diff options
Diffstat (limited to 'packages/nslu2-binary-only/unslung-rootfs-2.3r63/README')
| -rw-r--r-- | packages/nslu2-binary-only/unslung-rootfs-2.3r63/README | 284 |
1 files changed, 284 insertions, 0 deletions
diff --git a/packages/nslu2-binary-only/unslung-rootfs-2.3r63/README b/packages/nslu2-binary-only/unslung-rootfs-2.3r63/README new file mode 100644 index 0000000000..f4ffe4d29b --- /dev/null +++ b/packages/nslu2-binary-only/unslung-rootfs-2.3r63/README @@ -0,0 +1,284 @@ +Unslung-6.x Family Release README INSTALLATION + +You must follow the steps in this README *exactly*. Do not skip any steps, and +do not skip ahead thinking you know what you are doing and don't need to follow +instructions step by step. + +If at any time you have any questions concerning the installation or operation +of Unslung firmware, your first port of call should be the NSLU2-Linux wiki at: + + http://www.nslu2-linux.org + +If you are looking for further Unslung notes - including ipkg usage, diversion +script details, or ChangeLog information, please consult the associated NOTES +file. + +------------------------------------------------------------------------------- + +There are three parts to completing the installation of the Unslung firmware: + + 1 - PRE-INSTALLATION CONSIDERATIONS + 2 - FIRMWARE INSTALLATION DETAILS + 3 - UNSLINGING DETAILS + + +PRE-INSTALLATION CONSIDERATIONS + +1) You *must* test telnet Redboot access first before you flash the Unslung + firmware. Failure to do so will mean you get no sympathy at all if you + can't access Redboot when you need to recover from a bad flash. See + + http://www.nslu2-linux.org/wiki/HowTo/TelnetIntoRedBoot + + - Redboot is the bootloader that runs when the device is first started, + loading things into memory and starting Linux. By testing your + ability to telnet into Redboot, you are ensuring that if you injure + your NSLU2 with a bad flash you should be able to follow the "How + To Recover From A Bad Flash" instructions at + + http://www.nslu2-linux.org/wiki/HowTo/RecoverFromABadFlash + +2) If you want to install any packages, then you must have an external disk. + It is possible to make changes to the root filesystem in the internal + flash storage, but the space is very limited. In fact, just running + "ipkg update" on an NSLU2 which does not have an external disk attached + will most likely render the NSLU2 unusable due to filling up the flash (if + this happens then you will need to follow the recovery instructions in + the previous step). So unless you are an expert, then use an external + disk. + +3) The external disk that you use as the target for package installation must + be (or have previously been) formatted by the NSLU2. It is possible to + upgrade from all previous Unslung versions without reformatting your disk. + The unsling script will not touch anything in /unslung or /opt on your + disk, so make sure all your file modifications are in those directories, + as you were warned in the README file in all previous Unslung versions :-) + +4) If you want to use a flash disk as the target for package installation, + ensure that it is at least 256MB, plugged into port 1, and formatted + via the Linksys web interface. + +5) Please verify that any disks you are going to connect to the NSLU2 are + recognized and working properly *before* updating your firmware (including + any shares and data you had previously stored.) If not, DO NOT CONTINUE. + You may want to check out "How To Troubleshoot A Drive Missing Condition" + at: + + http://www.nslu2-linux.org/wiki/HowTo/TroubleshootADriveMissingCondition + + - The only exception to this, of course, are those enclosures that the + stock firmware does not support, but the Unslung firmware does + support. + +6) If you are upgrading your firmware, you should make a configuration backup + via the Linksys web interface. The configuration backup can be found + under "Administration", "Advanced", and then "Backup." The top section of + that webpage is titled "Config Backup" and "Download" should be used to + save your NSLU2 Users, Groups and Shares setup to a disk file. + + +FIRMWARE INSTALLATION DETAILS + +1) Shutdown the NSLU2, and remove any disks that you may have plugged into the + NSLU2. Power back up the NSLU2. + + - Firmware upgrades must always be performed with *no* hard disks or flash + disks attached. This CANNOT be emphasized enough. Are you sure you + unplugged the disks before powering up? If so, you may continue. + +2) Access the Web interface. Note that you should use the username "admin" and + password "admin" for the web interface at this point (as no disks are + attached, the default username and password is the only way to access the + Management web pages). + + 2-a) If you are installing Unslung 6.x onto an NSLU2 unit with Linksys + standard firmware *or* Unslung version 1.x or version 2.x already + installed, flash unslung-6.x.bin as you normally would flash new + firmware (using the web interface "Upgrade Firmware" page). + + 2-b) If you are installing Unslung 6.x onto an NSLU2 unit with Unslung + version 3.x already installed, you must put the NSLU2 into + maintenance mode before you can use the web interface to flash a new + version. Just click the "Enter Maintenance Mode" link on the web + interface "Upgrade Firmware" page, wait for the NSLU2 to reboot, and + then flash the new firmware in the normal manner (using the web + interface "Upgrade Firmware" page). + + 2-c) If you are installing Unslung 6.x onto an NSLU2 unit with Unslung + version 4.x already installed, you must put the NSLU2 into RedBoot + Upgrade Mode before you can upload new firmware. Note that Unslung + version 4.x has an "Enter Maintenance Mode" link on the web interface + "Upgrade Firmware" page, but it does not work, so you will need to + use the instructions at + + http://www.nslu2-linux.org/wiki/HowTo/TelnetIntoRedBoot + + to access the RedBoot command line, and then type "upgrade" to put + the NSLU2 into RedBoot Upgrade Mode. Then you will need to use the + Linux UpSlug tool or the Windows SerComm Upgrade tool to upload the + new firmware. + + 2-d) If you are installing Unslung 6.x onto an NSLU2 unit with version 5.x + or version 6.x already installed, you must first put the NSLU2 into + RedBoot Upgrade Mode. Just click the "Enter Upgrade Mode" link on the + web interface "Upgrade Firmware" page, wait for the NSLU2 to reboot, + and for the Ready/Status LED to begin flashing red and green, and then + use either the Linux UpSlug tool or the Windows SerComm Upgrade tool + to upload the new firmware. + + - During firmware flashing, the top LED - Ready/Status - flashes red and + green (approximately 5 minutes, but can be much longer). + + - The NSLU2 will reboot after the flashing is complete. + +3) Shutdown the NSLU2 (again), attach disk(s), and power it back up. + +4) Verify your NSLU2 is working normally again at this point in the web + interface. In particular, you should ensure that all your disks are still + recognized as they were before you updated the firmware (including any + shares and data you had previously stored.) If not, DO NOT CONTINUE. + You may want to check out "How To Troubleshoot A Drive Missing Condition" + at: + + http://www.nslu2-linux.org/wiki/HowTo/TroubleshootADriveMissingCondition + + - If you are not "unslinging", you can stop at this point. *HOWEVER!*, + the only reason for not unslinging would be in the case of a re-flash + of the SAME firmware. Even if this is a point firmware upgrade, you + will need to unsling. + + ***** If you do not choose to do the unslinging procedure described below, + DO NOT install packages unless you are SURE you know what you are + doing! "Bricking" your NSLU2 by not unslinging and then running ipkg + is not just a possibility, it is a certainty. + +5) Shutdown the NSLU2 and unplug *ALL* attached disks. + + - You must NOT have any disk plugged into the NSLU2 when you reboot to + perform the next part of installation - the "Unslinging". + + +'UNSLINGING' DETAILS + +"Unslinging" is the process of copying the root filesystem of your NSLU2 onto +an external disk, and configuring that external disk for installation of +packages. Basically it's a script (stored in /sbin/unsling) which copies all +the files from the internal jffs2 filesystem onto the external disk and tells +the internal firmware to load the root filesystem from the external disk when +booting in the future. + +To run the unsling-script you have to be logged in as root (with a telnet +session). + +NOTE: There are two root-passwords. One is saved in a internal file called +/usr/local/passwd (we know this one - it's "uNSLUng" and used when you boot +without a attached harddisk) the other is stored in a external file called +/share/hdd/conf/passwd (we don't know this one - it's used when you boot with a +external harddisk attached). Later in the process you can change both of +them. That means: Everytime you boot WITHOUT a attached harddisk you gain +root-access with the "uNSLUng" password. If you boot WITH an attached harddisk, +you won't have access until you change the file /share/hdd/conf/passwd. + +1) Power up the NSLU2 without any disks connected. + + - This only has to be done when you update the firmware. + + ***** To reiterate, you should not have a disk plugged in at this stage. + If you powered up your NSLU2 with a disk attached, shutdown the + NSLU2, unplug the disks, and power up again. + +2) Enable telnet by going to "http://192.168.1.77/Management/telnet.cgi", and + press the enable button. + + - If you had previously changed the IP address of your NSLU2 from + 192.168.1.77 to something else, then you should use that new IP + address to enable telnet. Again note that you should use the username + "admin" and password "admin" for the web interface at this point (as + no disks are attached, the default username and password is the only + way to access the Management web pages). + + - Make sure you have **** NO DISKS ATTACHED AT THIS TIME **** + + - If you plug a disk in before you complete the telnet connection, then + the NSLU2 will pick up the Linksys password from the disk, and you + will not be able to telnet into it. So don't have any disks attached + at this point. + + - Make sure you have **** NO DISKS ATTACHED AT THIS TIME **** + +3) OK, now that you don't have any disks attached, you can proceed and telnet + into the NSLU2 using the username root and password uNSLUng. + +4) Identify which drive you wish you "unsling", and plug it in. Wait a minute + or two while the disk is mounted. Check the web interface to make sure + that the disk has been recognised by the Linksys software. + + - If the disk has not been previously formatted on the NSLU2, then now is + the time to do that. Make sure that the drive is recognized in the + web interface. + +5) In the telnet session, run "/sbin/unsling disk1" or "/sbin/unsling disk2" + (depending upon whether you want to unsling to a disk connected to the + Disk1 port or the Disk2 port). + + - Once you "unsling" to an external disk on a particular port (Disk 1 or + Disk 2), it is important that you keep that disk continually plugged + into that same port whenever the NSLU2 is turned on. + + ***** Unsling will not change the password on your disk, so if you had + previously changed the password on a disk, then your password will + not be changed. Also note that simply editing the /etc/passwd file + is not enough to permanently change a password. See: + + http://www.nslu2-linux.org/wiki/HowTo/ChangePasswordsFromTheCommandLine + + NOTE: There are two root-passwords. One is saved in a internal + file called /usr/local/passwd (we know this one - it's "uNSLUng" + and used when you boot without a attached harddisk) the other is + stored in a external file called /share/hdd/conf/passwd (we don't + know this one - it's used when you boot with a external harddisk + attached). That means: Everytime you boot WITHOUT a attached harddisk + you gain root-access with the "uNSLUng" password. If you boot + WITH an attached harddisk, you won't have access until you change + the file /share/hdd/conf/passwd. So you should change this file + as soon as you unsling to an external disk, before you exit the + telnet session that you are using to unsling to the disk. + +6) If you wish to migrate your packages from the old Unslung 3.x location in + the /share/hdd/conf (disk1) or /share/flash/conf (disk2) partitions to the + new Unslung 4.x, 5.x and 6.x location on the data partition, then run: + "/sbin/slingover disk1" (if your packages were previously on disk1 and you + ran "/sbin/unsling disk1" in step 5) or "/sbin/slingover disk2" (if your + packages were previously on disk2 and you ran "/sbin/unsling disk2" in + step 5). + + - If your packages were not stored in /share/hdd/conf or /share/flash/conf + (e.g. you had previously moved your packages from the conf partition + to the data partition), then all bets are off and you will need to + read the /sbin/slingover script and perform the appropriate steps + manually. + +7) Reboot. + + ***** DO NOT RUN ipkg BEFORE YOU REBOOT AND CONFIRM EXTERNAL ROOTFS ***** + + - If you were to run ipkg when the root filesystem is loaded from the + internal jffs2 filesystem, then you would fill the flash and cause + your NSLU2 to no longer boot and require reflashing to recover. + +8) Wait for the NSLU2 to boot, telnet in, and confirm that the root filesystem + is being loaded from the external disk. + +***** Congratulations, you're now Unslung! ***** + +Make sure you add an entry to the "The Unslung 6.x" table in the Yahoo group. +Just use the next free integer for your Unslung number. + +If you make no further changes, your NSLU2 will continue to operate normally. +But to customize things, you'll be downloading packages and adding stuff to the +/unslung directory using diversion scripts. + +Read the NOTES file to expand the capabilities of your Unslung NSLU2! + +Enjoy! + |