summaryrefslogtreecommitdiff
path: root/recipes-kernel/linux/linux-3.12.70/mtrv1/linux-3.12-mtrv1-device-tree.patch
diff options
context:
space:
mode:
Diffstat (limited to 'recipes-kernel/linux/linux-3.12.70/mtrv1/linux-3.12-mtrv1-device-tree.patch')
-rw-r--r--recipes-kernel/linux/linux-3.12.70/mtrv1/linux-3.12-mtrv1-device-tree.patch345
1 files changed, 345 insertions, 0 deletions
diff --git a/recipes-kernel/linux/linux-3.12.70/mtrv1/linux-3.12-mtrv1-device-tree.patch b/recipes-kernel/linux/linux-3.12.70/mtrv1/linux-3.12-mtrv1-device-tree.patch
new file mode 100644
index 0000000..52754ae
--- /dev/null
+++ b/recipes-kernel/linux/linux-3.12.70/mtrv1/linux-3.12-mtrv1-device-tree.patch
@@ -0,0 +1,345 @@
+diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
+index 802720e..4767358 100644
+--- a/arch/arm/boot/dts/Makefile
++++ b/arch/arm/boot/dts/Makefile
+@@ -35,6 +35,7 @@ dtb-$(CONFIG_ARCH_AT91) += at91sam9g25ek.dtb
+ dtb-$(CONFIG_ARCH_AT91) += at91sam9g35ek.dtb
+ dtb-$(CONFIG_ARCH_AT91) += at91sam9x25ek.dtb
+ dtb-$(CONFIG_ARCH_AT91) += at91sam9x35ek.dtb
++dtb-$(CONFIG_ARCH_AT91) += mtrv1.dtb
+ # sama5d3
+ dtb-$(CONFIG_ARCH_AT91) += sama5d31ek.dtb
+ dtb-$(CONFIG_ARCH_AT91) += sama5d33ek.dtb
+diff --git a/arch/arm/boot/dts/mtrv1.dts b/linux-3.12.27.mtr/arch/arm/boot/dts/mtrv1.dts
+new file mode 100644
+index 0000000..edbbe37
+--- /dev/null
++++ b/arch/arm/boot/dts/mtrv1.dts
+@@ -0,0 +1,255 @@
++/*
++ * DTS file for Multi-Tech Systems MTRv1 Hardware
++ *
++ * Copyright (C) 2016 by Multi-Tech Systems,
++ *
++ * Licensed under GPLv2 or later.
++ */
++
++/dts-v1/;
++#include "at91sam9g25.dtsi"
++
++/ {
++ model = "Multi-Tech Systems MTR";
++ compatible = "atmel,at91sam9g25ek", "atmel,at91sam9x5ek", "atmel,at91sam9x5", "atmel,at91sam9";
++
++ chosen {
++ bootargs = "mem=128M console=ttyS0,115200 root=/dev/mtdblock8 ro rootfstype=jffs2";
++ };
++
++ memory {
++ reg = <0x20000000 0x8000000>;
++ };
++
++ clocks {
++ #address-cells = <1>;
++ #size-cells = <1>;
++ ranges;
++
++ main_clock: clock@0 {
++ compatible = "atmel,osc", "fixed-clock";
++ clock-frequency = <12000000>;
++ };
++ };
++
++ ahb {
++ apb {
++ macb0: ethernet@f802c000 {
++ compatible = "cdns,at32ap7000-macb", "cdns,macb";
++ reg = <0xf802c000 0x4000>;
++ interrupts = <24 IRQ_TYPE_LEVEL_HIGH 3>;
++ pinctrl-names = "default";
++ pinctrl-0 = <&pinctrl_macb0_rmii>;
++ phy-mode = "rmii";
++ status = "okay";
++ };
++
++ /* WiFi (wl12xx) */
++ mmc0: mmc@f0008000 {
++ pinctrl-names = "default";
++ pinctrl-0 = <
++ &pinctrl_board_mmc0
++ &pinctrl_mmc0_slot0_clk_cmd_dat0
++ &pinctrl_mmc0_slot0_dat1_3>;
++ status = "okay";
++ slot@0 {
++ reg = <0>;
++ bus-width = <4>;
++ /*cd-gpios = <&pioD 15 GPIO_ACTIVE_HIGH>;*/
++ };
++ };
++
++ pinctrl@fffff400 {
++ mmc0 {
++ pinctrl_board_mmc0: mmc0-board {
++ atmel,pins =
++ <AT91_PIOD 15 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>; /* PD15 gpio CD pin pull up and deglitch */
++ };
++ };
++
++ nand {
++ pinctrl_nand: nand-0 {
++ atmel,pins =
++ <AT91_PIOD 0 AT91_PERIPH_A AT91_PINCTRL_PULL_UP /* PD0 periph A Read Enable */
++ AT91_PIOD 1 AT91_PERIPH_A AT91_PINCTRL_PULL_UP /* PD1 periph A Write Enable */
++ AT91_PIOD 2 AT91_PERIPH_A AT91_PINCTRL_PULL_UP /* PD2 periph A Address Latch Enable */
++ AT91_PIOD 3 AT91_PERIPH_A AT91_PINCTRL_PULL_UP /* PD3 periph A Command Latch Enable */
++ AT91_PIOD 4 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP /* PD4 gpio Chip Enable pin pull_up */
++ AT91_PIOC 31 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP /* PC31 gpio RDY/BUSY pin pull_up */
++ AT91_PIOD 6 AT91_PERIPH_A AT91_PINCTRL_PULL_UP /* PD6 periph A Data bit 0 */
++ AT91_PIOD 7 AT91_PERIPH_A AT91_PINCTRL_PULL_UP /* PD7 periph A Data bit 1 */
++ AT91_PIOD 8 AT91_PERIPH_A AT91_PINCTRL_PULL_UP /* PD8 periph A Data bit 2 */
++ AT91_PIOD 9 AT91_PERIPH_A AT91_PINCTRL_PULL_UP /* PD9 periph A Data bit 3 */
++ AT91_PIOD 10 AT91_PERIPH_A AT91_PINCTRL_PULL_UP /* PD10 periph A Data bit 4 */
++ AT91_PIOD 11 AT91_PERIPH_A AT91_PINCTRL_PULL_UP /* PD11 periph A Data bit 5 */
++ AT91_PIOD 12 AT91_PERIPH_A AT91_PINCTRL_PULL_UP /* PD12 periph A Data bit 6 */
++ AT91_PIOD 13 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>; /* PD13 periph A Data bit 7 */
++ };
++
++ pinctrl_nand_16bits: nand_16bits-0 {
++ atmel,pins =
++ <AT91_PIOD 14 AT91_PERIPH_A AT91_PINCTRL_PULL_UP /* PD14 periph A Data bit 8 */
++ AT91_PIOD 15 AT91_PERIPH_A AT91_PINCTRL_PULL_UP /* PD15 periph A Data bit 9 */
++ AT91_PIOD 16 AT91_PERIPH_A AT91_PINCTRL_PULL_UP /* PD16 periph A Data bit 10 */
++ AT91_PIOD 17 AT91_PERIPH_A AT91_PINCTRL_PULL_UP /* PD17 periph A Data bit 11 */
++ AT91_PIOD 18 AT91_PERIPH_A AT91_PINCTRL_PULL_UP /* PD18 periph A Data bit 12 */
++ AT91_PIOD 19 AT91_PERIPH_A AT91_PINCTRL_PULL_UP /* PD19 periph A Data bit 13 */
++ AT91_PIOD 20 AT91_PERIPH_A AT91_PINCTRL_PULL_UP /* PD20 periph A Data bit 14 */
++ AT91_PIOD 21 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>; /* PD21 periph A Data bit 15 */
++ };
++ };
++
++ 1wire_cm {
++ pinctrl_1wire_cm: 1wire_cm-0 {
++ atmel,pins = <AT91_PIOB 18 AT91_PERIPH_GPIO AT91_PINCTRL_MULTI_DRIVE>; /* PB18 multidrive, conflicts with led */
++ };
++ };
++ };
++
++ rtc@fffffeb0 {
++ status = "okay";
++ };
++
++ i2c0: i2c@f8010000 {
++ compatible = "i2c-gpio";
++ status = "okay";
++
++ id_eeprom@56 {
++ compatible = "atmel,24c04";
++ reg = <0x56>;
++ pagesize = <16>;
++ };
++ };
++
++ dbgu: serial@fffff200 {
++ status = "okay";
++ };
++
++ uart0: serial@f8040000 {
++ status = "okay";
++ };
++ usb2: gadget@f803c000 {
++ atmel,vbus-gpio = <&pioB 16 GPIO_ACTIVE_HIGH>;
++ status = "okay";
++ };
++ watchdog@fffffe40 {
++ status = "okay";
++ };
++ };
++
++ nand0: nand@40000000 {
++ nand-bus-width = <8>;
++ nand-ecc-mode = "hw";
++ atmel,has-pmecc; /* Enable PMECC */
++ atmel,pmecc-sector-size = <512>;
++ status = "okay";
++ reg = < 0x40000000 0x10000000
++ 0xffffe000 0x600 /* PMECC Registers */
++ 0xffffe600 0x200 /* PMECC Error Location Registers */
++ 0x00100000 0x100000 /* PMECC looup table in ROM code */
++ >;
++ atmel,pmecc-lookup-table-offset = <0x8000 0x10000>;
++ gpios = < &pioC 31 GPIO_ACTIVE_HIGH
++ &pioD 4 GPIO_ACTIVE_HIGH
++ 0
++ >;
++ atmel,pmecc-cap = <4>;
++ atmel,nand-has-dma;
++
++ nand@0 {
++ label = "NANDFlash";
++ reg = <0x0 0x10000000>;
++ };
++ at91bootstrap@0 {
++ label = "at91bootstrap";
++ reg = <0x0 0x40000>;
++ };
++ uboot@40000 {
++ label = "u-Boot";
++ reg = <0x40000 0x80000>;
++ };
++ ubootconfig0@c0000 {
++ label = "u-Boot Config";
++ reg = <0xc0000 0xa0000>;
++ };
++ ubootconfig1@160000 {
++ label = "u-Boot Redundant Config";
++ reg = <0x160000 0xa0000>;
++ };
++ uImage@200000 {
++ label = "uImage";
++ reg = <0x200000 0x600000>;
++ };
++ config0@800000 {
++ label = "Config";
++ reg = <0x800000 0x800000>;
++ };
++ config1@1000000 {
++ label = "OEM Config";
++ reg = <0x1000000 0x800000>;
++ };
++ rootfs@1800000 {
++ label = "Rootfs";
++ reg = <0x1800000 0xe800000>;
++ };
++ };
++
++ usb0: ohci@00600000 {
++ status = "okay";
++ num-ports = <3>;
++ };
++
++ usb1: ehci@00700000 {
++ status = "okay";
++ };
++ };
++
++ leds {
++ compatible = "gpio-leds";
++
++ pc21 {
++ label = "led-status";
++ gpios = <&pioC 21 GPIO_ACTIVE_LOW>;
++ linux,default-trigger = "default-on";
++ };
++ pc15 {
++ label = "led-b";
++ gpios = <&pioC 15 GPIO_ACTIVE_LOW>;
++ };
++ pc20 {
++ label = "led-c";
++ gpios = <&pioC 20 GPIO_ACTIVE_LOW>;
++ };
++ pc19 {
++ label = "led-d";
++ gpios = <&pioC 19 GPIO_ACTIVE_LOW>;
++ };
++ pc18 {
++ label = "led-e";
++ gpios = <&pioC 18 GPIO_ACTIVE_LOW>;
++ };
++ pc17 {
++ label = "led-f";
++ gpios = <&pioC 17 GPIO_ACTIVE_LOW>;
++ };
++ };
++
++ 1wire_cm {
++ compatible = "w1-gpio";
++ gpios = <&pioB 18 GPIO_ACTIVE_HIGH>;
++ linux,open-drain;
++ pinctrl-names = "default";
++ pinctrl-0 = <&pinctrl_1wire_cm>;
++ status = "okay";
++ };
++
++ i2c@0 {
++ status = "okay";
++
++ id_eeprom@56 {
++ compatible = "atmel,24c04";
++ reg = <0x56>;
++ pagesize = <16>;
++ };
++ };
++};
+diff --git a/arch/arm/mach-at91/board-dt-sam9.c b/arch/arm/mach-at91/board-dt-sam9.c
+index 8db3013..49ae83d 100644
+--- a/arch/arm/mach-at91/board-dt-sam9.c
++++ b/arch/arm/mach-at91/board-dt-sam9.c
+@@ -14,6 +14,8 @@
+ #include <linux/of.h>
+ #include <linux/of_irq.h>
+ #include <linux/of_platform.h>
++#include <linux/wl12xx.h>
++#include <linux/delay.h>
+
+ #include <asm/setup.h>
+ #include <asm/irq.h>
+@@ -37,11 +39,51 @@ static void __init at91_dt_init_irq(void)
+ of_irq_init(irq_of_match);
+ }
+
++static void mtr_wl12xx_set_power(bool enable)
++{
++ if (enable) {
++ gpio_set_value(AT91_PIN_PA27, 0);
++ msleep(10);
++ gpio_set_value(AT91_PIN_PA27, 1);
++ msleep(100);
++ pr_info("sam9x5: WLAN Enabled\n");
++ }
++ else {
++ gpio_set_value(AT91_PIN_PA27, 0);
++ msleep(10);
++ pr_info("sam9x5: WLAN Disabled\n");
++ }
++};
++
++static struct wl12xx_platform_data mtr_wl12xx_wlan_data __initdata = {
++ .set_power = mtr_wl12xx_set_power,
++ .irq = -1,
++ .board_ref_clock = WL12XX_REFCLOCK_38,
++ .platform_quirks = WL12XX_PLATFORM_QUIRK_EDGE_IRQ,
++};
++
++static void __init mtr_wl12xx_init(void) {
++ if (gpio_request_one(AT91_PIN_PA26, GPIOF_IN_DEGLITCH, "wlan-irq"))
++ pr_err("error request wl12xx irq gpio\n");
++
++ mtr_wl12xx_wlan_data.irq = gpio_to_irq(AT91_PIN_PA26);
++ if (mtr_wl12xx_wlan_data.irq < 0)
++ pr_err("error setting wl12xx irq\n");
++
++ if (wl12xx_set_platform_data(&mtr_wl12xx_wlan_data))
++ pr_err("error setting wl12xx data\n");
++}
++
+ static void __init at91_dt_device_init(void)
+ {
+ of_platform_populate(NULL, of_default_bus_match_table, NULL, NULL);
+ }
+
++static void __init at91_dt_device_init_late(void)
++{
++ mtr_wl12xx_init();
++}
++
+ static const char *at91_dt_board_compat[] __initdata = {
+ "atmel,at91sam9",
+ NULL
+@@ -55,5 +97,6 @@ DT_MACHINE_START(at91sam_dt, "Atmel AT91SAM (Device Tree)")
+ .init_early = at91_dt_initialize,
+ .init_irq = at91_dt_init_irq,
+ .init_machine = at91_dt_device_init,
++ .init_late = at91_dt_device_init_late,
+ .dt_compat = at91_dt_board_compat,
+ MACHINE_END
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-01 01:01:22 +0000