summaryrefslogtreecommitdiff
path: root/packages/nslu2-binary-only
diff options
context:
space:
mode:
authorMike Westerhof <mwester@dls.net>2006-04-06 03:39:05 +0000
committerOpenEmbedded Project <openembedded-devel@lists.openembedded.org>2006-04-06 03:39:05 +0000
commit2b1e71a99eb85c82e4f5fbe16ad7d99ca250072a (patch)
treef83f8f31b4f55bc9c1d5984b77c09a9813553a06 /packages/nslu2-binary-only
parent204bcb2d7913b9bd58f8b38a78685fd15f68b48c (diff)
Unslung: README firmware flashing procedure updated
Diffstat (limited to 'packages/nslu2-binary-only')
-rw-r--r--packages/nslu2-binary-only/unslung-rootfs-2.3r63/README75
1 files changed, 37 insertions, 38 deletions
diff --git a/packages/nslu2-binary-only/unslung-rootfs-2.3r63/README b/packages/nslu2-binary-only/unslung-rootfs-2.3r63/README
index 9e34a42820..27dddeafbf 100644
--- a/packages/nslu2-binary-only/unslung-rootfs-2.3r63/README
+++ b/packages/nslu2-binary-only/unslung-rootfs-2.3r63/README
@@ -148,44 +148,43 @@ FIRMWARE INSTALLATION DETAILS
Management web pages).
2-a) If you are installing Unslung 6.x onto an NSLU2 unit with Linksys
- standard firmware *or* Unslung version 1.x or version 2.x already
- installed, flash unslung-6.x.bin as you normally would flash new
- firmware (using the web interface "Upgrade Firmware" page).
-
- 2-b) If you are installing Unslung 6.x onto an NSLU2 unit with Unslung
- version 3.x already installed, you must put the NSLU2 into
- maintenance mode before you can use the web interface to flash a new
- version. Just click the "Enter Maintenance Mode" link on the web
- interface "Upgrade Firmware" page, wait for the NSLU2 to reboot, and
- then flash the new firmware in the normal manner (using the web
- interface "Upgrade Firmware" page).
-
- 2-c) If you are installing Unslung 6.x onto an NSLU2 unit with Unslung
- version 4.x already installed, you must put the NSLU2 into RedBoot
- Upgrade Mode before you can upload new firmware. Note that Unslung
- version 4.x has an "Enter Maintenance Mode" link on the web interface
- "Upgrade Firmware" page, but it does not work, so you will need to
- use the instructions at
-
- http://www.nslu2-linux.org/wiki/HowTo/TelnetIntoRedBoot
-
- to access the RedBoot command line, and then type "upgrade" to put
- the NSLU2 into RedBoot Upgrade Mode. Then you will need to use the
- Linux UpSlug2 tool or the Windows SerComm Upgrade tool to upload the
- new firmware.
-
- 2-d) If you are installing Unslung 6.x onto an NSLU2 unit with version 5.x
- or version 6.x already installed, you must first put the NSLU2 into
- RedBoot Upgrade Mode. Just click the "Enter Upgrade Mode" link on the
- web interface "Upgrade Firmware" page, wait for the NSLU2 to reboot,
- and for the Ready/Status LED to begin flashing red and green, and then
- use either the Linux UpSlug2 tool or the Windows SerComm Upgrade tool
- to upload the new firmware.
-
- - During firmware flashing, the top LED - Ready/Status - flashes red and
- green (approximately 5 minutes, but can be much longer).
-
- - The NSLU2 will reboot after the flashing is complete.
+ standard firmware already installed, flash unslung-6.x.bin as you
+ normally would flash new firmware (using the web interface
+ "Upgrade Firmware" page). See your NSLU2 user manual for details
+ if you don't know how to do this.
+
+ - During firmware flashing, the top LED - Ready/Status - flashes
+ red and green (approximately 5 minutes, but can be much longer).
+
+ - The NSLU2 will reboot after the flashing is complete.
+
+ 2-b) If you are installing Unslung 6.x onto an NSLU2 unit with an
+ existing version of nslu2-linux.org firmware already installed,
+ you must first put the NSLU2 into RedBoot Upgrade Mode.
+
+ - The NSLU2 should still be powered off at this point. If not,
+ shut it down again before proceeding.
+
+ - Using a paper clip, push and hold in the reset button which is
+ located on the back of the NSLU2 near the power socket.
+
+ - While holding in the reset button, press and release the power
+ button.
+
+ - Watch the Ready/Status LED, and as soon as it turns red quickly
+ release the reset button.
+
+ - You should now be in upgrade mode which is indicated by the
+ Ready/Status LED alternating between red and green.
+
+ - Use either the Linux UpSlug2 tool or the Windows SerComm Upgrade
+ tool to upload the new firmware - you can find download links at
+ http://www.nslu2-linux.org/wiki/HowTo/InstallUnslungFirmware
+
+ - During firmware flashing, the top LED - Ready/Status - flashes
+ red and green (approximately 5 minutes, but can be much longer).
+
+ - The NSLU2 will reboot after the flashing is complete.
3) Shutdown the NSLU2 (again), attach disk(s), and power it back up.