path: root/multitech/recipes/linux/linux-2.6.32/mt100eocg/linux-2.6.32.3-mach-at91-mt100eocg.patch

diff -uprN -X linux-2.6.32.3/Documentation/dontdiff linux-2.6.32.3-vanilla/arch/arm/mach-at91/at91sam9260_devices.c linux-2.6.32.3/arch/arm/mach-at91/at91sam9260_devices.c
--- linux-2.6.32.3-vanilla/arch/arm/mach-at91/at91sam9260_devices.c	2010-01-06 17:07:45.000000000 -0600
+++ linux-2.6.32.3/arch/arm/mach-at91/at91sam9260_devices.c	2010-10-11 10:15:08.000000000 -0500
@@ -183,9 +183,9 @@ void __init at91_add_device_eth(struct a
 		at91_set_B_periph(AT91_PIN_PA25, 0);	/* ERX2 */
 		at91_set_B_periph(AT91_PIN_PA26, 0);	/* ERX3 */
 		at91_set_B_periph(AT91_PIN_PA27, 0);	/* ERXCK */
-		at91_set_B_periph(AT91_PIN_PA23, 0);	/* ETX2 */
-		at91_set_B_periph(AT91_PIN_PA24, 0);	/* ETX3 */
-		at91_set_B_periph(AT91_PIN_PA22, 0);	/* ETXER */
+		at91_set_B_periph(AT91_PIN_PA10, 0);	/* ETX2 */
+		at91_set_B_periph(AT91_PIN_PA11, 0);	/* ETX3  */
+		/*at91_set_B_periph(AT91_PIN_PA22, 0);*/	/* ETXER */
 	}
 
 	eth_data = *data;
@@ -571,7 +571,15 @@ static struct platform_device at91sam926
 	.num_resources	= ARRAY_SIZE(spi1_resources),
 };
 
-static const unsigned spi1_standard_cs[4] = { AT91_PIN_PB3, AT91_PIN_PC5, AT91_PIN_PC4, AT91_PIN_PC3 };
+static const unsigned spi1_standard_cs[7] = {
+	AT91_PIN_PB21, //cdp-embedded mapped to this one instead of AT91_PIN_PB3,
+	AT91_PIN_PC5,
+	AT91_PIN_PC4,
+	AT91_PIN_PC6,
+	AT91_PIN_PB12,
+	AT91_PIN_PB13,
+	AT91_PIN_PB16
+};
 
 void __init at91_add_device_spi(struct spi_board_info *devices, int nr_devices)
 {
diff -uprN -X linux-2.6.32.3/Documentation/dontdiff linux-2.6.32.3-vanilla/arch/arm/mach-at91/board-sam9g20ek.c linux-2.6.32.3/arch/arm/mach-at91/board-sam9g20ek.c
--- linux-2.6.32.3-vanilla/arch/arm/mach-at91/board-sam9g20ek.c	2010-01-06 17:07:45.000000000 -0600
+++ linux-2.6.32.3/arch/arm/mach-at91/board-sam9g20ek.c	2010-10-14 16:16:52.000000000 -0500
@@ -27,6 +27,11 @@
 #include <linux/gpio_keys.h>
 #include <linux/input.h>
 #include <linux/clk.h>
+#include <linux/i2c/at24.h>
+#include <linux/spi/eeprom.h>
+#include <linux/spi/flash.h>
+#include <linux/delay.h>
+#include <mach/at91_rtt.h>
 
 #include <mach/hardware.h>
 #include <asm/setup.h>
@@ -44,9 +49,12 @@
 #include "sam9_smc.h"
 #include "generic.h"
 
+static int i2c_present;
 
 static void __init ek_map_io(void)
 {
+	int tmp;
+
 	/* Initialize processor: 18.432 MHz crystal */
 	at91sam9260_initialize(18432000);
 
@@ -61,12 +69,55 @@ static void __init ek_map_io(void)
 	/* USART1 on ttyS2. (Rx, Tx, RTS, CTS) */
 	at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS);
 
+	/*
+	 * Reset any initiated i2c data transfers?
+	 */
+	at91_set_gpio_input(AT91_PIN_PA23, 0);
+	at91_set_gpio_output(AT91_PIN_PA24, 0);
+	for (tmp = 0; tmp < 11; tmp++) {
+		at91_set_gpio_value(AT91_PIN_PA24, 0);
+		udelay(20);
+		at91_set_gpio_value(AT91_PIN_PA24, 1);
+		udelay(20);
+	}
+	at91_set_gpio_input(AT91_PIN_PA24, 0);
+
+	/*
+	 * PA24 and PA23 are used as ID pins on MTCBA/MTCDP-0.0 and I2C pins on MTCDP-1.0.
+	 *
+	 *   MTCBA Rev. B: 0x01, C: 0x02, D: 0x03
+	 *   MTCDP Rev. A reads as 0x00 with TWCK and TWD pulled high
+	 *
+	 */
+	tmp = !at91_get_gpio_value(AT91_PIN_PA24) << 1 | !at91_get_gpio_value(AT91_PIN_PA23);
+
+	i2c_present = !tmp;
+
+	/*
+	 * The GPS receiver is either at US2 on MTCBA/MTCDP-0.0 and US3 on MTCDP-1.0.
+	 */
+	if (i2c_present) {
+		at91_register_uart(AT91SAM9260_ID_US3, 3, ATMEL_UART_CTS | ATMEL_UART_RTS);
+		printk(KERN_INFO "sam9g20: i2c available\n");
+	} else {
+		at91_register_uart(AT91SAM9260_ID_US2, 3, 0);
+		printk(KERN_INFO "sam9g20: i2c not available\n");
+	}
+
 	/* set serial console to ttyS0 (ie, DBGU) */
 	at91_set_serial_console(0);
 }
 
 static void __init ek_init_irq(void)
 {
+	/*
+	 * Ensure RTT interrupts are disabled
+	 */ 
+	u32 mr;
+	mr = __raw_readl(AT91_VA_BASE_SYS + AT91_RTT + AT91_RTT_MR);
+	__raw_writel(mr & ~(AT91_RTT_ALMIEN | AT91_RTT_RTTINCIEN),
+			AT91_VA_BASE_SYS + AT91_RTT + AT91_RTT_MR);
+
 	at91sam9260_init_interrupts(NULL);
 }
 
@@ -82,11 +133,38 @@ static struct at91_usbh_data __initdata 
  * USB Device port
  */
 static struct at91_udc_data __initdata ek_udc_data = {
-	.vbus_pin	= AT91_PIN_PC5,
-	.pullup_pin	= 0,		/* pull-up driven by UDC */
+	.vbus_pin	= AT91_PIN_PC12,
+	.pullup_pin	= 0,			/* pull-up driven by UDC */
 };
 
 
+#define MTS_EXT_AT25_TEST		0
+#if MTS_EXT_AT25_TEST
+static struct spi_eeprom at25040b = {
+	.byte_len	= SZ_4K / 8,
+	.name		= "at25040b",
+	.page_size	= 8,
+	.flags		= EE_ADDR1,
+};
+#endif
+
+#define MTS_EXT_STT25_TEST		0
+#if MTS_EXT_STT25_TEST
+static struct mtd_partition m25_partitions[] = {
+	{
+		.name	= "flash",
+		.offset	= 0x00000000,
+		.size	= MTDPART_SIZ_FULL,
+	},
+};
+
+static struct flash_platform_data m25_spi_flash_data = {
+	.type		= "sst25vf080b",
+	.nr_parts	= ARRAY_SIZE(m25_partitions),
+	.parts		= m25_partitions,
+};
+#endif
+
 /*
  * SPI devices.
  */
@@ -107,6 +185,54 @@ static struct spi_board_info ek_spi_devi
 	},
 #endif
 #endif
+	{
+		.modalias	= "mts-io-sout",
+		.chip_select	= 0,
+		.bus_num	= 1,
+	},
+	{
+		.modalias	= "mts-io-board-temp",
+		.chip_select	= 2,
+		.bus_num	= 1,
+	},
+	{
+		.modalias	= "mts-io-dout",
+		.chip_select	= 1,
+		.bus_num	= 1,
+	},
+	{
+		.modalias	= "mts-io-din",
+		.chip_select	= 4,
+		.bus_num	= 1,
+	},
+#if MTS_EXT_AT25_TEST
+	{
+		.modalias	= "at25",
+		.platform_data	= &at25040b,
+		.max_speed_hz	= 20 * 1000 * 1000,
+		.bus_num	= 1,
+		.chip_select	= 5,
+		.mode		= SPI_MODE_0,
+	},
+	{
+		.modalias	= "at25",
+		.platform_data	= &at25040b,
+		.max_speed_hz	= 20 * 1000 * 1000,
+		.bus_num	= 1,
+		.chip_select	= 6,
+		.mode		= SPI_MODE_0,
+	},
+#endif
+#if MTS_EXT_STT25_TEST
+	{
+		.modalias	= "m25p80",
+		.platform_data	= &m25_spi_flash_data,
+		.irq		= NO_IRQ,
+		.max_speed_hz	= 33 * 1000 * 1000,
+		.bus_num	= 1,
+		.chip_select	= 5,
+	},
+#endif
 };
 
 
@@ -115,7 +241,7 @@ static struct spi_board_info ek_spi_devi
  */
 static struct at91_eth_data __initdata ek_macb_data = {
 	.phy_irq_pin	= AT91_PIN_PA7,
-	.is_rmii	= 1,
+	.is_rmii	= 0,
 };
 
 
@@ -124,18 +250,48 @@ static struct at91_eth_data __initdata e
  */
 static struct mtd_partition __initdata ek_nand_partition[] = {
 	{
-		.name   = "Bootstrap",
-		.offset = 0,
-		.size   = 4 * SZ_1M,
+		.name	= "MTNCG-NANDFlash",
+		.offset	= 0,
+		.size	= 256*1024*1024,
+	},
+	{
+		.name	= "AT91Bootstrap",
+		.offset	= 0,
+		.size	= 128*1024,
 	},
 	{
-		.name	= "Partition 1",
-		.offset	= MTDPART_OFS_NXTBLK,
-		.size	= 60 * SZ_1M,
+		.name	= "UBoot",
+		.offset	= 128*1024,
+		.size	= 256*1024,
 	},
 	{
-		.name	= "Partition 2",
-		.offset	= MTDPART_OFS_NXTBLK,
+		.name	= "UBoot Config",
+		.offset	= 384*1024,
+		.size	= 128*1024,
+	},
+	{
+		.name	= "UBoot Redundant Config",
+		.offset	= 512*1024,
+		.size	= 128*1024,
+	},
+	{
+		.name	= "uImage",
+		.offset	= 640*1024,
+		.size	= 59*128*1024,
+	},
+	{
+		.name	= "Config",
+		.offset	= 64*128*1024,
+		.size	= 64*128*1024,
+	},
+	{
+		.name	= "Oem Config",
+		.offset	= 128*128*1024,
+		.size	= 64*128*1024,
+	},
+	{
+		.name	= "Rootfs",
+		.offset	= 192*128*1024,
 		.size	= MTDPART_SIZ_FULL,
 	},
 };
@@ -195,11 +351,13 @@ static void __init ek_add_device_nand(vo
 
 /*
  * MCI (SD/MMC)
- * det_pin, wp_pin and vcc_pin are not connected
+ * det_pin, wp_pin and vcc_pin are not connected for embedded cdp REV0
  */
 static struct at91_mmc_data __initdata ek_mmc_data = {
 	.slot_b		= 1,
 	.wire4		= 1,
+//	.det_pin	= AT91_PIN_PA6,
+//	.wp_pin		= AT91_PIN_PA9,
 };
 
 
@@ -207,15 +365,10 @@ static struct at91_mmc_data __initdata e
  * LEDs
  */
 static struct gpio_led ek_leds[] = {
-	{	/* "bottom" led, green, userled1 to be defined */
-		.name			= "ds5",
-		.gpio			= AT91_PIN_PA6,
+	{	/* "status" led, green */
+		.name			= "status",
+		.gpio			= AT91_PIN_PA30,
 		.active_low		= 1,
-		.default_trigger	= "none",
-	},
-	{	/* "power" led, yellow */
-		.name			= "ds1",
-		.gpio			= AT91_PIN_PA9,
 		.default_trigger	= "heartbeat",
 	}
 };
@@ -269,15 +422,37 @@ static void __init ek_add_device_buttons
 static void __init ek_add_device_buttons(void) {}
 #endif
 
+uint8_t mts_id_eeprom[512];
+
+EXPORT_SYMBOL(mts_id_eeprom);
+
+static void mts_id_eeprom_load(struct memory_accessor *macc, void *context)
+{
+	int tmp;
+
+	memset(mts_id_eeprom, 0, sizeof(mts_id_eeprom));
+
+	tmp = macc->read(macc, mts_id_eeprom, 0, sizeof(mts_id_eeprom));
+	if (tmp != sizeof(mts_id_eeprom)) {
+		printk(KERN_ERR "sam9g20: id eeprom read failed: %d\n", tmp);
+	} else {
+		printk(KERN_INFO "sam9g20: read %d bytes from id eeprom\n", tmp);
+	}
+}
+
+static struct at24_platform_data at24c04_data = {
+	.byte_len	= SZ_4K / 8,
+	.page_size	= 16,
+	.setup		= mts_id_eeprom_load,
+};
 
 static struct i2c_board_info __initdata ek_i2c_devices[] = {
 	{
-		I2C_BOARD_INFO("24c512", 0x50),
-		I2C_BOARD_INFO("wm8731", 0x1b),
+		I2C_BOARD_INFO("24c04", 0x56),
+		.platform_data = &at24c04_data,
 	},
 };
 
-
 static void __init ek_board_init(void)
 {
 	/* Serial */
@@ -303,7 +478,7 @@ static void __init ek_board_init(void)
 	/* PCK0 provides MCLK to the WM8731 */
 	at91_set_B_periph(AT91_PIN_PC1, 0);
 	/* SSC (for WM8731) */
-	at91_add_device_ssc(AT91SAM9260_ID_SSC, ATMEL_SSC_TX);
+	/* at91_add_device_ssc(AT91SAM9260_ID_SSC, ATMEL_SSC_TX); */
 }
 
 MACHINE_START(AT91SAM9G20EK, "Atmel AT91SAM9G20-EK")