summaryrefslogtreecommitdiff
AgeCommit message (Expand)AuthorFiles
2022-01-24WM_LINK_MON (LS_LED) should be an input by defaultmPower-5.3.75.3.32John Klug1
2022-01-24Change pioA7 from SPI0_NPCS1 to a GPIO inputJohn Klug2
2022-01-24Remove SAM9X5EK SPI flash from U-Boot to prevent GPIO conflictsJohn Klug2
2022-01-18Increase counts to 10 for rs9113 resetJohn Klug1
2022-01-18Do not remove module in run state 6 (Reboot), and try reset up to 10 timesJohn Klug2
2022-01-13meta-rs9113: Fix arithmetic when "set -e" is in effect (variables should not ...John Klug2
2022-01-04Hold rs9113 in reset until after USB Hub is readyJohn Klug2
2021-12-29Remove branch referenceJohn Klug1
2021-12-15Set EHCI (High Speed USB) by default for MTCDTJohn Klug1
2021-12-14Disable EHCI (High Speed USB) by default for MTCDTDisableEHCIJohn Klug1
2021-12-09Do not create extra file in /var/config for rs9113 reset. Use dmesgJohn Klug1
2021-12-09Improve logging in /etc/init.d/rs9113John Klug1
2021-12-09Add logging to evaluate rs9113 initializationJohn Klug1
2021-12-08Remove possible extra reset of rs9113John Klug1
2021-12-08User /etc/init.d/rs9113 reset in /etc/init.d/rs9113-resetJohn Klug2
2021-12-08Add rs9113-reset package for mPower to reset rs9113John Klug3
2021-12-06cd-gpio is on pioA 1 (or gpio0 pin 1)John Klug1
2021-11-30Enable XMIT and RCV in all cases when setting RS485 with Atmel serialJohn Klug1
2021-11-29Disable CRTSCTS when setting RS485 half duplex to match Vizzini driverJohn Klug2
2021-11-23Make sure mts-io is done loading, make sure loops break outJohn Klug1
2021-11-23Remove i2c debug to prevent new I/O expander debugJohn Klug1
2021-11-23New rs9113-from-src for building rs9113John Klug1
2021-11-22Wait for USB, not the interrupt pin which is too earlyJohn Klug1
2021-11-22Add a reset loop in case rs9113 does not appear on USB HubJohn Klug2
2021-11-22Fix pincontrol for io controllers, rs9113, usbhub resetsJohn Klug4
2021-11-15Remove support for IRQ because our I/O expander does not have thisJohn Klug1
2021-11-15Cannot use same stanza names at at91sam9x5cm.dtsi or partition order is incor...John Klug1
2021-11-15Device tree updates for MTCDT-0.2 and OverlayJohn Klug4
2021-11-15set PREFERRED_VERSION_rs9113 to 1.6.5Serhii Voloshynov4
2021-11-15Remove patch from recipe that is in meta-rs9113John Klug1
2021-11-15output-high and output-low are ignored by pinctrl_at91 driverJohn Klug1
2021-11-15Resets for new GPIO controllersJohn Klug1
2021-11-15Add patch for multidrop serial to match Vizzini driverJohn Klug1
2021-11-15Turn off debug in the RS9113 driver due to too many warningsJohn Klug3
2021-11-15Add dummy regulator to make gpio expander driver happyJohn Klug1
2021-11-15Call the new PCA9557 parts gpio4 and gpio5John Klug1
2021-11-15Print a message to the log when setting multidropJohn Klug1
2021-11-15r15 kernel was not yet released, so use r15John Klug1
2021-11-15Reserve 5 bit serial for multidrop in Atmel Serial driverJohn Klug2
2021-11-15Add new GPIO expanderJohn Klug1
2021-11-15Add PCA953X driver to kernel for MTCDT-0.2John Klug1
2021-09-28Have the Atmel serial driver pick the dma channelmPower-5.3.6John Klug1
2021-09-23ttyS4, external serial port, must be by default disabledJohn Klug1
2021-09-23Fix DMA for external serial port on MTRV1-0.4John Klug2
2021-09-20Add mtrv1 ttl scriptJohn Klug2
2021-09-16Random MAC for EEPROM not written to yetJohn Klug2
2021-09-10Add DMA to GNSS and External SerialJohn Klug1
2021-09-09The 5.3.x branch is for mLinux >5.3.0 and <6.0.0John Klug1
2021-09-03Fix device tree for MTRV1-0.4 and bump kernel versionJohn Klug2
2021-09-03Move to new Red compatible rs9113 driverJohn Klug2
generated by cgit v1.2.3 (git 2.25.1) at 2024-12-11 21:11:45 +0000