1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
|
--- /tmp/board-omap3beagle.c 2009-08-13 12:35:01.000000000 +0200
+++ git/arch/arm/mach-omap2/board-omap3beagle.c 2009-08-13 12:44:00.000000000 +0200
@@ -21,6 +21,7 @@
#include <linux/io.h>
#include <linux/leds.h>
#include <linux/gpio.h>
+#include <linux/irq.h>
#include <linux/input.h>
#include <linux/gpio_keys.h>
@@ -54,6 +55,47 @@
#define GPMC_CS_SIZE 0x30
#define NAND_BLOCK_SIZE SZ_128K
+#if defined(CONFIG_ENC28J60) || defined(CONFIG_ENC28J60_MODULE)
+
+#include <mach/mcspi.h>
+#include <linux/spi/spi.h>
+
+#define OMAP3BEAGLE_GPIO_ENC28J60_IRQ 157
+
+static struct omap2_mcspi_device_config enc28j60_spi_chip_info = {
+ .turbo_mode = 0,
+ .single_channel = 1, /* 0: slave, 1: master */
+};
+
+static struct spi_board_info omap3beagle_spi_board_info[] __initdata = {
+ {
+ .modalias = "enc28j60",
+ .bus_num = 4,
+ .chip_select = 0,
+ .max_speed_hz = 20000000,
+ .controller_data = &enc28j60_spi_chip_info,
+ },
+};
+
+static void __init omap3beagle_enc28j60_init(void)
+{
+ if ((gpio_request(OMAP3BEAGLE_GPIO_ENC28J60_IRQ, "ENC28J60_IRQ") == 0) &&
+ (gpio_direction_input(OMAP3BEAGLE_GPIO_ENC28J60_IRQ) == 0)) {
+ gpio_export(OMAP3BEAGLE_GPIO_ENC28J60_IRQ, 0);
+ omap3beagle_spi_board_info[0].irq = OMAP_GPIO_IRQ(OMAP3BEAGLE_GPIO_ENC28J60_IRQ);
+ set_irq_type(omap3beagle_spi_board_info[0].irq, IRQ_TYPE_EDGE_FALLING);
+ } else {
+ printk(KERN_ERR "could not obtain gpio for ENC28J60_IRQ\n");
+ return;
+ }
+
+ spi_register_board_info(omap3beagle_spi_board_info,
+ ARRAY_SIZE(omap3beagle_spi_board_info));
+}
+
+#else
+static inline void __init omap3beagle_enc28j60_init(void) { return; }
+#endif
static struct mtd_partition omap3beagle_nand_partitions[] = {
/* All the partition sizes are listed in terms of NAND block size */
@@ -318,7 +360,7 @@
.vpll2 = &beagle_vpll2,
};
-static struct i2c_board_info __initdata beagle_i2c_boardinfo[] = {
+static struct i2c_board_info __initdata beagle_i2c1_boardinfo[] = {
{
I2C_BOARD_INFO("twl4030", 0x48),
.flags = I2C_CLIENT_WAKE,
@@ -327,10 +369,24 @@
},
};
+#if defined(CONFIG_RTC_DRV_DS1307) || \
+ defined(CONFIG_RTC_DRV_DS1307_MODULE)
+
+static struct i2c_board_info __initdata beagle_i2c2_boardinfo[] = {
+ {
+ I2C_BOARD_INFO("ds1307", 0x68),
+ },
+};
+#else
+static struct i2c_board_info __initdata beagle_i2c2_boardinfo[] = {};
+#endif
+
static int __init omap3_beagle_i2c_init(void)
{
- omap_register_i2c_bus(1, 2600, beagle_i2c_boardinfo,
- ARRAY_SIZE(beagle_i2c_boardinfo));
+ omap_register_i2c_bus(1, 2600, beagle_i2c1_boardinfo,
+ ARRAY_SIZE(beagle_i2c1_boardinfo));
+ omap_register_i2c_bus(2, 400, beagle_i2c2_boardinfo,
+ ARRAY_SIZE(beagle_i2c2_boardinfo));
/* Bus 3 is attached to the DVI port where devices like the pico DLP
* projector don't work reliably with 400kHz */
omap_register_i2c_bus(3, 100, NULL, 0);
@@ -542,6 +598,8 @@
omap_cfg_reg(J25_34XX_GPIO170);
+ omap3beagle_enc28j60_init();
+
usb_musb_init();
usb_ehci_init();
omap3beagle_flash_init();
|
