blob: e46061610d58430d43dfa30884d7d8a6c992c9eb (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
|
DESCRIPTION = "Linux Kernel"
SECTION = "kernel"
LICENSE = "GPL"
inherit kernel
RPSRC = "http://www.rpsys.net/openzaurus/patches/archive"
# Specify the commandline for your device
# Boot from mmc
CMDLINE_at91sam9263ek = "mem=64M console=ttyS0,115200 root=/dev/mmcblk0p1 rootfstype=ext2 rootdelay=5"
# Boot from nfs
#CMDLINE_at91sam9263ek = "mem=64M console=ttyS0,115200 root=301 root=/dev/nfs nfsroot=172.20.3.1:/data/at91 ip=172.20.0.5:::255.255.0.0"
# Set the verbosity of kernel messages during runtime
# You can define CMDLINE_DEBUG in your local.conf or distro.conf to override this behaviour
CMDLINE_DEBUG ?= '${@base_conditional("DISTRO_TYPE", "release", "quiet", "debug",d)}'
CMDLINE_append = " ${CMDLINE_DEBUG} "
do_configure_prepend() {
echo "" > ${S}/.config
#
# logo support, if you supply logo_linux_clut224.ppm in SRC_URI, then it's going to be used
#
if [ -e ${WORKDIR}/logo_linux_clut224.ppm ]; then
install -m 0644 ${WORKDIR}/logo_linux_clut224.ppm drivers/video/logo/logo_linux_clut224.ppm
echo "CONFIG_LOGO=y" >> ${S}/.config
echo "CONFIG_LOGO_LINUX_CLUT224=y" >> ${S}/.config
fi
#
# oabi / eabi support
#
if [ "${TARGET_OS}" = "linux-gnueabi" -o "${TARGET_OS}" = "linux-uclibcgnueabi" ]; then
echo "CONFIG_AEABI=y" >> ${S}/.config
echo "CONFIG_OABI_COMPAT=y" >> ${S}/.config
else
echo "# CONFIG_AEABI is not set" >> ${S}/.config
echo "# CONFIG_OABI_COMPAT is not set" >> ${S}/.config
fi
#
# endian support
#
if [ "${SITEINFO_ENDIANESS}" = "be" ]; then
echo "CONFIG_CPU_BIG_ENDIAN=y" >> ${S}/.config
fi
echo "CONFIG_CMDLINE=\"${CMDLINE}\"" >> ${S}/.config
sed -e '/CONFIG_AEABI/d' \
-e '/CONFIG_OABI_COMPAT=/d' \
-e '/CONFIG_CMDLINE=/d' \
-e '/CONFIG_CPU_BIG_ENDIAN/d' \
-e '/CONFIG_LOGO=/d' \
-e '/CONFIG_LOGO_LINUX_CLUT224=/d' \
-e '/CONFIG_LOCALVERSION/d' \
< '${WORKDIR}/defconfig' >>'${S}/.config'
#
# root-over-nfs-over-usb-eth support. Limited, but should cover some cases.
# Enable this by setting a proper CMDLINE_NFSROOT_USB.
#
if [ ! -z "${CMDLINE_NFSROOT_USB}" ]; then
oenote "Configuring the kernel for root-over-nfs-over-usb-eth with CMDLINE ${CMDLINE_NFSROOT_USB}"
sed -e '/CONFIG_INET/d' \
-e '/CONFIG_IP_PNP=/d' \
-e '/CONFIG_USB_GADGET=/d' \
-e '/CONFIG_USB_GADGET_SELECTED=/d' \
-e '/CONFIG_USB_ETH=/d' \
-e '/CONFIG_NFS_FS=/d' \
-e '/CONFIG_ROOT_NFS=/d' \
-e '/CONFIG_CMDLINE=/d' \
-i ${S}/.config
echo "CONFIG_INET=y" >> ${S}/.config
echo "CONFIG_IP_PNP=y" >> ${S}/.config
echo "CONFIG_USB_GADGET=y" >> ${S}/.config
echo "CONFIG_USB_GADGET_SELECTED=y" >> ${S}/.config
echo "CONFIG_USB_ETH=y" >> ${S}/.config
echo "CONFIG_NFS_FS=y" >> ${S}/.config
echo "CONFIG_ROOT_NFS=y" >> ${S}/.config
echo "CONFIG_CMDLINE=\"${CMDLINE_NFSROOT_USB}\"" >> ${S}/.config
fi
yes '' | oe_runmake oldconfig
}
do_configure_append_avr32() {
sed -i -e s:-mno-pic::g arch/avr32/Makefile
}
UBOOT_ENTRYPOINT ?= "20008000"
UBOOT_LOADADDRESS ?= "${UBOOT_ENTRYPOINT}"
do_compile_append() {
if test "x${KERNEL_IMAGETYPE}" = "xuImage" ; then
if test "x${ARCH}" = "xpowerpc" ; then
UBOOT_ARCH=ppc
else
UBOOT_ARCH=$ARCH
fi
if test -e arch/${ARCH}/boot/compressed/vmlinux ; then
${OBJCOPY} -O binary -R .note -R .comment -S arch/${ARCH}/boot/compressed/vmlinux linux.bin
uboot-mkimage -A ${UBOOT_ARCH} -O linux -T kernel -C none -a ${UBOOT_LOADADDRESS} -e ${UBOOT_ENTRYPOINT} -n "${DISTRO_NAME}/${PV}/${MACHINE}" -d linux.bin arch/${ARCH}/boot/uImage
rm -f linux.bin
else
${OBJCOPY} -O binary -R .note -R .comment -S vmlinux linux.bin
rm -f linux.bin.gz
gzip -9 linux.bin
uboot-mkimage -A ${UBOOT_ARCH} -O linux -T kernel -C gzip -a ${UBOOT_LOADADDRESS} -e ${UBOOT_ENTRYPOINT} -n "${DISTRO_NAME}/${PV}/${MACHINE}" -d linux.bin.gz arch/${ARCH}/boot/uImage
rm -f linux.bin.gz
fi
fi
}
KERNEL_IMAGE_BASE_NAME = "${KERNEL_IMAGETYPE}-${PV}-${PR}-${MACHINE}"
KERNEL_IMAGE_SYMLINK_NAME = "${KERNEL_IMAGETYPE}-${MACHINE}"
|
