blob: 1b6188753e8564b536c87fa95da51520c5687e5d (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
|
#@TYPE: Machine
#@Name: Compulab cm-x270
#@DESCRIPTION: Machine configuration for Compulab cm-x270 computer module
#OLDEST_KERNEL = "2.6.16"
TARGET_ARCH = "arm"
GUI_MACHINE_CLASS ?= "bigscreen"
PREFERRED_PROVIDER_virtual/kernel = "linux"
PREFERRED_VERSION_linux ?= "2.6.23"
PACKAGE_EXTRA_ARCHS = "armv4 armv4t armv5te iwmmxt"
require conf/machine/include/tune-xscale.inc
# console serial port. If you have a L module
# the below works. If you have a W module, add
# the following line to your local.conf:
# CMX270_CONSOLE_SERIAL_PORT = "ttyS0"
# NAND flash eraseblock size
# most of the older cm-x270 modules are populated with NAND flash
# that have 128KiB eraseblocks. Recently, a user encounted
# a device that has 16KiB eraseblocks. The following define
# can be overridden in local.conf if you have one of these devices.
CMX270_NAND_ERASEBLOCK_SIZE ?= "0x20000"
# the following is for the cm-x270 L module
CMX270_CONSOLE_SERIAL_PORT ?= "ttyS1"
# used by sysvinit_2 package, so rebuild this
# package if you change the SERIAL_CONSOLE setting
# the following is the port for the cm-x270 L module
# I think the W module would use ttyS0, but has
# not been tested. This can be overwritten in
# local.conf
SERIAL_CONSOLE ?= "38400 ${CMX270_CONSOLE_SERIAL_PORT}"
# used by opie-collections.inc
ROOT_FLASH_SIZE ?= "32"
# for NAND flash.
EXTRA_IMAGECMD_jffs2 = "--little-endian --eraseblock=${CMX270_NAND_ERASEBLOCK_SIZE} --pad --no-cleanmarkers;\
sumtool -i ${DEPLOY_DIR_IMAGE}/${IMAGE_NAME}.rootfs.jffs2 \
-o ${DEPLOY_DIR_IMAGE}/${IMAGE_NAME}.rootfs-summary.jffs2 \
-e ${CMX270_NAND_ERASEBLOCK_SIZE} -p; \
cd ${DEPLOY_DIR_IMAGE}; \
rm -f ${DEPLOY_DIR_IMAGE}/${IMAGE_LINK_NAME}.rootfs-summary.jffs2; \
ln -s ${IMAGE_NAME}.rootfs-summary.jffs2 ${IMAGE_LINK_NAME}.rootfs-summary.jffs2 \
"
MACHINE_FEATURES = "kernel26 pcmcia usbhost usbgadget pcmcia touchscreen alsa iwmmxt"
# to program the compulab NAND flash, the following scheme is suggested. Create
# a small rootfs that can fit in NOR flash using the following config:
# - Angstrom distro
# - uclibc (set ANGSTROM_MODE = "uclibc" in local.conf)
# - angstrom-minimal-image-with-mtd-utils bitbake target
# - put the following in your local.conf
# - IMAGE_FSTYPES = "jffs2 tar cpio.gz"
# now, when you build the image, a cpio.gz will be generated
# that can be used as an initramfs. You can boot into this image and then
# program the main rootfs jffs2 image in NAND flash using mtd-utils
# you can select booting the initramfs, or the main nand rootfs by using
# the "ramdisk on", or "ramdisk off" commands in the bootloader
#
|
