimum L4 interconnect speed constraint, the ++ * code will also need to add an minimum L3 interconnect speed ++ * constraint, ++ * ++ * Multiple calls to set_min_bus_tput() will replace the previous rate ++ * value for this device. To remove the interconnect throughput ++ * restriction for this device, call with r = 0. ++ * ++ * No return value. ++ */ ++void omap_pm_set_min_bus_tput(struct device *dev, u8 agent_id, unsigned long r); ++ ++ ++/** ++ * omap_pm_set_max_dev_wakeup_lat - set the maximum device enable latency ++ * @dev: struct device * ++ * @t: maximum device wakeup latency in microseconds ++ * ++ * Request that the maximum amount of time necessary for a device to ++ * become accessible after its clocks are enabled should be no greater ++ * than 't' microseconds. Specifically, this represents the time from ++ * when a device driver enables device clocks with clk_enable(), to ++ * when the register reads and writes on the device will succeed. ++ * This function should be called before clk_disable() is called, ++ * since the power state transition decision may be made during ++ * clk_disable(). ++ * ++ * It is intended that underlying PM code will use this information to ++ * determine what power state to put the powerdomain enclosing this ++ * device into. ++ * ++ * Multiple calls to set_max_dev_wakeup_lat() will replace the ++ * previous wakeup latency values for this device. To remove the wakeup ++ * latency restriction for this device, call with t = -1. ++ * ++ * No return value. ++ */ ++void omap_pm_set_max_dev_wakeup_lat(struct device *dev, long t); ++ ++ ++/** ++ * omap_pm_set_max_sdma_lat - set the maximum system DMA transfer start latency ++ * @dev: struct device * ++ * @t: maximum DMA transfer start latency in microseconds ++ * ++ * Request that the maximum system DMA transfer start latency for this ++ * device 'dev' should be no greater than 't' microseconds. "DMA ++ * transfer start latency" here is defined as the elapsed time from ++ * when a device (e.g., McBSP) requests that a system DMA transfer ++ * start or continue, to the time at which data starts to flow into ++ * that device from the system DMA controller. ++ * ++ * It is intended that underlying PM code will use this information to ++ * determine what power state to put the CORE powerdomain into. ++ * ++ * Since system DMA transfers may not involve the MPU, this function ++ * will not affect MPU wakeup latency. Use set_max_cpu_lat() to do ++ * so. Similarly, this function will not affect device wakeup latency ++ * -- use set_max_dev_wakeup_lat() to affect that. ++ * ++ * Multiple calls to set_max_sdma_lat() will replace the previous t ++ * value for this device. To remove the maximum DMA latency for this ++ * device, call with t = -1. ++ * ++ * No return value. ++ */ ++void omap_pm_set_max_sdma_lat(struct device *dev, long t); ++ ++ ++/* ++ * DSP Bridge-specific constraints ++ */ ++ ++/** ++ * omap_pm_dsp_get_opp_table - get OPP->DSP clock frequency table ++ * ++ * Intended for use by DSPBridge. Returns an array of OPP->DSP clock ++ * frequency entries. The final item in the array should have .rate = ++ * .opp_id = 0. ++ */ ++const struct omap_opp *omap_pm_dsp_get_opp_table(void); ++ ++/** ++ * omap_pm_dsp_set_min_opp - receive desired OPP target ID from DSP Bridge ++ * @opp_id: target DSP OPP ID ++ * ++ * Set a minimum OPP ID for the DSP. This is intended to be called ++ * only from the DSP Bridge MPU-side driver. Unfortunately, the only ++ * information that code receives from the DSP/BIOS load estimator is the ++ * target OPP ID; hence, this interface. No return value. ++ */ ++void omap_pm_dsp_set_min_opp(u8 opp_id); ++ ++/** ++ * omap_pm_dsp_get_opp - report the current DSP OPP ID ++ * ++ * Report the current OPP for the DSP. Since on OMAP3, the DSP and ++ * MPU share a single voltage domain, the OPP ID returned back may ++ * represent a higher DSP speed than the OPP requested via ++ * omap_pm_dsp_set_min_opp(). ++ * ++ * Returns the current VDD1 OPP ID, or 0 upon error. ++ */ ++u8 omap_pm_dsp_get_opp(void); ++ ++ ++/* ++ * CPUFreq-originated constraint ++ * ++ * In the future, this should be handled by custom OPP clocktype ++ * functions. ++ */ ++ ++/** ++ * omap_pm_cpu_get_freq_table - return a cpufreq_frequency_table array ptr ++ * ++ * Provide a frequency table usable by CPUFreq for the current chip/board. ++ * Returns a pointer to a struct cpufreq_frequency_table array or NULL ++ * upon error. ++ */ ++struct cpufreq_frequency_table **omap_pm_cpu_get_freq_table(void); ++ ++/** ++ * omap_pm_cpu_set_freq - set the current minimum MPU frequency ++ * @f: MPU frequency in Hz ++ * ++ * Set the current minimum CPU frequency. The actual CPU frequency ++ * used could end up higher if the DSP requested a higher OPP. ++ * Intended to be called by plat-omap/cpu_omap.c:omap_target(). No ++ * return value. ++ */ ++void omap_pm_cpu_set_freq(unsigned long f); ++ ++/** ++ * omap_pm_cpu_get_freq - report the current CPU frequency ++ * ++ * Returns the current MPU frequency, or 0 upon error. ++ */ ++unsigned long omap_pm_cpu_get_freq(void); ++ ++ ++/* ++ * Powerdomain usecounting hooks ++ */ ++ ++/** ++ * omap_pm_pwrdm_active - indicate that a power domain has become active ++ * @pwrdm: struct powerdomain * ++ * ++ * Notify the OMAP PM layer that the power domain 'pwrdm' has become active, ++ * presumably due to a device driver enabling an underlying clock. This ++ * function is intended to be called by a clockdomain node in the clock ++ * framework. No return value. ++ */ ++void omap_pm_pwrdm_active(struct powerdomain *pwrdm); ++ ++ ++/** ++ * omap_pm_pwrdm_inactive - indicate that a power domain has become inactive ++ * @pwrdm: struct powerdomain * ++ * ++ * Notify the OMAP PM layer that the power domain 'pwrdm' has become ++ * inactive, presumably due to a device driver disabling an underlying ++ * clock. This function is intended to be called by a clockdomain ++ * node in the clock framework. No return value. ++ */ ++void omap_pm_pwrdm_inactive(struct powerdomain *pwrdm); ++ ++ ++#endif + + +-- +To unsubscribe from this list: send the line "unsubscribe linux-omap" in +the body of a message to majordomo@vger.kernel.org +More majordomo info at http://vger.kernel.org/majordomo-info.html + +--- /tmp/io.c 2008-08-11 15:29:32.000000000 +0200 ++++ git/arch/arm/mach-omap2/io.c 2008-08-11 15:30:20.083198000 +0200 +@@ -38,6 +38,8 @@ + #include <asm/arch/clockdomain.h> + #include "clockdomains.h" + ++#include <asm/arch/omap-pm.h> ++ + /* + * The machine specific code may provide the extra mapping besides the + * default mapping provided here. +@@ -197,9 +199,11 @@ + void __init omap2_init_common_hw(struct omap_sdrc_params *sp) + { + omap2_mux_init(); ++ omap_pm_if_early_init(); + pwrdm_init(powerdomains_omap); + clkdm_init(clockdomains_omap, clkdm_pwrdm_autodeps); + omap2_clk_init(); ++ omap_pm_if_init(NULL, NULL); + omap2_sdrc_init(sp); + gpmc_init(); + } |