summaryrefslogtreecommitdiff
path: root/recipes-kernel
AgeCommit message (Expand)AuthorFiles
2019-11-11Bump kernel revision for Quectel patch5.1.8John Klug1
2019-11-11Adding tmp102 module to the available modulesJohn Klug1
2019-11-11new rs9113rf commands with maximum flexibilityJohn Klug4
2019-11-11Update QMI WWAN patch for QuectelJeff Hatch1
2019-11-11rs9113-btclonly depends on rs9113-noarchJohn Klug1
2019-11-11Add linux-4.9-quectel_qmi_wwan_support.patch to linux-at91_4.9.87.bb recipeJeff Hatch1
2019-11-11Additional updates to qmi for Quectel radio supportJeff Hatch1
2019-07-03btclonly package for rs9113, and mths compatible "machine" for kernelJohn Klug2
2019-07-03150mS does not work with MTHS, so try 300mS timeout on PMECCJohn Klug2
2019-07-03Add the xt physdev match module for MTHSJohn Klug1
2019-07-03Remove vbus-gpio which breaks the USB interface.John Klug2
2019-07-03Set output low on the GNSS-RESET lineJohn Klug1
2019-07-03Add support to option driver for Quectel EG955.0.0Jeff Hatch2
2019-07-03GNSS reset fix to suppress GPS serial port to protect XR12V1414 from bad PID/VIDJohn Klug2
2019-07-03Allow for antenna gain in wf commandJohn Klug3
2019-07-03Bump the version of rs9113rfJohn Klug1
2019-07-03Add device type to signal stop.John Klug1
2019-07-03Bump revision of rs9113rf to fix antenna portJohn Klug1
2019-07-03Wrong antenna portJohn Klug1
2019-07-03Bump the revision of the kernel for new device treeJohn Klug1
2019-07-03Remove unused mmc pins, and put in PD14-PD20 in mtrv1John Klug1
2019-07-03rs9113 1.6.1 requires a base_interface name for the transmit commandJohn Klug3
2019-07-03Use output-high for MTCDT PD14-PD19 resetsJohn Klug1
2019-07-03Autoload i2c-dev for LoRa usersJohn Klug1
2019-07-03Use Redpine bridge patchJohn Klug2
2019-07-03Use Redpine bridge patchJohn Klug2
2019-07-03Remove unused mmc1-boardJohn Klug1
2019-07-03Syntax error in device treeJohn Klug1
2019-07-03Missing semicolon in device tree.John Klug1
2019-07-03Typo in name of patch for led brightnessJohn Klug1
2019-07-03Fix LED status on upgrade.John Klug2
2019-07-03Correct the SDIO active pin to PA1, and set deglitchJohn Klug1
2019-07-03Blink LEDs when kernel loads, not when modules loadJohn Klug2
2019-07-03Bump the version of rs9113 for new firmware and WEP fix.John Klug2
2019-07-03Bump kernel revision for CGROUPSJohn Klug1
2019-07-03Remove BLK_CGROUP and add PROC_EVENTS, and take the consequences from make me...John Klug1
2019-07-03Make defconfig compatible with make menuconfig again.John Klug1
2019-07-03rs9113-autostart depends on rs9113-noarchJohn Klug1
2019-07-03rs9113 startup moved to package rs9113-autostartJohn Klug3
2019-07-03rs9113 package arch updates (all, arm926ejste)John Klug1
2019-07-03Bump the version of rs9113 package to correspond to driver patchJohn Klug2
2019-07-03All LTE MTR types can user B18 as the PPS signalJohn Klug1
2019-07-03Change pps to pps-0 in device tree to allow for multiple entries.John Klug1
2019-07-03Add rising edge IRQ to Murata - this is required for proper interruptMike Nicholson1
2019-07-03Use timing from previous software iterations.Mike Nicholson1
2019-07-03Enable/disable murata in wl12xx SDIO driver; deglitch, remove pull-downMike Nicholson3
2019-07-03Security enhancement (ASLR) : Disable CONFIG_COMPAT_BRK so that randomize_va_...Jeff Hatch1
2019-07-03Make it clear why there are two PPS pins definedJohn Klug1
2019-07-03Add PPS for MTRV1-0.0 and MTRV1-0.1John Klug1
2019-07-03Add the DT Overlay patch to kernel for MTRV1John Klug1
generated by cgit v1.2.3 (git 2.25.1) at 2024-05-20 09:19:26 +0000