diff options
Diffstat (limited to 'packages/uboot/u-boot-mkimage-gta01-native/nand-dynamic_partitions.patch')
| -rw-r--r-- | packages/uboot/u-boot-mkimage-gta01-native/nand-dynamic_partitions.patch | 354 |
1 files changed, 0 insertions, 354 deletions
diff --git a/packages/uboot/u-boot-mkimage-gta01-native/nand-dynamic_partitions.patch b/packages/uboot/u-boot-mkimage-gta01-native/nand-dynamic_partitions.patch deleted file mode 100644 index ecce004ca6..0000000000 --- a/packages/uboot/u-boot-mkimage-gta01-native/nand-dynamic_partitions.patch +++ /dev/null @@ -1,354 +0,0 @@ -This patch adds support for 'dynamic partitions'. This basically -works as follows: -* The nand code generates a bad-block-table at the first scan of the chip -* The dynamic partition code calculates the raw partition sizes based on - the bad block table. E.g. if you have a partition of size 0x30000, and there are - two bad blocks (0x4000 each) in it, the raw size will increase to 0x38000, and the - following partitions get shifted towards the end of flash. - -Please note that currently the desired partition sizes are stored at compile-time -in an array in drivers/nand/nand_bbt.c, so this definitely needs to change before -submitting/merging upstream. - -In order to calculate the partiton map (and set mtdparts accordingly), you can use -the 'dynpart' command at the prompt. Use 'saveenv' to make the setting permanent. - -Signed-off-by: Harald Welte <laforge@openmoko.org> - -Index: u-boot/drivers/nand/nand_bbt.c -=================================================================== ---- u-boot.orig/drivers/nand/nand_bbt.c -+++ u-boot/drivers/nand/nand_bbt.c -@@ -1044,9 +1044,86 @@ - switch ((int)res) { - case 0x00: return 0; - case 0x01: return 1; -+ case 0x03: return 1; - case 0x02: return allowbbt ? 0 : 1; - } - return 1; - } - -+#if defined(CONFIG_NAND_DYNPART) -+ -+extern unsigned int dynpart_size[]; -+extern char *dynpart_names[]; -+ -+#define MTDPARTS_MAX_SIZE 512 -+ -+ -+static int skip_offs(const struct nand_chip *this, unsigned int offs) -+{ -+ int block = (int) (offs >> (this->bbt_erase_shift - 1)); -+ u_int8_t bbt = (this->bbt[block >> 3] >> (block & 0x06)) & 0x03; -+ -+ return bbt == 3; -+} -+ -+int nand_create_mtd_dynpart(struct mtd_info *mtd) -+{ -+ struct nand_chip *this = mtd->priv; -+ int part; -+ char *mtdparts; -+ unsigned int cur_offs = 0; -+ -+ mtdparts = malloc(MTDPARTS_MAX_SIZE); /* FIXME: bounds checking */ -+ if (!mtdparts) -+ return -ENOMEM; -+ -+ sprintf(mtdparts, "mtdparts=" CFG_NAND_DYNPART_MTD_KERNEL_NAME ":"); -+ -+ for (part = 0; dynpart_size[part] != 0; part++) { -+ unsigned int bb_delta = 0; -+ unsigned int offs = 0; -+ char mtdpart[32]; -+ -+ for (offs = cur_offs; -+ offs < cur_offs + dynpart_size[part] + bb_delta; -+ offs += mtd->erasesize) { -+ if (skip_offs(this, offs)) -+ bb_delta += mtd->erasesize; -+ } -+ -+ /* -+ * Absorb bad blocks immediately following this partition also -+ * into the partition, in order to make next partition start -+ * with a good block. This simplifies handling of the -+ * environment partition. -+ */ -+ while (offs < this->chipsize && skip_offs(this, offs)) { -+ bb_delta += mtd->erasesize; -+ offs += mtd->erasesize; -+ } -+ -+ if (cur_offs + dynpart_size[part] + bb_delta > this->chipsize) -+ dynpart_size[part] = this->chipsize - cur_offs - bb_delta; -+#if 0 -+ printf("partition %u: start = 0x%08x, end=%08x size=%08x, size_inc_bb=%08x\n", -+ part, cur_offs, cur_offs + dynpart_size[part] + bb_delta, -+ dynpart_size[part], dynpart_size[part] + bb_delta); -+#endif -+ cur_offs += dynpart_size[part] + bb_delta; -+ sprintf(mtdpart, "0x%.8x(%.16s),", dynpart_size[part] + bb_delta, -+ dynpart_names[part]); -+ mtdpart[sizeof(mtdpart)-1] = '\0'; -+ strncat(mtdparts, mtdpart, -+ MTDPARTS_MAX_SIZE-strlen(mtdparts)-1); -+ } -+ -+ mtdparts[strlen(mtdparts)-1] = '\0'; -+ printf("mtdparts %s\n", mtdparts); -+ setenv("mtdparts", mtdparts); -+ -+ free(mtdparts); -+ return 0; -+} -+#endif /* CONFIG_NAND_DYNPART */ -+ - #endif -Index: u-boot/include/configs/neo1973_gta01.h -=================================================================== ---- u-boot.orig/include/configs/neo1973_gta01.h -+++ u-boot/include/configs/neo1973_gta01.h -@@ -99,7 +99,7 @@ - CFG_CMD_ELF | \ - CFG_CMD_MISC | \ - /* CFG_CMD_USB | */ \ -- /* CFG_CMD_JFFS2 | */ \ -+ CFG_CMD_JFFS2 | \ - CFG_CMD_DIAG | \ - /* CFG_CMD_HWFLOW | */ \ - CFG_CMD_SAVES | \ -@@ -212,13 +212,13 @@ - #define CONFIG_FAT 1 - #define CONFIG_SUPPORT_VFAT - --#if 0 -+#if 1 - /* JFFS2 driver */ - #define CONFIG_JFFS2_CMDLINE 1 - #define CONFIG_JFFS2_NAND 1 - #define CONFIG_JFFS2_NAND_DEV 0 --#define CONFIG_JFFS2_NAND_OFF 0x634000 --#define CONFIG_JFFS2_NAND_SIZE 0x39cc000 -+//#define CONFIG_JFFS2_NAND_OFF 0x634000 -+//#define CONFIG_JFFS2_NAND_SIZE 0x39cc000 - #endif - - /* ATAG configuration */ -@@ -257,4 +257,9 @@ - - #define CONFIG_DRIVER_PCF50606 1 - -+#define MTDIDS_DEFAULT "nand0=neo1973-nand" -+#define MTPARTS_DEFAULT "neo1973-nand:256k(u-boot),16k(u-boot_env),2M(kernel),640k(splash),-(jffs2)" -+#define CFG_NAND_DYNPART_MTD_KERNEL_NAME "neo1973-nand" -+#define CONFIG_NAND_DYNPART -+ - #endif /* __CONFIG_H */ -Index: u-boot/common/cmd_jffs2.c -=================================================================== ---- u-boot.orig/common/cmd_jffs2.c -+++ u-boot/common/cmd_jffs2.c -@@ -1841,6 +1841,29 @@ - return NULL; - } - -+/* Return the 'net size' of the partition (i.e. excluding any bad blocks) */ -+unsigned int nand_net_part_size(struct part_info *part) -+{ -+ struct mtd_info *mtd; -+ unsigned int offs; -+ unsigned int bb_delta = 0; -+ -+ if (!part || !part->dev || !part->dev->id || -+ part->dev->id->num >= CFG_MAX_NAND_DEVICE) -+ return 0; -+ -+ mtd = &nand_info[part->dev->id->num]; -+ -+ for (offs = part->offset; offs < part->offset + part->size; -+ offs += mtd->erasesize) { -+ if (nand_isbad_bbt(mtd, offs, 0)) -+ bb_delta += mtd->erasesize; -+ } -+ -+ return part->size - bb_delta; -+} -+ -+ - /***************************************************/ - /* U-boot commands */ - /***************************************************/ -@@ -2132,6 +2155,24 @@ - printf ("Usage:\n%s\n", cmdtp->usage); - return 1; - } -+ -+#if defined(CONFIG_NAND_DYNPART) -+extern int nand_create_mtd_dynpart(struct mtd_info *mtd); -+ -+int do_dynpart(cmd_tbl_t *cmdtp, int flag, int argc, char *argv[]) -+{ -+#if 0 -+ int i = simple_strtoul(argv[1], NULL, 0); -+ if (i >= CFG_MAX_NAND_DEVICE) -+ return -EINVAL; -+#endif -+ nand_create_mtd_dynpart(&nand_info[0]); -+ -+ return 0; -+} -+#endif /* CONFIG_NAND_DYNPART */ -+ -+ - #endif /* #ifdef CONFIG_JFFS2_CMDLINE */ - - /***************************************************/ -@@ -2197,6 +2238,15 @@ - "<name> := '(' NAME ')'\n" - "<ro-flag> := when set to 'ro' makes partition read-only (not used, passed to kernel)\n" - ); -+ -+#if defined(CONFIG_NAND_DYNPART) -+U_BOOT_CMD( -+ dynpart, 1, 1, do_dynpart, -+ "dynpart\t- dynamically calculate partition table based on BBT\n", -+ "\n" -+ " - sets 'mtdparts' according to BBT\n"); -+#endif /* CONFIG_NAND_DYNPART */ -+ - #endif /* #ifdef CONFIG_JFFS2_CMDLINE */ - - /***************************************************/ -Index: u-boot/common/cmd_nand.c -=================================================================== ---- u-boot.orig/common/cmd_nand.c -+++ u-boot/common/cmd_nand.c -@@ -101,7 +101,7 @@ - } - - int --arg_off_size(int argc, char *argv[], nand_info_t *nand, ulong *off, ulong *size) -+arg_off_size(int argc, char *argv[], nand_info_t *nand, ulong *off, ulong *size, int net) - { - int idx = nand_curr_device; - #if (CONFIG_COMMANDS & CFG_CMD_JFFS2) && defined(CONFIG_JFFS2_CMDLINE) -@@ -122,10 +122,17 @@ - printf("'%s' is not a number\n", argv[1]); - return -1; - } -- if (*size > part->size) -- *size = part->size; -+ if (*size > part->size) { -+ if (net) -+ *size = nand_net_part_size(part); -+ else -+ *size = part->size; -+ } - } else { -- *size = part->size; -+ if (net) -+ *size = nand_net_part_size(part); -+ else -+ *size = part->size; - } - idx = dev->id->num; - *nand = nand_info[idx]; -@@ -261,7 +268,7 @@ - - printf("\nNAND %s: ", scrub ? "scrub" : "erase"); - /* skip first two or three arguments, look for offset and size */ -- if (arg_off_size(argc - o, argv + o, nand, &off, &size) != 0) -+ if (arg_off_size(argc - o, argv + o, nand, &off, &size, 0) != 0) - return 1; - - memset(&opts, 0, sizeof(opts)); -@@ -323,7 +330,7 @@ - - read = strncmp(cmd, "read", 4) == 0; /* 1 = read, 0 = write */ - printf("\nNAND %s: ", read ? "read" : "write"); -- if (arg_off_size(argc - 3, argv + 3, nand, &off, &size) != 0) -+ if (arg_off_size(argc - 3, argv + 3, nand, &off, &size, 1) != 0) - return 1; - - s = strchr(cmd, '.'); -@@ -445,7 +452,7 @@ - } - - if (strcmp(cmd, "unlock") == 0) { -- if (arg_off_size(argc - 2, argv + 2, nand, &off, &size) < 0) -+ if (arg_off_size(argc - 2, argv + 2, nand, &off, &size, 0) < 0) - return 1; - - if (!nand_unlock(nand, off, size)) { -Index: u-boot/common/cmd_dynenv.c -=================================================================== ---- u-boot.orig/common/cmd_dynenv.c -+++ u-boot/common/cmd_dynenv.c -@@ -60,7 +60,7 @@ - buf[2] = 'V'; - buf[3] = '0'; - -- if (arg_off_size(argc-2, argv+2, mtd, &addr, &dummy) < 0) { -+ if (arg_off_size(argc-2, argv+2, mtd, &addr, &dummy, 1) < 0) { - printf("Offset or partition name expected\n"); - goto fail; - } -Index: u-boot/include/util.h -=================================================================== ---- u-boot.orig/include/util.h -+++ u-boot/include/util.h -@@ -28,6 +28,6 @@ - - /* common/cmd_nand.c */ - int arg_off_size(int argc, char *argv[], nand_info_t *nand, ulong *off, -- ulong *size); -+ ulong *size, int net); - - #endif /* UTIL_H */ -Index: u-boot/board/qt2410/qt2410.c -=================================================================== ---- u-boot.orig/board/qt2410/qt2410.c -+++ u-boot/board/qt2410/qt2410.c -@@ -126,3 +126,9 @@ - - return 0; - } -+ -+unsigned int dynpart_size[] = { -+ CFG_UBOOT_SIZE, 0x4000, 0x200000, 0xa0000, 0x3d5c000-CFG_UBOOT_SIZE, 0 }; -+char *dynpart_names[] = { -+ "u-boot", "u-boot_env", "kernel", "splash", "rootfs", NULL }; -+ -Index: u-boot/board/neo1973/gta01/gta01.c -=================================================================== ---- u-boot.orig/board/neo1973/gta01/gta01.c -+++ u-boot/board/neo1973/gta01/gta01.c -@@ -429,3 +434,14 @@ - return 0; - } - -+ -+/* The sum of all part_size[]s must equal to the NAND size, i.e., 0x4000000. -+ "initrd" is sized such that it can hold two uncompressed 16 bit 640*480 -+ images: 640*480*2*2 = 1228800 < 1245184. */ -+ -+unsigned int dynpart_size[] = { -+ CFG_UBOOT_SIZE, 0x4000, 0x200000, 0xa0000, 0x3d5c000-CFG_UBOOT_SIZE, 0 }; -+char *dynpart_names[] = { -+ "u-boot", "u-boot_env", "kernel", "splash", "rootfs", NULL }; -+ -+ -Index: u-boot/include/configs/qt2410.h -=================================================================== ---- u-boot.orig/include/configs/qt2410.h -+++ u-boot/include/configs/qt2410.h -@@ -283,5 +283,7 @@ - - #define MTDIDS_DEFAULT "nand0=qt2410-nand" - #define MTPARTS_DEFAULT "qt2410-nand:192k(u-boot),8k(u-boot_env),2M(kernel),2M(splash),-(jffs2)" -+#define CFG_NAND_DYNPART_MTD_KERNEL_NAME "qt2410-nand" -+#define CONFIG_NAND_DYNPART - - #endif /* __CONFIG_H */ |