diff options
Diffstat (limited to 'packages/linux/linux-omap-2.6.28')
| -rw-r--r-- | packages/linux/linux-omap-2.6.28/0001-This-merges-Steve-Kipisz-USB-EHCI-support.-He-star.patch | 146 | ||||
| -rw-r--r-- | packages/linux/linux-omap-2.6.28/beagleboard/defconfig | 6 |
2 files changed, 149 insertions, 3 deletions
diff --git a/packages/linux/linux-omap-2.6.28/0001-This-merges-Steve-Kipisz-USB-EHCI-support.-He-star.patch b/packages/linux/linux-omap-2.6.28/0001-This-merges-Steve-Kipisz-USB-EHCI-support.-He-star.patch new file mode 100644 index 0000000000..d590f8ffb9 --- /dev/null +++ b/packages/linux/linux-omap-2.6.28/0001-This-merges-Steve-Kipisz-USB-EHCI-support.-He-star.patch @@ -0,0 +1,146 @@ +From f8f10f496bce396416d7156da876222c6ce8c341 Mon Sep 17 00:00:00 2001 +From: Steven Kipisz <skipisz@beagleboard.org> +Date: Wed, 9 Jan 2009 12:01:11 -0600 +Subject: [PATCH-USB] Omap3 beagleboard: add support for EHCI in revision C1 boards + +Signed-off-by: Jason Kridner <jkridner@beagleboard.org> +--- + arch/arm/mach-omap2/board-omap3beagle.c | 10 +--------- + arch/arm/mach-omap2/usb-ehci.c | 4 +--- + drivers/usb/host/ehci-omap.c | 26 ++++++++++++++++++++++++++ + 3 files changed, 28 insertions(+), 12 deletions(-) + +diff --git a/arch/arm/mach-omap2/board-omap3beagle.c b/arch/arm/mach-omap2/board-omap3beagle.c +index fe97bab..de81153 100644 +--- a/arch/arm/mach-omap2/board-omap3beagle.c ++++ b/arch/arm/mach-omap2/board-omap3beagle.c +@@ -140,15 +140,7 @@ static int beagle_twl_gpio_setup(struct device *dev, + * power switch and overcurrent detect + */ + +- gpio_request(gpio + 1, "EHCI_nOC"); +- gpio_direction_input(gpio + 1); +- +- /* TWL4030_GPIO_MAX + 0 == ledA, EHCI nEN_USB_PWR (out, active low) */ +- gpio_request(gpio + TWL4030_GPIO_MAX, "nEN_USB_PWR"); +- gpio_direction_output(gpio + TWL4030_GPIO_MAX, 1); +- +- /* TWL4030_GPIO_MAX + 1 == ledB, PMU_STAT (out, active low LED) */ +- gpio_leds[2].gpio = gpio + TWL4030_GPIO_MAX + 1; ++ /* TODO: This needs to be modified to not rely on u-boot */ + + return 0; + } +diff --git a/arch/arm/mach-omap2/usb-ehci.c b/arch/arm/mach-omap2/usb-ehci.c +index 489439d..2c6305b 100644 +--- a/arch/arm/mach-omap2/usb-ehci.c ++++ b/arch/arm/mach-omap2/usb-ehci.c +@@ -152,9 +152,7 @@ static void setup_ehci_io_mux(void) + void __init usb_ehci_init(void) + { + #if defined(CONFIG_USB_EHCI_HCD) || defined(CONFIG_USB_EHCI_HCD_MODULE) +- /* Setup Pin IO MUX for EHCI */ +- if (cpu_is_omap34xx()) +- setup_ehci_io_mux(); ++ /* TODO: Setup Pin IO MUX for EHCI - moved this temporarily to U-boot */ + + if (platform_device_register(&ehci_device) < 0) { + printk(KERN_ERR "Unable to register HS-USB (EHCI) device\n"); + +diff --git a/drivers/usb/host/ehci-omap.c b/drivers/usb/host/ehci-omap.c +index 1b3266c..8472996 100644 +--- a/drivers/usb/host/ehci-omap.c ++++ b/drivers/usb/host/ehci-omap.c +@@ -48,16 +48,26 @@ + * to get the PHY state machine in working state + */ + #define EXTERNAL_PHY_RESET ++#ifdef CONFIG_MACH_OMAP3_BEAGLE ++#define EXT_PHY_RESET_GPIO_PORT2 (147) ++#else + #define EXT_PHY_RESET_GPIO_PORT1 (57) + #define EXT_PHY_RESET_GPIO_PORT2 (61) ++#endif + #define EXT_PHY_RESET_DELAY (10) + ++#define PHY_STP_PULLUP_ENABLE (0x10) ++#define PHY_STP_PULLUP_DISABLE (0x90) ++ ++ + /* ISSUE2: + * USBHOST supports External charge pump PHYs only + * Use the VBUS from Port1 to power VBUS of Port2 externally + * So use Port2 as the working ULPI port + */ ++#ifndef CONFIG_MACH_OMAP3_BEAGLE + #define VBUS_INTERNAL_CHARGEPUMP_HACK ++#endif + + #endif /* CONFIG_OMAP_EHCI_PHY_MODE */ + +@@ -225,14 +235,43 @@ static int omap_start_ehc(struct platform_device *dev, struct usb_hcd *hcd) + + #ifdef EXTERNAL_PHY_RESET + /* Refer: ISSUE1 */ ++#ifndef CONFIG_MACH_OMAP3_BEAGLE + gpio_request(EXT_PHY_RESET_GPIO_PORT1, "USB1 PHY reset"); + gpio_direction_output(EXT_PHY_RESET_GPIO_PORT1, 0); ++#endif + gpio_request(EXT_PHY_RESET_GPIO_PORT2, "USB2 PHY reset"); + gpio_direction_output(EXT_PHY_RESET_GPIO_PORT2, 0); ++ gpio_set_value(EXT_PHY_RESET_GPIO_PORT2, 0); + /* Hold the PHY in RESET for enough time till DIR is high */ + udelay(EXT_PHY_RESET_DELAY); + #endif + ++ /* ++ * The PHY register 0x7 - Interface Control register is ++ * configured to disable the integrated STP pull-up resistor ++ * used for interface protection. ++ * ++ * May not need to be here. ++ */ ++ omap_writel((0x7 << EHCI_INSNREG05_ULPI_REGADD_SHIFT) |/* interface reg */ ++ (2 << EHCI_INSNREG05_ULPI_OPSEL_SHIFT) |/* Write */ ++ (1 << EHCI_INSNREG05_ULPI_PORTSEL_SHIFT) |/* Port1 */ ++ (1 << EHCI_INSNREG05_ULPI_CONTROL_SHIFT) |/* Start */ ++ (PHY_STP_PULLUP_DISABLE), ++ EHCI_INSNREG05_ULPI); ++ ++ while (!(omap_readl(EHCI_INSNREG05_ULPI) & (1<<EHCI_INSNREG05_ULPI_CONTROL_SHIFT))); ++ ++ /* Force PHY to HS */ ++ omap_writel((0x4 << EHCI_INSNREG05_ULPI_REGADD_SHIFT) |/* function ctrl */ ++ (2 << EHCI_INSNREG05_ULPI_OPSEL_SHIFT) |/* Write */ ++ (1 << EHCI_INSNREG05_ULPI_PORTSEL_SHIFT) |/* Port1 */ ++ (1 << EHCI_INSNREG05_ULPI_CONTROL_SHIFT) |/* Start */ ++ (0x40), ++ EHCI_INSNREG05_ULPI); ++ ++ while (!(omap_readl(EHCI_INSNREG05_ULPI) & (1<<EHCI_INSNREG05_ULPI_CONTROL_SHIFT))); ++ + /* Configure TLL for 60Mhz clk for ULPI */ + ehci_clocks->usbtll_fck_clk = clk_get(&dev->dev, USBHOST_TLL_FCLK); + if (IS_ERR(ehci_clocks->usbtll_fck_clk)) +@@ -307,7 +346,9 @@ static int omap_start_ehc(struct platform_device *dev, struct usb_hcd *hcd) + * Hold the PHY in RESET for enough time till PHY is settled and ready + */ + udelay(EXT_PHY_RESET_DELAY); ++#ifndef CONFIG_MACH_OMAP3_BEAGLE + gpio_set_value(EXT_PHY_RESET_GPIO_PORT1, 1); ++#endif + gpio_set_value(EXT_PHY_RESET_GPIO_PORT2, 1); + #endif + +@@ -393,7 +434,9 @@ static void omap_stop_ehc(struct platform_device *dev, struct usb_hcd *hcd) + + + #ifdef EXTERNAL_PHY_RESET ++#ifndef CONFIG_MACH_OMAP3_BEAGLE + gpio_free(EXT_PHY_RESET_GPIO_PORT1); ++#endif + gpio_free(EXT_PHY_RESET_GPIO_PORT2); + #endif + +-- +1.6.0.4.790.gaa14a diff --git a/packages/linux/linux-omap-2.6.28/beagleboard/defconfig b/packages/linux/linux-omap-2.6.28/beagleboard/defconfig index 6dcf5fe3aa..4e3dd6edc1 100644 --- a/packages/linux/linux-omap-2.6.28/beagleboard/defconfig +++ b/packages/linux/linux-omap-2.6.28/beagleboard/defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit # Linux kernel version: 2.6.28-omap1 -# Fri Jan 9 12:28:30 2009 +# Fri Jan 9 17:09:12 2009 # CONFIG_ARM=y CONFIG_SYS_SUPPORTS_APM_EMULATION=y @@ -1494,8 +1494,8 @@ CONFIG_USB_MON=y # # CONFIG_USB_C67X00_HCD is not set CONFIG_USB_EHCI_HCD=y -# CONFIG_OMAP_EHCI_PHY_MODE is not set -CONFIG_OMAP_EHCI_TLL_MODE=y +CONFIG_OMAP_EHCI_PHY_MODE=y +# CONFIG_OMAP_EHCI_TLL_MODE is not set CONFIG_USB_EHCI_ROOT_HUB_TT=y # CONFIG_USB_EHCI_TT_NEWSCHED is not set # CONFIG_USB_ISP116X_HCD is not set |