| Age | Commit message (Expand) | Author | Files |
|---|
| 2019-07-03 | Add support to option driver for Quectel EG955.0.0 | Jeff Hatch | 2 |
| 2019-07-03 | GNSS reset fix to suppress GPS serial port to protect XR12V1414 from bad PID/VID | John Klug | 2 |
| 2019-07-03 | Allow for antenna gain in wf command | John Klug | 3 |
| 2019-07-03 | Bump the version of rs9113rf | John Klug | 1 |
| 2019-07-03 | Add device type to signal stop. | John Klug | 1 |
| 2019-07-03 | Bump revision of rs9113rf to fix antenna port | John Klug | 1 |
| 2019-07-03 | Wrong antenna port | John Klug | 1 |
| 2019-07-03 | Bump the revision of the kernel for new device tree | John Klug | 1 |
| 2019-07-03 | Remove unused mmc pins, and put in PD14-PD20 in mtrv1 | John Klug | 1 |
| 2019-07-03 | rs9113 1.6.1 requires a base_interface name for the transmit command | John Klug | 3 |
| 2019-07-03 | Use output-high for MTCDT PD14-PD19 resets | John Klug | 1 |
| 2019-07-03 | Autoload i2c-dev for LoRa users | John Klug | 1 |
| 2019-07-03 | Use Redpine bridge patch | John Klug | 2 |
| 2019-07-03 | Use Redpine bridge patch | John Klug | 2 |
| 2019-07-03 | Remove unused mmc1-board | John Klug | 1 |
| 2019-07-03 | Syntax error in device tree | John Klug | 1 |
| 2019-07-03 | Missing semicolon in device tree. | John Klug | 1 |
| 2019-07-03 | Typo in name of patch for led brightness | John Klug | 1 |
| 2019-07-03 | Fix LED status on upgrade. | John Klug | 2 |
| 2019-07-03 | Correct the SDIO active pin to PA1, and set deglitch | John Klug | 1 |
| 2019-07-03 | Blink LEDs when kernel loads, not when modules load | John Klug | 2 |
| 2019-07-03 | Bump the version of rs9113 for new firmware and WEP fix. | John Klug | 2 |
| 2019-07-03 | Bump kernel revision for CGROUPS | John Klug | 1 |
| 2019-07-03 | Remove BLK_CGROUP and add PROC_EVENTS, and take the consequences from make me... | John Klug | 1 |
| 2019-07-03 | Make defconfig compatible with make menuconfig again. | John Klug | 1 |
| 2019-07-03 | rs9113-autostart depends on rs9113-noarch | John Klug | 1 |
| 2019-07-03 | rs9113 startup moved to package rs9113-autostart | John Klug | 3 |
| 2019-07-03 | rs9113 package arch updates (all, arm926ejste) | John Klug | 1 |
| 2019-07-03 | Bump the version of rs9113 package to correspond to driver patch | John Klug | 2 |
| 2019-07-03 | All LTE MTR types can user B18 as the PPS signal | John Klug | 1 |
| 2019-07-03 | Change pps to pps-0 in device tree to allow for multiple entries. | John Klug | 1 |
| 2019-07-03 | Add rising edge IRQ to Murata - this is required for proper interrupt | Mike Nicholson | 1 |
| 2019-07-03 | Use timing from previous software iterations. | Mike Nicholson | 1 |
| 2019-07-03 | Enable/disable murata in wl12xx SDIO driver; deglitch, remove pull-down | Mike Nicholson | 3 |
| 2019-07-03 | Security enhancement (ASLR) : Disable CONFIG_COMPAT_BRK so that randomize_va_... | Jeff Hatch | 1 |
| 2019-07-03 | Make it clear why there are two PPS pins defined | John Klug | 1 |
| 2019-07-03 | Add PPS for MTRV1-0.0 and MTRV1-0.1 | John Klug | 1 |
| 2019-07-03 | Add the DT Overlay patch to kernel for MTRV1 | John Klug | 1 |
| 2019-07-03 | Allow CONFIG to be set externally. | John Klug | 1 |
| 2019-07-03 | Add DMA to dbgu (not on uart0) | Mike Nicholson | 1 |
| 2019-07-03 | Remove bt_transmit from the rs9113-utils file list, since it is not there any... | John Klug | 1 |
| 2019-07-03 | Remove wpa_supplicant init script from rs9113-noarch, and simplify recipe. | John Klug | 3 |
| 2019-07-03 | Add a couple jiffies of slack in the PMECCERRLOC | Mike Nicholson | 2 |
| 2019-07-03 | DMA for dbgu on MTCDT, and MTCAP (MTCAP requires testing) | Mike Nicholson | 2 |
| 2019-07-03 | Split off seldom used rs9113 driver files | John Klug | 3 |
| 2019-07-03 | New rs9113 driver for Linux versions up to 4.14 | John Klug | 2 |
| 2019-07-03 | Enable DMA on dbgu serial (fixes overrun issue) | Mike Nicholson | 1 |
| 2019-07-03 | Add DMA to uart0, delete m25p80 | Mike Nicholson | 1 |
| 2019-07-03 | Add mts-io/John's radio reset, remove m25p80, remove 16-bit nand, streamline ... | Mike Nicholson | 1 |
| 2019-07-03 | Use DMA for Venus on gps0/ttyS1, get Venus working | Mike Nicholson | 1 |
