summaryrefslogtreecommitdiff
path: root/recipes-connectivity/lora/lora-gateway/library.cfg
blob: 01b066de4cbde5203971b3d43613fbb3a883094c (plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
# That file will be included in the Makefile files that have hardware dependencies

### SPI interface to the concentrator ###
# Accepted values:
#	native		Linux native SPI driver (/dev/spidev32766.0)
#	ftdi		FTDI SPI-over-USB bridge using libmpsse/libftdi/libusb

CFG_SPI= ftdi
CFG_SPI_DEV = "/dev/spidev32766.2"

### Concentrator chip ###
# Accepted values:
#	sx1301		Semtech SX1301 production chip
#	fpga1301	FPGA containing the SX1301 IP

CFG_CHIP= sx1301

### Radio chip(s) ###
# Accepted values:
#	sx1257		Dual SX1257 transceivers, covering 860-1000 MHz
#	sx1255		Dual SX1255 transceivers, covering 400-510 MHz

CFG_RADIO= sx1257

### RF band configuration ###
# Used to configured frequency restrictions (eg. if a SAW filter is installed)
# Accepted values:
#	full		Full range supported by the radio(s)
#	eu868		ETSI 868 (866) MHz band
#	us915		FCC 915 MHz band
#	cn470		China 470 MHz band
#	eu433		ETSI 433 MHz band
#	cn780		China 780 MHz band

CFG_BAND= full

### Board misc parameters & calibration ###
# Used to configure misc board options.
# RX RSSI indication and TX power are highly dependant on radio, band, filter
# and RF front-ends, and must be calibrated for each new board design.
# Available calibration parameters:
#	dev_nano_868		FPGA-based nano-concentrator, with 868 MHz SAW filter
#	ref_1301_868		SX1301 reference board with SX1257 radios, 868 MHz filters
#	ref_1301_433		SX1301 reference board with SX1255 radios, 433 MHz filters
#	kerlink_868			Kerlink LoRa 868MHz gateway
#	kerlink_433			Kerlink LoRa 433MHz gateway
#	cisco_433			Cisco LoRa 433MHz gateway
#	cisco_470			Cisco LoRa 470MHz gateway
#	cisco_780			Cisco LoRa 780MHz gateway
# Keep empty for no calibration parameters (neutral values will be used).

# MTAC-LORA 900MHz
CFG_BRD= mtaclora

### Network Type ###
# Accepted values:
#	private			Default
#	lora_mac		Only compliant with devices running LoRa MAC

CFG_NET= private

### Debug options ###
# Set the DEBUG_* to 1 to activate debug mode in individual modules.
# Warning: that makes the module *very verbose*, do not use for production

DEBUG_AUX= 0
DEBUG_SPI= 0
DEBUG_REG= 0
# jjg - turning this on is useful to get HAL-related error messages that 
# don't print out otherwise.  It doesn't seem to add that much printing
# under normal operation.
DEBUG_HAL= 1
DEBUG_GPS= 0