linux-ezx: improve rokre6 support

5 files changed, 336 insertions, 12 deletions

diff --git a/packages/linux/linux-ezx-2.6.21/patches/e6-eoc.patch b/packages/linux/linux-ezx-2.6.21/patches/e6-eoc.patch
new file mode 100644
index 0000000000..79c60c8ca2
--- /dev/null
+++ b/packages/linux/linux-ezx-2.6.21/patches/e6-eoc.patch
@@ -0,0 +1,82 @@
+Index: linux-2.6.21/arch/arm/mach-pxa/ezx-e6.c
+===================================================================
+--- linux-2.6.21.orig/arch/arm/mach-pxa/ezx-e6.c	2007-09-07 22:15:52.000000000 -0300
++++ linux-2.6.21/arch/arm/mach-pxa/ezx-e6.c	2007-09-09 13:29:56.000000000 -0300
+@@ -25,6 +25,7 @@
+ #include <asm/arch/mmc.h>
+ 
+ #include "generic.h"
++#include "ezx-eoc.h"
+ 
+ extern void ezx_lcd_power(int, struct fb_var_screeninfo *);
+ extern void ezx_backlight_power(int);
+@@ -227,11 +228,69 @@
+ 	.resource       = pcap_ts_resources,
+ };
+ 
++
++/* EOC */
++static const unsigned int tab_init_eoc_reg[][2] =
++{
++    {POWER_IC_REG_EOC_INT_MASK,        0x00000FEF},
++    {POWER_IC_REG_EOC_POWER_CONTROL_0, 0x00000C00},
++    {POWER_IC_REG_EOC_POWER_CONTROL_1, 0x0000000C},
++    {POWER_IC_REG_EOC_CONN_CONTROL,    0x00021044},
++};
++
++static void dump_eoc_registers(void)
++{
++	int i, val = 0;
++
++	printk("========DUMP EOC=========\n");
++	for (i = 0; i < POWER_IC_REG_EOC_NUM; i++) {
++		eoc_reg_read(i, &val);
++		printk("eoc_registers[%d] = 0x%08X\n", i, val);
++	}
++	printk("========END DUMP=========\n");
++}
++
++/*
++ * FIXME: The same about the PCAP driver applies here.
++ * This is the initial state only.
++ * Which bits does the change to USB/UART/AUDIO mode?
++ * I think that this is causing the crash on pxa27x-udc
++ * you are setting the 'port connected' bit, and thats why
++ * you are getting interrupts early.
++ * --WM
++ */
++
++static int __init e6_eoc_init(void)
++{
++    int i;
++
++    for (i = 0; i < sizeof(tab_init_eoc_reg)/sizeof(unsigned int)/2; i++)
++    {
++		eoc_reg_write(tab_init_eoc_reg[i][0], tab_init_eoc_reg[i][1]);
++    }
++	dump_eoc_registers();
++	return 0;
++}
++
++static struct ezx_eoc_platform_data e6_eoc_platform_data = {
++	.init		= e6_eoc_init,
++};
++
++struct platform_device e6_eoc_device = {
++	.name		= "ezx-eoc",
++	.id		= -1,
++	.dev		= {
++		.platform_data = &e6_eoc_platform_data,
++	},
++};
++
+ static struct platform_device *devices[] __initdata = {
+ 	&e6_pcap_device,
+ 	&pcap_ts_device,
++	&e6_eoc_device,
+ };
+ 
++
+ static void __init e6_init(void)
+ {
+ 	set_pxa_fb_info(&e6_fb_info);
diff --git a/packages/linux/linux-ezx-2.6.21/patches/e6-mci.patch b/packages/linux/linux-ezx-2.6.21/patches/e6-mci.patch
new file mode 100644
index 0000000000..08a6f97820
--- /dev/null
+++ b/packages/linux/linux-ezx-2.6.21/patches/e6-mci.patch
@@ -0,0 +1,124 @@
+Index: linux-2.6.21/arch/arm/mach-pxa/ezx-e6.c
+===================================================================
+--- linux-2.6.21.orig/arch/arm/mach-pxa/ezx-e6.c	2007-09-07 11:51:55.000000000 -0300
++++ linux-2.6.21/arch/arm/mach-pxa/ezx-e6.c	2007-09-07 11:54:52.000000000 -0300
+@@ -13,6 +13,8 @@
+ #include <linux/init.h>
+ #include <linux/platform_device.h>
+ #include <linux/fb.h>
++#include <linux/mmc/host.h>
++#include <linux/irq.h>
+ 
+ #include <asm/mach-types.h>
+ #include <asm/mach/arch.h>
+@@ -20,12 +22,102 @@
+ #include <asm/arch/pxafb.h>
+ #include <asm/arch/ezx.h>
+ #include <asm/arch/ezx-pcap.h>
++#include <asm/arch/mmc.h>
+ 
+ #include "generic.h"
+ 
+ extern void ezx_lcd_power(int, struct fb_var_screeninfo *);
+ extern void ezx_backlight_power(int);
+ 
++#ifdef CONFIG_EZX_PCAP
++extern int ezx_pcap_mmcsd_power(int);
++extern void ezx_pcap_mmcsd_voltage(u_int32_t);
++#else
++#define ezx_pcap_mmcsd_voltage(x) {}
++#define ezx_pcap_mmcsd_power(x) {}
++#endif
++
++static struct pxamci_platform_data e6_mci_platform_data;
++
++static u_int8_t mmc_voltage[] = {
++	[MMC_VDD_160] = 5,
++	[MMC_VDD_170] = 5,
++	[MMC_VDD_180] = 6,
++	[MMC_VDD_190] = 6,
++	[MMC_VDD_200] = 7,
++	[MMC_VDD_210] = 7,
++	[MMC_VDD_220] = 8,
++	[MMC_VDD_230] = 8,
++	[MMC_VDD_240] = 9,
++	[MMC_VDD_250] = 9,
++	[MMC_VDD_260] = 10,
++	[MMC_VDD_270] = 10,
++	[MMC_VDD_280] = 11,
++	[MMC_VDD_290] = 11,
++	[MMC_VDD_300] = 12,
++	[MMC_VDD_310] = 12,
++	[MMC_VDD_320] = 13,
++	[MMC_VDD_330] = 13,
++	[MMC_VDD_340] = 14,
++	[MMC_VDD_350] = 14,
++	[MMC_VDD_360] = 15,
++};
++
++static int e6_mci_init(struct device *dev,
++                       irqreturn_t (*ezx_detect_int)(int, void *),
++                       void *data)
++{
++       int err;
++
++       /* Setup GPIO for PXA27x MMC/SD controller */
++       pxa_gpio_mode(GPIO32_MMCCLK_MD);
++       pxa_gpio_mode(GPIO112_MMCCMD_MD);
++       pxa_gpio_mode(GPIO92_MMCDAT0_MD);
++       pxa_gpio_mode(GPIO109_MMCDAT1_MD);
++       pxa_gpio_mode(GPIO110_MMCDAT2_MD);
++       pxa_gpio_mode(GPIO111_MMCDAT3_MD);
++
++       ezx_pcap_mmcsd_power(1);
++
++       e6_mci_platform_data.detect_delay = msecs_to_jiffies(250);
++
++       err = request_irq(0x49, ezx_detect_int, SA_INTERRUPT,
++                       "MMC card detect", data);
++       if (err) {
++               printk(KERN_ERR "ezx_mci_detect: MMC/SD: can't request "
++                       "MMC card detect IRQ\n");
++               return -1;
++       }
++
++       set_irq_type(0x0b, IRQT_BOTHEDGE);
++
++       return 0;
++}
++
++static void e6_mci_setpower(struct device *dev, unsigned int vdd)
++{
++	if (vdd <= MMC_VDD_360)
++		ezx_pcap_mmcsd_voltage(mmc_voltage[vdd]);
++
++	ezx_pcap_mmcsd_power(1);
++}
++
++static void e6_mci_exit(struct device *dev, void *data)
++{
++	ezx_pcap_mmcsd_power(0);
++	free_irq(0x49, data);
++}
++
++static struct pxamci_platform_data e6_mci_platform_data = {
++	.ocr_mask       = MMC_VDD_160_165|MMC_VDD_18_19|MMC_VDD_20_21
++			  |MMC_VDD_22_23|MMC_VDD_24_25|MMC_VDD_26_27
++			  |MMC_VDD_28_29|MMC_VDD_30_31|MMC_VDD_32_33
++			  |MMC_VDD_34_35|MMC_VDD_35_36,
++	.init           = e6_mci_init,
++	.setpower       = e6_mci_setpower,
++	.exit           = e6_mci_exit,
++};
++
+ static struct pxafb_mode_info mode_e6 = {
+        .pixclock = 192308,
+        .xres = 240,
+@@ -118,6 +210,7 @@
+ static void __init e6_init(void)
+ {
+ 	set_pxa_fb_info(&e6_fb_info);
++	pxa_set_mci_info(&e6_mci_platform_data);
+ 
+ 	platform_add_devices(devices, ARRAY_SIZE(devices));
+ }
diff --git a/packages/linux/linux-ezx-2.6.21/patches/e6-pcap.patch b/packages/linux/linux-ezx-2.6.21/patches/e6-pcap.patch
new file mode 100644
index 0000000000..a11adbc02e
--- /dev/null
+++ b/packages/linux/linux-ezx-2.6.21/patches/e6-pcap.patch
@@ -0,0 +1,83 @@
+Index: linux-2.6.21/arch/arm/mach-pxa/ezx-e6.c
+===================================================================
+--- linux-2.6.21.orig/arch/arm/mach-pxa/ezx-e6.c	2007-09-07 11:32:32.000000000 -0300
++++ linux-2.6.21/arch/arm/mach-pxa/ezx-e6.c	2007-09-07 11:51:55.000000000 -0300
+@@ -19,6 +19,7 @@
+ #include <asm/arch/pxa-regs.h>
+ #include <asm/arch/pxafb.h>
+ #include <asm/arch/ezx.h>
++#include <asm/arch/ezx-pcap.h>
+ 
+ #include "generic.h"
+ 
+@@ -48,7 +49,70 @@
+        .pxafb_lcd_power = &ezx_lcd_power,
+ };
+ 
++/* PCAP */
++static int __init e6_pcap_init(void)
++{
++	/*
++	 * FIXME: this is the PCAP INITIAL STATE.
++	 * most of these writes should NOT be done here
++	 * * voltage regulators, voltage enablers should be set by the
++	 *   driver which uses the connected hardware. Otherwise you
++	 *   drain power unnecessarily.
++	 * * interrupt related registers should be set by the irq functions
++	 *   only. I think that the INT_SEL register selects on which irq
++	 *   pin the (ap/bp) the irq goes. This should go on ezx-pcap.c, but
++	 *   only if it actually makes any difference.
++	 * * Only power state automatic changes should be done here.
++	 *   (*LOWPWR, *STBY, LOWPWR*)
++	 * * I removed some writes which i consider extremelly wrong. And
++	 *   which i think will not break anything (they were overwritten
++	 *   later anyway).
++	 *
++	 *   --WM
++	 */
++	ezx_pcap_write(PCAP_REG_INT_SEL, 0x0); /* wrong */
++	ezx_pcap_write(PCAP_REG_SWCTRL, 0x2ee6); /* partially wrong */
++	ezx_pcap_write(PCAP_REG_VREG1, 0x15778e3); /* wrong */
++	ezx_pcap_write(PCAP_REG_VREG2, 0x810234); /* partially wrong */
++	ezx_pcap_write(PCAP_REG_AUXVREG, 0x1024bec); /* wrong */
++	ezx_pcap_write(PCAP_REG_PWR, 0x94108); /* partially wrong */
++	ezx_pcap_write(PCAP_REG_AUXVREG_MASK, 0x214d48); /* wrong */
++	ezx_pcap_write(PCAP_REG_BUSCTRL, 0x2a0); /* wrong */
++	ezx_pcap_write(PCAP_REG_LOWPWR, 0x1d9610c);
++	ezx_pcap_write(PCAP_REG_PERIPH, 0x0); /* wrong */
++	ezx_pcap_write(PCAP_REG_GP, 0x107); /* probably unnecessary */
++
++	return 0;
++}
++
++static struct pcap_platform_data e6_pcap_platform_data = {
++	.port		= 1,
++	.cs		= GPIO_SPI_CE,
++	.flags		= PCAP_CS_AH | PCAP_MCI_SD,
++	.clk		= 1,
++	.init		= e6_pcap_init,
++};
++
++static struct resource e6_pcap_resources[] = {
++	[0] = {
++		.start		= IRQ_GPIO1,
++		.end		= IRQ_GPIO1,
++		.flags		= IORESOURCE_IRQ,
++	},
++};
++
++struct platform_device e6_pcap_device = {
++	.name		= "ezx-pcap",
++	.id		= -1,
++	.num_resources	= ARRAY_SIZE(e6_pcap_resources),
++	.resource	= e6_pcap_resources,
++	.dev		= {
++		.platform_data = &e6_pcap_platform_data,
++	},
++};
++
+ static struct platform_device *devices[] __initdata = {
++	&e6_pcap_device,
+ };
+ 
+ static void __init e6_init(void)
diff --git a/packages/linux/linux-ezx-2.6.21/patches/e6-ts.patch b/packages/linux/linux-ezx-2.6.21/patches/e6-ts.patch
new file mode 100644
index 0000000000..6472f77886
--- /dev/null
+++ b/packages/linux/linux-ezx-2.6.21/patches/e6-ts.patch
@@ -0,0 +1,38 @@
+Index: linux-2.6.21/arch/arm/mach-pxa/ezx-e6.c
+===================================================================
+--- linux-2.6.21.orig/arch/arm/mach-pxa/ezx-e6.c	2007-09-07 11:54:52.000000000 -0300
++++ linux-2.6.21/arch/arm/mach-pxa/ezx-e6.c	2007-09-07 11:55:10.000000000 -0300
+@@ -203,8 +203,33 @@
+ 	},
+ };
+ 
++/* PCAP_TS */
++struct resource pcap_ts_resources[] = {
++	[0] = {
++		.start          = EZX_IRQ_ADCDONE,
++		.end            = EZX_IRQ_ADCDONE,
++		.flags          = IORESOURCE_IRQ,
++	},
++	[1] = {
++		.start          = EZX_IRQ_TS,
++		.end            = EZX_IRQ_TS,
++		.flags          = IORESOURCE_IRQ,
++	}
++};
++
++struct platform_device pcap_ts_device = {
++	.name           = "pcap-ts",
++	.id             = -1,
++	.dev		= {
++		.parent = &e6_pcap_device.dev,
++	},
++	.num_resources  = ARRAY_SIZE(pcap_ts_resources),
++	.resource       = pcap_ts_resources,
++};
++
+ static struct platform_device *devices[] __initdata = {
+ 	&e6_pcap_device,
++	&pcap_ts_device,
+ };
+ 
+ static void __init e6_init(void)
diff --git a/packages/linux/linux-ezx-2.6.21/patches/ezx-eoc.patch b/packages/linux/linux-ezx-2.6.21/patches/ezx-eoc.patch
index f21894e904..77c79fd107 100644
--- a/packages/linux/linux-ezx-2.6.21/patches/ezx-eoc.patch
+++ b/packages/linux/linux-ezx-2.6.21/patches/ezx-eoc.patch
@@ -1,8 +1,8 @@
 Index: linux-2.6.21/arch/arm/mach-pxa/ezx-eoc.c
 ===================================================================
 --- /dev/null	1970-01-01 00:00:00.000000000 +0000
-+++ linux-2.6.21/arch/arm/mach-pxa/ezx-eoc.c	2007-09-09 13:33:19.000000000 -0300
-@@ -0,0 +1,270 @@
++++ linux-2.6.21/arch/arm/mach-pxa/ezx-eoc.c	2007-09-11 20:14:33.000000000 -0300
+@@ -0,0 +1,267 @@
 +/*
 + *  EZX EOC Driver for Motorola EZX phones
 + *
@@ -182,11 +182,8 @@ Index: linux-2.6.21/arch/arm/mach-pxa/ezx-eoc.c
 +
 +	eoc_i2c_client = new_client;
 +
-+	if (pdata && pdata->init) {
++	if (pdata && pdata->init)
 +		pdata->init();
-+		}
-+	else
-+		return -EINVAL;
 +
 +	eoc_switch_to_default();
 +
@@ -276,7 +273,7 @@ Index: linux-2.6.21/arch/arm/mach-pxa/ezx-eoc.c
 Index: linux-2.6.21/arch/arm/mach-pxa/ezx-eoc.h
 ===================================================================
 --- /dev/null	1970-01-01 00:00:00.000000000 +0000
-+++ linux-2.6.21/arch/arm/mach-pxa/ezx-eoc.h	2007-09-07 22:15:52.000000000 -0300
++++ linux-2.6.21/arch/arm/mach-pxa/ezx-eoc.h	2007-09-09 21:46:27.000000000 -0300
 @@ -0,0 +1,33 @@
 +/*
 + *  linux/arch/arm/mach-pxa/ezx-eoc.h
@@ -313,15 +310,15 @@ Index: linux-2.6.21/arch/arm/mach-pxa/ezx-eoc.h
 +#endif /* __EZX_EOC_H__ */
 Index: linux-2.6.21/arch/arm/mach-pxa/Kconfig
 ===================================================================
---- linux-2.6.21.orig/arch/arm/mach-pxa/Kconfig	2007-09-07 22:15:52.000000000 -0300
-+++ linux-2.6.21/arch/arm/mach-pxa/Kconfig	2007-09-07 22:15:52.000000000 -0300
+--- linux-2.6.21.orig/arch/arm/mach-pxa/Kconfig	2007-09-09 21:46:27.000000000 -0300
++++ linux-2.6.21/arch/arm/mach-pxa/Kconfig	2007-09-09 21:46:27.000000000 -0300
 @@ -108,6 +108,12 @@
  config EZX_PCAP
  	bool "PCAP Support"
  
 +config EZX_EOC
 +	tristate "EOC i2c driver of Motorola EZX phones"
-+	depends on I2C && EXPERIMENTAL && PXA_EZX_A1200
++	depends on I2C && EXPERIMENTAL
 +	help
 +	  EOC i2c driver of Motorola EZX phones
 +
@@ -330,8 +327,8 @@ Index: linux-2.6.21/arch/arm/mach-pxa/Kconfig
  	depends on EZX_PCAP
 Index: linux-2.6.21/arch/arm/mach-pxa/Makefile
 ===================================================================
---- linux-2.6.21.orig/arch/arm/mach-pxa/Makefile	2007-09-07 22:15:52.000000000 -0300
-+++ linux-2.6.21/arch/arm/mach-pxa/Makefile	2007-09-07 22:15:52.000000000 -0300
+--- linux-2.6.21.orig/arch/arm/mach-pxa/Makefile	2007-09-09 21:46:27.000000000 -0300
++++ linux-2.6.21/arch/arm/mach-pxa/Makefile	2007-09-09 21:46:27.000000000 -0300
 @@ -27,6 +27,7 @@
  obj-$(CONFIG_EZX_BP)		+= ezx-bp.o
  obj-$(CONFIG_EZX_PCAP)		+= ezx-pcap.o