slugos: Subsumed slugos-lag.conf into slugosle.conf, slugos-bag.conf into slugosbe.conf, and dropped slugos-{b,l}ag.conf. Deprecated openslug.conf in favour of slugosbe.conf. Deprecated debianslug.conf in favour of slugosle.conf. Eventually this all might be done with multimachine.

1 files changed, 1 insertions, 117 deletions

diff --git a/conf/distro/openslug.conf b/conf/distro/openslug.conf
index 40cf6354f3..943ce1a985 100644
--- a/conf/distro/openslug.conf
+++ b/conf/distro/openslug.conf
@@ -2,122 +2,6 @@
 #@NAME: OpenSlug
 #@DESCRIPTION: OpenSlug Linux Distribution for the NSLU2
 
-#----------------------------------------------------------------------------------
-# STANDARD OpenSlug DEFINITIONS
-#----------------------------------------------------------------------------------
-DISTRO_NAME = "OpenSlug"
-# DISTRO_VERSION = "${SLUGOS_VERSION}${DISTRO_REVISION}-${DISTRO_TYPE}"
-# DISTRO_FEED = "unstable"
-DISTRO_TYPE = "beta"
 SLUGOS_DISTRO = "openslug"
 
-#----------------------------------------------------------------------------------
-# FIRMWARE CONFIGURATION
-#----------------------------------------------------------------------------------
-# EXTRA PACKAGES
-# --------------
-# Filesystem support modules are listed in here for easy removal,
-# as is the lrzsz serial package and other kernel modules which are
-# not absolutely required for boot.
-# NOTE: only jffs2 support is an absolute requirement of boot, even
-# the ext2/ext3 support is optional!
-OPENSLUG_EXT2_PROGS =  "e2fsprogs-mke2fs e2fsprogs-fsck e2fsprogs-e2fsck e2fsprogs-badblocks"
-
-# The standard firmware contents and additional packages built as requirements
-# of the firmware are defined here in OPENSLUG_STANDARD_RDEPENDS and
-# OPENSLUG_STANDARD_DEPENDS respectively.
-OPENSLUG_STANDARD_RDEPENDS = ""
-
-# Support for a variety of file systems is built in to the openslug
-# image, programs to format disks with these file systems may be
-# added or removed.  By default ext2 and ext3 support
-# is included by the following lines.
-# 
-# These lines add support for formatting ext2 and ext3 file systems
-# on a hard disk attached to the NSLU2.  ext3 is the standard Linux
-# file system.
-OPENSLUG_STANDARD_RDEPENDS += "${OPENSLUG_EXT2_PROGS}"
-
-# These lines add support for an X/Y/ZModem package called lrzsz
-# (this is of use for people with modified NSLU2 hardware which
-# supports a serial port.)
-OPENSLUG_STANDARD_RDEPENDS += "lrzsz"
-
-# Filesystem selection.  Adding entries here adds the module to the
-# image.  The module must be built as part of nslu2-kernel (i.e. it
-# must be specified as a module in the defconfig file).  The NLS
-# support charset modules must be given explicitly and must match
-# the codepage/iocharset and NLS handling for the file systems which
-# require them.  The installed lanugage set is minimal but sufficient
-# for any file system (since it uses utf8).  See
-# http://www.nslu2-linux.orgwiki/HowTo/MountFATFileSystems
-# for more information on the language behaviour of the DOS file
-# systems.
-#
-# KERNEL LEVEL FILE SYSTEM SUPPORT
-# --------------------------------
-# NOTE: removing kernel-module-nfs from this list will prevent NFS
-# boot (however you can do a simple flash file system boot - no
-# attached disk - and install the nfs modules from ssh.)
-OPENSLUG_STANDARD_RDEPENDS += "\
-kernel-module-ext2 \
-kernel-module-jbd \
-kernel-module-ext3 \
-kernel-module-vfat \
-kernel-module-ntfs \
-kernel-module-isofs \
-kernel-module-udf \
-kernel-module-nls-cp437 \
-kernel-module-nls-utf8 \
-"
-
-# Add daemon required for HW RNG support
-OPENSLUG_STANDARD_RDEPENDS += "\
-rng-tools \
-"
-
-# Add modules required for usb support
-OPENSLUG_STANDARD_RDEPENDS += "\
-kernel-module-ohci-hcd \
-kernel-module-uhci-hcd \
-"
-
-# Add modules required for IDE support
-OPENSLUG_STANDARD_RDEPENDS += "\
-kernel-module-libata \
-kernel-module-pata-artop \
-"
-
-# Add modules required for Network support
-OPENSLUG_STANDARD_RDEPENDS += "\
-kernel-module-via-velocity \
-"
-
-# This documents other file systems which are built but not installed
-# by default in the flash image.
-#
-# kernel-module-msdos - mounts a FAT file system without long file names
-#                       (use kernel-module-vfat, it shows the long names
-#                       if present.)
-
-# The 'standard' values are the defaults for the 'extra' packages added
-# to the firmware image.  None of these things are requirements to have
-# a bootable, useable, system however they *are* expected to be present
-# in OpenSlug - see nslu2-bag for a more minimal configuration and some
-# more instructions about how to make a non-openslug image.
-OPENSLUG_EXTRA_RDEPENDS ?= ""
-SLUGOS_EXTRA_RDEPENDS = "${OPENSLUG_STANDARD_RDEPENDS} ${OPENSLUG_EXTRA_RDEPENDS}"
-
-#----------------------------------------------------------------------------------
-# PACKAGE VERSION CONTROL
-#----------------------------------------------------------------------------------
-PREFERRED_VERSION_nslu2-linksys-firmware ?= "2.3r63"
-
-#----------------------------------------------------------------------------------
-# BASE VERSION SELECTION
-#----------------------------------------------------------------------------------
-# b - big-endian
-# a - ARM instruction set
-# g - glibc
-#
-require conf/distro/slugos-bag.conf
+require conf/distro/slugosbe.conf