meta-multitech-atmel.git - MultiTech BSP Layer for Atmel processors

Age	Commit message (Expand)	Author	Files
2019-12-20	Fix typo in remount read-only code	John Klug	1
2019-12-11	Add a package to remove rs9113 when not needed	John Klug	1
2019-12-11	Add new package rs9113-rm to remove rs9113 packages from devices with no rs91...	John Klug	3
2019-10-03	Bump kernel revision for Quectel patch	John Klug	1
2019-10-03	Adding tmp102 module to the available modules	John Klug	1
2019-10-02	new rs9113rf commands with maximum flexibility	John Klug	4
2019-09-26	Update QMI WWAN patch for Quectel	Jeff Hatch	1
2019-08-15	rs9113-btclonly depends on rs9113-noarch	John Klug	1
2019-07-29	Add linux-4.9-quectel_qmi_wwan_support.patch to linux-at91_4.9.87.bb recipe	Jeff Hatch	1
2019-07-29	Merge branch 'master' of gitlab.multitech.net:mirrors/meta-multitech	Jeff Hatch	2
2019-07-29	Additional updates to qmi for Quectel radio support	Jeff Hatch	1
2019-06-25	btclonly package for rs9113, and mths compatible "machine" for kernel	John Klug	2
2019-06-17	150mS does not work with MTHS, so try 300mS timeout on PMECC	John Klug	2
2019-05-31	Add the xt physdev match module for MTHS	John Klug	1
2019-05-28	Remove vbus-gpio which breaks the USB interface.	John Klug	2
2019-05-24	Set output low on the GNSS-RESET line	John Klug	1
2019-05-23	Add support to option driver for Quectel EG95	Jeff Hatch	2
2019-05-23	GNSS reset fix to suppress GPS serial port to protect XR12V1414 from bad PID/VID	John Klug	2
2019-05-16	Allow for antenna gain in wf command	John Klug	3
2019-05-09	Bump the version of rs9113rf	John Klug	1
2019-05-09	Add device type to signal stop.	John Klug	1
2019-05-08	Bump revision of rs9113rf to fix antenna port	John Klug	1
2019-05-08	Wrong antenna port	John Klug	1
2019-05-07	Bump the revision of the kernel for new device tree	John Klug	1
2019-05-07	Remove unused mmc pins, and put in PD14-PD20 in mtrv1	John Klug	1
2019-05-07	rs9113 1.6.1 requires a base_interface name for the transmit command	John Klug	3
2019-04-24	Use output-high for MTCDT PD14-PD19 resets	John Klug	1
2019-04-24	Autoload i2c-dev for LoRa users	John Klug	1
2019-04-17	Use Redpine bridge patch	John Klug	2
2019-04-17	Use Redpine bridge patch	John Klug	2
2019-04-15	Remove unused mmc1-board	John Klug	1
2019-04-05	Syntax error in device tree	John Klug	1
2019-04-05	Missing semicolon in device tree.	John Klug	1
2019-04-05	Typo in name of patch for led brightness	John Klug	1
2019-04-04	Fix LED status on upgrade.	John Klug	2
2019-04-04	Correct the SDIO active pin to PA1, and set deglitch	John Klug	1
2019-03-27	Blink LEDs when kernel loads, not when modules load	John Klug	2
2019-03-25	Bump the version of rs9113 for new firmware and WEP fix.	John Klug	2
2019-03-22	Bump kernel revision for CGROUPS	John Klug	1
2019-03-21	Remove BLK_CGROUP and add PROC_EVENTS, and take the consequences from make me...	John Klug	1
2019-03-21	Make defconfig compatible with make menuconfig again.	John Klug	1
2019-03-19	rs9113-autostart depends on rs9113-noarch	John Klug	1
2019-03-19	rs9113 startup moved to package rs9113-autostart	John Klug	3
2019-03-18	rs9113 package arch updates (all, arm926ejste)	John Klug	1
2019-03-08	Bump the version of rs9113 package to correspond to driver patch	John Klug	2
2019-03-04	All LTE MTR types can user B18 as the PPS signal	John Klug	1
2019-03-04	Change pps to pps-0 in device tree to allow for multiple entries.	John Klug	1
2019-03-01	Add rising edge IRQ to Murata - this is required for proper interrupt	Mike Nicholson	1
2019-03-01	Use timing from previous software iterations.	Mike Nicholson	1
2019-02-27	Enable/disable murata in wl12xx SDIO driver; deglitch, remove pull-down	Mike Nicholson	3