diff -Nur u-boot-2006-04-18-1106/CREDITS u-boot-2006-04-18-1106-new/CREDITS --- u-boot-2006-04-18-1106/CREDITS 2006-04-18 09:05:03.000000000 +0000 +++ u-boot-2006-04-18-1106-new/CREDITS 2006-07-05 11:19:44.000000000 +0000 @@ -93,6 +93,12 @@ E: jonathan.debruyne@siemens.atea.be D: Port to Siemens IAD210 board +N: Alexander Chukov +E: sash@pdaXrom.org +D: initial support for Sharp Zaurus SL-C1000/3100 +D: initial support for Sharp Zaurus SL-C7x0/C860 +W: http://www.pdaXrom.org + N: Ken Chou E: kchou@ieee.org D: Support for A3000 SBC board diff -Nur u-boot-2006-04-18-1106/MAINTAINERS u-boot-2006-04-18-1106-new/MAINTAINERS --- u-boot-2006-04-18-1106/MAINTAINERS 2006-04-18 09:05:03.000000000 +0000 +++ u-boot-2006-04-18-1106-new/MAINTAINERS 2006-07-05 11:19:44.000000000 +0000 @@ -379,6 +379,11 @@ AT91RM9200DK at91rm9200 +Alexander Chukov + + akita xscale + corgi xscale + George G. Davis assabet SA1100 diff -Nur u-boot-2006-04-18-1106/MAKEALL u-boot-2006-04-18-1106-new/MAKEALL --- u-boot-2006-04-18-1106/MAKEALL 2006-04-18 09:05:03.000000000 +0000 +++ u-boot-2006-04-18-1106-new/MAKEALL 2006-07-05 11:19:44.000000000 +0000 @@ -206,7 +206,7 @@ adsvix cerf250 cradle csb226 \ delta innokom lubbock pxa255_idp \ wepep250 xaeniax xm250 xsengine \ - zylonite \ + zylonite akita corgi \ " LIST_ixp="ixdp425" diff -Nur u-boot-2006-04-18-1106/Makefile u-boot-2006-04-18-1106-new/Makefile --- u-boot-2006-04-18-1106/Makefile 2006-04-18 09:05:03.000000000 +0000 +++ u-boot-2006-04-18-1106-new/Makefile 2006-07-05 11:19:44.000000000 +0000 @@ -61,7 +61,7 @@ CROSS_COMPILE = powerpc-linux- endif ifeq ($(ARCH),arm) -CROSS_COMPILE = arm-linux- +CROSS_COMPILE = armv5tel-linux- endif ifeq ($(ARCH),i386) ifeq ($(HOSTARCH),i386) @@ -1709,6 +1709,12 @@ zylonite_config : @./mkconfig $(@:_config=) arm pxa zylonite +akita_config : unconfig + @./mkconfig $(@:_config=) arm pxa akita + +corgi_config : unconfig + @./mkconfig $(@:_config=) arm pxa corgi + ######################################################################### ## ARM1136 Systems ######################################################################### diff -Nur u-boot-2006-04-18-1106/README u-boot-2006-04-18-1106-new/README --- u-boot-2006-04-18-1106/README 2006-04-18 09:05:03.000000000 +0000 +++ u-boot-2006-04-18-1106-new/README 2006-07-05 11:19:44.000000000 +0000 @@ -311,7 +311,8 @@ CONFIG_KB9202, CONFIG_LART, CONFIG_LPD7A400, CONFIG_LUBBOCK, CONFIG_OSK_OMAP5912, CONFIG_OMAP2420H4, CONFIG_SHANNON, CONFIG_P2_OMAP730, CONFIG_SMDK2400, - CONFIG_SMDK2410, CONFIG_TRAB, CONFIG_VCMA9 + CONFIG_SMDK2410, CONFIG_TRAB, CONFIG_VCMA9, + CONFIG_AKITA, CONFIG_CORGI MicroBlaze based boards: ------------------------ diff -Nur u-boot-2006-04-18-1106/board/akita/Makefile u-boot-2006-04-18-1106-new/board/akita/Makefile --- u-boot-2006-04-18-1106/board/akita/Makefile 1970-01-01 00:00:00.000000000 +0000 +++ u-boot-2006-04-18-1106-new/board/akita/Makefile 2006-07-05 11:19:44.000000000 +0000 @@ -0,0 +1,51 @@ +# +# board/akita/Makefile +# +# (C) Copyright 2006 Alexander Chukov +# +# (C) Copyright 2000 +# Wolfgang Denk, DENX Software Engineering, wd@denx.de. +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +include $(TOPDIR)/config.mk + +LIB = lib$(BOARD).a + +OBJS := akita.o nand.o kbd.o +SOBJS := lowlevel_init.o + +$(LIB): $(OBJS) $(SOBJS) + $(AR) crv $@ $(OBJS) $(SOBJS) + +clean: + rm -f $(SOBJS) $(OBJS) + +distclean: clean + rm -f $(LIB) core *.bak .depend + +######################################################################### + +.depend: Makefile $(SOBJS:.o=.S) $(OBJS:.o=.c) + $(CC) -M $(CPPFLAGS) $(SOBJS:.o=.S) $(OBJS:.o=.c) > $@ + +-include .depend + +######################################################################### diff -Nur u-boot-2006-04-18-1106/board/akita/akita.c u-boot-2006-04-18-1106-new/board/akita/akita.c --- u-boot-2006-04-18-1106/board/akita/akita.c 1970-01-01 00:00:00.000000000 +0000 +++ u-boot-2006-04-18-1106-new/board/akita/akita.c 2006-07-05 11:19:44.000000000 +0000 @@ -0,0 +1,89 @@ +/* + * board/akita/akita.c + * + * Configuration settings for the Sharp Zaurus SL-Cxx00. + * + * (C) Copyright 2006 Alexander Chukov + * + * portions from adsvix board configuration: + * (C) Copyright 2004 + * Robert Whaley, Applied Data Systems, Inc. rwhaley@applieddata.net + * (C) Copyright 2002 + * Kyle Harris, Nexus Technologies, Inc. kharris@nexus-tech.net + * (C) Copyright 2002 + * Sysgo Real-Time Solutions, GmbH + * Marius Groeger + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include + +void set_turbo_mode(void); + +/* ------------------------------------------------------------------------- */ + +/* + * Miscellaneous platform dependent initialisations + */ + +int board_init (void) +{ + DECLARE_GLOBAL_DATA_PTR; + + /* memory and cpu-speed are setup before relocation */ + /* so we do _nothing_ here */ + + /* arch number of Sharp Zaurus Akita : MACH_TYPE_AKITA */ + gd->bd->bi_arch_number = 744; + + /* adress of boot parameters */ + gd->bd->bi_boot_params = 0xa0000100; + + /* set cpu turbo mode */ + set_turbo_mode(); + + spitzkbd_init(); + + return 0; +} + +int board_late_init(void) +{ + setenv("stdout", "serial"); + setenv("stderr", "serial"); + return 0; +} + + +int dram_init (void) +{ + DECLARE_GLOBAL_DATA_PTR; + + gd->bd->bi_dram[0].start = PHYS_SDRAM_1; + gd->bd->bi_dram[0].size = PHYS_SDRAM_1_SIZE; + gd->bd->bi_dram[1].start = PHYS_SDRAM_2; + gd->bd->bi_dram[1].size = PHYS_SDRAM_2_SIZE; + gd->bd->bi_dram[2].start = PHYS_SDRAM_3; + gd->bd->bi_dram[2].size = PHYS_SDRAM_3_SIZE; + gd->bd->bi_dram[3].start = PHYS_SDRAM_4; + gd->bd->bi_dram[3].size = PHYS_SDRAM_4_SIZE; + + return 0; +} diff -Nur u-boot-2006-04-18-1106/board/akita/config.mk u-boot-2006-04-18-1106-new/board/akita/config.mk --- u-boot-2006-04-18-1106/board/akita/config.mk 1970-01-01 00:00:00.000000000 +0000 +++ u-boot-2006-04-18-1106-new/board/akita/config.mk 2006-07-05 11:19:44.000000000 +0000 @@ -0,0 +1 @@ +TEXT_BASE = 0xa3000000 diff -Nur u-boot-2006-04-18-1106/board/akita/kbd.c u-boot-2006-04-18-1106-new/board/akita/kbd.c --- u-boot-2006-04-18-1106/board/akita/kbd.c 1970-01-01 00:00:00.000000000 +0000 +++ u-boot-2006-04-18-1106-new/board/akita/kbd.c 2006-07-05 11:19:44.000000000 +0000 @@ -0,0 +1,261 @@ +/* + * board/akita/kbd.c + * + * Keyboard driver for the Sharp Zaurus SL-Cxx00. + * + * (C) Copyright 2006 Alexander Chukov + * + * portions from: + * + * linux/drivers/input/keyboard/spitzkbd.c + * + * Keyboard driver for Sharp Spitz, Borzoi and Akita (SL-Cxx00 series) + * + * Copyright (C) 2005 Richard Purdie + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include +#include +#include +#include +#include + +#define GPIO_DFLT_LOW 0x400 +#define GPIO_DFLT_HIGH 0x800 + +void pxa_gpio_mode(int gpio_mode) +{ + int gpio = gpio_mode & GPIO_MD_MASK_NR; + int fn = (gpio_mode & GPIO_MD_MASK_FN) >> 8; + int gafr; + + if (gpio_mode & GPIO_DFLT_LOW) + GPCR(gpio) = GPIO_bit(gpio); + else if (gpio_mode & GPIO_DFLT_HIGH) + GPSR(gpio) = GPIO_bit(gpio); + if (gpio_mode & GPIO_MD_MASK_DIR) + GPDR(gpio) |= GPIO_bit(gpio); + else + GPDR(gpio) &= ~GPIO_bit(gpio); + gafr = GAFR(gpio) & ~(0x3 << (((gpio) & 0xf)*2)); + GAFR(gpio) = gafr | (fn << (((gpio) & 0xf)*2)); +} + +#define SPITZ_KEY_STROBE_NUM (11) +#define SPITZ_KEY_SENSE_NUM (7) + +#define SPITZ_GPIO_G0_STROBE_BIT 0x0f800000 +#define SPITZ_GPIO_G1_STROBE_BIT 0x00100000 +#define SPITZ_GPIO_G2_STROBE_BIT 0x01000000 +#define SPITZ_GPIO_G3_STROBE_BIT 0x00041880 +#define SPITZ_GPIO_G0_SENSE_BIT 0x00021000 +#define SPITZ_GPIO_G1_SENSE_BIT 0x000000d4 +#define SPITZ_GPIO_G2_SENSE_BIT 0x08000000 +#define SPITZ_GPIO_G3_SENSE_BIT 0x00000000 + +#define SPITZ_GPIO_KEY_STROBE0 88 +#define SPITZ_GPIO_KEY_STROBE1 23 +#define SPITZ_GPIO_KEY_STROBE2 24 +#define SPITZ_GPIO_KEY_STROBE3 25 +#define SPITZ_GPIO_KEY_STROBE4 26 +#define SPITZ_GPIO_KEY_STROBE5 27 +#define SPITZ_GPIO_KEY_STROBE6 52 +#define SPITZ_GPIO_KEY_STROBE7 103 +#define SPITZ_GPIO_KEY_STROBE8 107 +#define SPITZ_GPIO_KEY_STROBE9 108 +#define SPITZ_GPIO_KEY_STROBE10 114 + +#define SPITZ_GPIO_KEY_SENSE0 12 +#define SPITZ_GPIO_KEY_SENSE1 17 +#define SPITZ_GPIO_KEY_SENSE2 91 +#define SPITZ_GPIO_KEY_SENSE3 34 +#define SPITZ_GPIO_KEY_SENSE4 36 +#define SPITZ_GPIO_KEY_SENSE5 38 +#define SPITZ_GPIO_KEY_SENSE6 39 + +#define SPITZ_GPIO_ON_KEY (95) + +#define KB_ROWS 7 +#define KB_COLS 11 +#define KB_ROWMASK(r) (1 << (r)) +#define SCANCODE(r,c) (((r)<<4) + (c) + 1) +#define NR_SCANCODES ((KB_ROWS<<4) + 1) + +#define SCAN_INTERVAL (50) /* ms */ +#define HINGE_SCAN_INTERVAL (150) /* ms */ + +#define KB_DISCHARGE_DELAY 10 +#define KB_ACTIVATE_DELAY 10 + +static int spitz_strobes[] = { + SPITZ_GPIO_KEY_STROBE0, + SPITZ_GPIO_KEY_STROBE1, + SPITZ_GPIO_KEY_STROBE2, + SPITZ_GPIO_KEY_STROBE3, + SPITZ_GPIO_KEY_STROBE4, + SPITZ_GPIO_KEY_STROBE5, + SPITZ_GPIO_KEY_STROBE6, + SPITZ_GPIO_KEY_STROBE7, + SPITZ_GPIO_KEY_STROBE8, + SPITZ_GPIO_KEY_STROBE9, + SPITZ_GPIO_KEY_STROBE10, +}; + +static int spitz_senses[] = { + SPITZ_GPIO_KEY_SENSE0, + SPITZ_GPIO_KEY_SENSE1, + SPITZ_GPIO_KEY_SENSE2, + SPITZ_GPIO_KEY_SENSE3, + SPITZ_GPIO_KEY_SENSE4, + SPITZ_GPIO_KEY_SENSE5, + SPITZ_GPIO_KEY_SENSE6, +}; + +static inline void spitzkbd_discharge_all(void) +{ + /* STROBE All HiZ */ + GPCR0 = SPITZ_GPIO_G0_STROBE_BIT; + GPDR0 &= ~SPITZ_GPIO_G0_STROBE_BIT; + GPCR1 = SPITZ_GPIO_G1_STROBE_BIT; + GPDR1 &= ~SPITZ_GPIO_G1_STROBE_BIT; + GPCR2 = SPITZ_GPIO_G2_STROBE_BIT; + GPDR2 &= ~SPITZ_GPIO_G2_STROBE_BIT; + GPCR3 = SPITZ_GPIO_G3_STROBE_BIT; + GPDR3 &= ~SPITZ_GPIO_G3_STROBE_BIT; +} + +static inline void spitzkbd_activate_all(void) +{ + /* STROBE ALL -> High */ + GPSR0 = SPITZ_GPIO_G0_STROBE_BIT; + GPDR0 |= SPITZ_GPIO_G0_STROBE_BIT; + GPSR1 = SPITZ_GPIO_G1_STROBE_BIT; + GPDR1 |= SPITZ_GPIO_G1_STROBE_BIT; + GPSR2 = SPITZ_GPIO_G2_STROBE_BIT; + GPDR2 |= SPITZ_GPIO_G2_STROBE_BIT; + GPSR3 = SPITZ_GPIO_G3_STROBE_BIT; + GPDR3 |= SPITZ_GPIO_G3_STROBE_BIT; + + udelay(KB_DISCHARGE_DELAY); +} + +static inline void spitzkbd_activate_col(int col) +{ + int gpio = spitz_strobes[col]; + GPDR0 &= ~SPITZ_GPIO_G0_STROBE_BIT; + GPDR1 &= ~SPITZ_GPIO_G1_STROBE_BIT; + GPDR2 &= ~SPITZ_GPIO_G2_STROBE_BIT; + GPDR3 &= ~SPITZ_GPIO_G3_STROBE_BIT; + GPSR(gpio) = GPIO_bit(gpio); + GPDR(gpio) |= GPIO_bit(gpio); +} + +static inline void spitzkbd_reset_col(int col) +{ + int gpio = spitz_strobes[col]; + GPDR0 &= ~SPITZ_GPIO_G0_STROBE_BIT; + GPDR1 &= ~SPITZ_GPIO_G1_STROBE_BIT; + GPDR2 &= ~SPITZ_GPIO_G2_STROBE_BIT; + GPDR3 &= ~SPITZ_GPIO_G3_STROBE_BIT; + GPCR(gpio) = GPIO_bit(gpio); + GPDR(gpio) |= GPIO_bit(gpio); +} + +static inline int spitzkbd_get_row_status(int col) +{ + return ((GPLR0 >> 12) & 0x01) | ((GPLR0 >> 16) & 0x02) + | ((GPLR2 >> 25) & 0x04) | ((GPLR1 << 1) & 0x08) + | ((GPLR1 >> 0) & 0x10) | ((GPLR1 >> 1) & 0x60); +} + +static int spitzkbd_scankeyboard(void) +{ + unsigned int row, col, rowd; + unsigned int num_pressed, pwrkey = ((GPLR(SPITZ_GPIO_ON_KEY) & GPIO_bit(SPITZ_GPIO_ON_KEY)) != 0); + int ret = -1; + + num_pressed = 0; + for (col = 0; col < KB_COLS; col++) { + spitzkbd_discharge_all(); + udelay(KB_DISCHARGE_DELAY); + + spitzkbd_activate_col(col); + udelay(KB_ACTIVATE_DELAY); + + rowd = spitzkbd_get_row_status(col); + for (row = 0; row < KB_ROWS; row++) { + unsigned int scancode, pressed; + + scancode = SCANCODE(row, col); + pressed = rowd & KB_ROWMASK(row); + + if (pressed) + ret = scancode; + } + spitzkbd_reset_col(col); + } + + spitzkbd_activate_all(); + + if (pwrkey) + return -2; + + return ret; +} + +void spitzkbd_init(void) +{ + int i; + + /* Setup sense interrupts - RisingEdge Detect, sense lines as inputs */ + for (i = 0; i < SPITZ_KEY_SENSE_NUM; i++) + pxa_gpio_mode(spitz_senses[i] | GPIO_IN); + + /* Set Strobe lines as outputs - set high */ + for (i = 0; i < SPITZ_KEY_STROBE_NUM; i++) + pxa_gpio_mode(spitz_strobes[i] | GPIO_OUT | GPIO_DFLT_HIGH); + + pxa_gpio_mode(SPITZ_GPIO_ON_KEY | GPIO_IN); +} + +int do_testkey(cmd_tbl_t *cmdtp, int flag, int argc, char *argv[]) +{ + int scan; + + if (argc < 2) + return 1; + + scan = spitzkbd_scankeyboard(); + + +// if (scan >= 0) +// printf("Scan = %d\n", scan); +// else +// printf("Nothing!\n"); + + return !(simple_strtol(argv[1], NULL, 10) == scan); +} + +U_BOOT_CMD( + testkey, 2, 1, do_testkey, + "testkey - compare pressed key with arg\n", + "" +); diff -Nur u-boot-2006-04-18-1106/board/akita/lowlevel_init.S u-boot-2006-04-18-1106-new/board/akita/lowlevel_init.S --- u-boot-2006-04-18-1106/board/akita/lowlevel_init.S 1970-01-01 00:00:00.000000000 +0000 +++ u-boot-2006-04-18-1106-new/board/akita/lowlevel_init.S 2006-07-05 11:19:44.000000000 +0000 @@ -0,0 +1,135 @@ +/* + * board/akita/lowlevel_init.S + * + * Configuration settings for the Sharp Zaurus SL-Cxx00. + * + * (C) Copyright 2006 Alexander Chukov + * + * This was originally from the Lubbock u-boot port and from BLOB with cleanup + * + * NOTE: I haven't clean this up considerably, just enough to get it + * running. See hal_platform_setup.h for the source. See + * board/cradle/lowlevel_init.S for another PXA250 setup that is + * much cleaner. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include +#include +#include + +/* wait for coprocessor write complete */ + .macro CPWAIT reg + mrc p15,0,\reg,c2,c0,0 + mov \reg,\reg + sub pc,pc,#4 + .endm + +/*********** Write out to HEX 7 segment leds *********/ + +#undef DEBUG_HEXLOG + +#ifdef DEBUG_HEXLOG +#define LEDCTL 0x08000040 +#define LEDDAT1 0x08000010 +#define LEDDAT2 0x08000014 + +.macro wait, count + mov r10, \count +0: + subs r10, r10, #1 + bne 0b +.endm + +.macro hexlog_init + ldr r11, =LEDCTL + mov r10, #0xff + str r10, [r11] + ldr r11, =LEDDAT2 + mov r10, #0xFFFFFFFF + str r10, [r11] + ldr r11, =LEDDAT1 + mov r10, #0x0 + str r10, [r11] +.endm + +.macro hexlog, val + ldr r11, =LEDCTL + mov r10, #0xff + str r10, [r11] + ldr r11, =LEDDAT2 + mov r10, #0xFFFFFFFF + str r10, [r11] + + ldr r11, =LEDDAT1 + mov r10, \val + str r10, [r11] + + wait #0x400000 +.endm + +#else + +.macro hexlog_init + nop +.endm + +.macro hexlog, val + nop +.endm + +#endif + +/***********************************/ + +/* + * Memory setup + */ + +.globl lowlevel_init +lowlevel_init: + + mov pc, lr + +.globl set_turbo_mode + +set_turbo_mode: + /* Turn on turbo mode */ + mrc p14, 0, r2, c6, c0, 0 + orr r2, r2, #0xB /* Turbo, Fast-Bus, Freq change**/ + mcr p14, 0, r2, c6, c0, 0 + + /* Setup vectors */ + ldr r0, =TEXT_BASE + ldr r1, =TEXT_BASE+0x40 + ldr r2, =0x0 +1: + ldr r3, [r0] + str r3, [r2] + add r0, r0, #4 + add r2, r2, #4 + cmp r0, r1 + bne 1b + + ldr r0, =0x0 + ldr r1, [r0, #4] + str r1, [r0] + + mov pc, lr diff -Nur u-boot-2006-04-18-1106/board/akita/nand.c u-boot-2006-04-18-1106-new/board/akita/nand.c --- u-boot-2006-04-18-1106/board/akita/nand.c 1970-01-01 00:00:00.000000000 +0000 +++ u-boot-2006-04-18-1106-new/board/akita/nand.c 2006-07-05 11:19:44.000000000 +0000 @@ -0,0 +1,169 @@ +/* + * board/akita/nand.c + * + * NAND driver for the Sharp Zaurus SL-Cxx00. + * + * (C) Copyright 2006 Alexander Chukov + * + * portions from mtd nand driver: + * + * drivers/mtd/nand/sharpsl.c + * + * Copyright (C) 2004 Richard Purdie + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include + + +#if (CONFIG_COMMANDS & CFG_CMD_NAND) + +#include +#include + +static int sharpsl_io_base = CFG_NAND_BASE; + +/* register offset */ +#define ECCLPLB sharpsl_io_base+0x00 /* line parity 7 - 0 bit */ +#define ECCLPUB sharpsl_io_base+0x04 /* line parity 15 - 8 bit */ +#define ECCCP sharpsl_io_base+0x08 /* column parity 5 - 0 bit */ +#define ECCCNTR sharpsl_io_base+0x0C /* ECC byte counter */ +#define ECCCLRR sharpsl_io_base+0x10 /* cleare ECC */ +#define FLASHIO sharpsl_io_base+0x14 /* Flash I/O */ +#define FLASHCTL sharpsl_io_base+0x18 /* Flash Control */ + +/* Flash control bit */ +#define FLRYBY (1 << 5) +#define FLCE1 (1 << 4) +#define FLWP (1 << 3) +#define FLALE (1 << 2) +#define FLCLE (1 << 1) +#define FLCE0 (1 << 0) + +#define readb(address) *((volatile unsigned char *)(address)) +#define writeb(v, address) *((volatile unsigned char *)(address))=v + +/* + * hardware specific access to control-lines + */ +static void +sharpsl_nand_hwcontrol(struct mtd_info* mtd, int cmd) +{ + switch (cmd) { + case NAND_CTL_SETCLE: + writeb(readb(FLASHCTL) | FLCLE, FLASHCTL); + break; + case NAND_CTL_CLRCLE: + writeb(readb(FLASHCTL) & ~FLCLE, FLASHCTL); + break; + + case NAND_CTL_SETALE: + writeb(readb(FLASHCTL) | FLALE, FLASHCTL); + break; + case NAND_CTL_CLRALE: + writeb(readb(FLASHCTL) & ~FLALE, FLASHCTL); + break; + + case NAND_CTL_SETNCE: + writeb(readb(FLASHCTL) & ~(FLCE0|FLCE1), FLASHCTL); + break; + case NAND_CTL_CLRNCE: + writeb(readb(FLASHCTL) | (FLCE0|FLCE1), FLASHCTL); + break; + } +} + +static int +sharpsl_nand_dev_ready(struct mtd_info* mtd) +{ + return !((readb(FLASHCTL) & FLRYBY) == 0); +} + +static void +sharpsl_nand_enable_hwecc(struct mtd_info* mtd, int mode) +{ + writeb(0 ,ECCCLRR); +} + +static int +sharpsl_nand_calculate_ecc(struct mtd_info* mtd, const u_char* dat, + u_char* ecc_code) +{ + ecc_code[0] = ~readb(ECCLPUB); + ecc_code[1] = ~readb(ECCLPLB); + ecc_code[2] = (~readb(ECCCP) << 2) | 0x03; + return readb(ECCCNTR) != 0; +} + +static uint8_t scan_ff_pattern[] = { 0xff, 0xff }; + +static struct nand_bbt_descr sharpsl_akita_bbt = { + .options = 0, + .offs = 4, + .len = 1, + .pattern = scan_ff_pattern +}; + +static struct nand_oobinfo akita_oobinfo = { + .useecc = MTD_NANDECC_AUTOPLACE, + .eccbytes = 24, + .eccpos = { + 0x5, 0x1, 0x2, 0x3, 0x6, 0x7, 0x15, 0x11, + 0x12, 0x13, 0x16, 0x17, 0x25, 0x21, 0x22, 0x23, + 0x26, 0x27, 0x35, 0x31, 0x32, 0x33, 0x36, 0x37}, + .oobfree = { {0x08, 0x09} } +}; + +/* + * Board-specific NAND initialization. The following members of the + * argument are board-specific (per include/linux/mtd/nand.h): + * - IO_ADDR_R?: address to read the 8 I/O lines of the flash device + * - IO_ADDR_W?: address to write the 8 I/O lines of the flash device + * - hwcontrol: hardwarespecific function for accesing control-lines + * - dev_ready: hardwarespecific function for accesing device ready/busy line + * - enable_hwecc?: function to enable (reset) hardware ecc generator. Must + * only be provided if a hardware ECC is available + * - eccmode: mode of ecc, see defines + * - chip_delay: chip dependent delay for transfering data from array to + * read regs (tR) + * - options: various chip options. They can partly be set to inform + * nand_scan about special functionality. See the defines for further + * explanation + * Members with a "?" were not set in the merged testing-NAND branch, + * so they are not set here either. + */ +void board_nand_init(struct nand_chip *nand) +{ + writeb(readb(FLASHCTL) | FLWP, FLASHCTL); + + nand->IO_ADDR_R = FLASHIO; + nand->IO_ADDR_W = FLASHIO; + nand->hwcontrol = sharpsl_nand_hwcontrol; + nand->dev_ready = sharpsl_nand_dev_ready; + nand->eccmode = NAND_ECC_HW3_256; + nand->chip_delay = 15; + nand->options = NAND_SAMSUNG_LP_OPTIONS; + nand->badblock_pattern = &sharpsl_akita_bbt; + nand->autooob = &akita_oobinfo; + nand->enable_hwecc = sharpsl_nand_enable_hwecc; + nand->calculate_ecc = sharpsl_nand_calculate_ecc; + nand->correct_data = nand_correct_data; +} +#endif /* (CONFIG_COMMANDS & CFG_CMD_NAND) */ diff -Nur u-boot-2006-04-18-1106/board/akita/u-boot.lds u-boot-2006-04-18-1106-new/board/akita/u-boot.lds --- u-boot-2006-04-18-1106/board/akita/u-boot.lds 1970-01-01 00:00:00.000000000 +0000 +++ u-boot-2006-04-18-1106-new/board/akita/u-boot.lds 2006-07-05 11:19:44.000000000 +0000 @@ -0,0 +1,56 @@ +/* + * (C) Copyright 2000 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +OUTPUT_FORMAT("elf32-littlearm", "elf32-littlearm", "elf32-littlearm") +OUTPUT_ARCH(arm) +ENTRY(_start) +SECTIONS +{ + . = 0x00000000; + + . = ALIGN(4); + .text : + { + cpu/pxa/start.o (.text) + *(.text) + } + + . = ALIGN(4); + .rodata : { *(.rodata) } + + . = ALIGN(4); + .data : { *(.data) } + + . = ALIGN(4); + .got : { *(.got) } + + . = .; + __u_boot_cmd_start = .; + .u_boot_cmd : { *(.u_boot_cmd) } + __u_boot_cmd_end = .; + + . = ALIGN(4); + __bss_start = .; + .bss : { *(.bss) } + _end = .; +} diff -Nur u-boot-2006-04-18-1106/board/corgi/Makefile u-boot-2006-04-18-1106-new/board/corgi/Makefile --- u-boot-2006-04-18-1106/board/corgi/Makefile 1970-01-01 00:00:00.000000000 +0000 +++ u-boot-2006-04-18-1106-new/board/corgi/Makefile 2006-07-05 11:19:44.000000000 +0000 @@ -0,0 +1,51 @@ +# +# board/corgi/Makefile +# +# (C) Copyright 2006 Alexander Chukov +# +# (C) Copyright 2000 +# Wolfgang Denk, DENX Software Engineering, wd@denx.de. +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +include $(TOPDIR)/config.mk + +LIB = lib$(BOARD).a + +OBJS := corgi.o nand.o kbd.o +SOBJS := lowlevel_init.o + +$(LIB): $(OBJS) $(SOBJS) + $(AR) crv $@ $(OBJS) $(SOBJS) + +clean: + rm -f $(SOBJS) $(OBJS) + +distclean: clean + rm -f $(LIB) core *.bak .depend + +######################################################################### + +.depend: Makefile $(SOBJS:.o=.S) $(OBJS:.o=.c) + $(CC) -M $(CPPFLAGS) $(SOBJS:.o=.S) $(OBJS:.o=.c) > $@ + +-include .depend + +######################################################################### diff -Nur u-boot-2006-04-18-1106/board/corgi/config.mk u-boot-2006-04-18-1106-new/board/corgi/config.mk --- u-boot-2006-04-18-1106/board/corgi/config.mk 1970-01-01 00:00:00.000000000 +0000 +++ u-boot-2006-04-18-1106-new/board/corgi/config.mk 2006-07-05 11:19:44.000000000 +0000 @@ -0,0 +1 @@ +TEXT_BASE = 0xa1000000 diff -Nur u-boot-2006-04-18-1106/board/corgi/corgi.c u-boot-2006-04-18-1106-new/board/corgi/corgi.c --- u-boot-2006-04-18-1106/board/corgi/corgi.c 1970-01-01 00:00:00.000000000 +0000 +++ u-boot-2006-04-18-1106-new/board/corgi/corgi.c 2006-07-05 11:19:44.000000000 +0000 @@ -0,0 +1,87 @@ +/* + * board/corgi/corgi.c + * + * Configuration settings for the Sharp Zaurus SL-C7x0/860. + * + * (C) Copyright 2006 Alexander Chukov + * + * portions from adsvix board configuration: + * (C) Copyright 2004 + * Robert Whaley, Applied Data Systems, Inc. rwhaley@applieddata.net + * (C) Copyright 2002 + * Kyle Harris, Nexus Technologies, Inc. kharris@nexus-tech.net + * (C) Copyright 2002 + * Sysgo Real-Time Solutions, GmbH + * Marius Groeger + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include + +/* ------------------------------------------------------------------------- */ + +/* + * Miscellaneous platform dependent initialisations + */ + +int board_init (void) +{ + DECLARE_GLOBAL_DATA_PTR; + + /* memory and cpu-speed are setup before relocation */ + /* so we do _nothing_ here */ + + /* arch number of Sharp Zaurus Corgi : MACH_TYPE_CORGI */ + gd->bd->bi_arch_number = 423; + + /* adress of boot parameters */ + gd->bd->bi_boot_params = 0xa0000100; + + /* set cpu turbo mode */ + set_turbo_mode(); + + corgikbd_init(); + + return 0; +} + +int board_late_init(void) +{ + setenv("stdout", "serial"); + setenv("stderr", "serial"); + return 0; +} + + +int dram_init (void) +{ + DECLARE_GLOBAL_DATA_PTR; + + gd->bd->bi_dram[0].start = PHYS_SDRAM_1; + gd->bd->bi_dram[0].size = PHYS_SDRAM_1_SIZE; + gd->bd->bi_dram[1].start = PHYS_SDRAM_2; + gd->bd->bi_dram[1].size = PHYS_SDRAM_2_SIZE; + gd->bd->bi_dram[2].start = PHYS_SDRAM_3; + gd->bd->bi_dram[2].size = PHYS_SDRAM_3_SIZE; + gd->bd->bi_dram[3].start = PHYS_SDRAM_4; + gd->bd->bi_dram[3].size = PHYS_SDRAM_4_SIZE; + + return 0; +} diff -Nur u-boot-2006-04-18-1106/board/corgi/kbd.c u-boot-2006-04-18-1106-new/board/corgi/kbd.c --- u-boot-2006-04-18-1106/board/corgi/kbd.c 1970-01-01 00:00:00.000000000 +0000 +++ u-boot-2006-04-18-1106-new/board/corgi/kbd.c 2006-07-05 11:19:44.000000000 +0000 @@ -0,0 +1,202 @@ +/* + * board/corgi/kbd.c + * + * Keyboard driver for the Sharp Zaurus SL-C7x0/860. + * + * (C) Copyright 2006 Alexander Chukov + * + * portions from: + * + * linux/drivers/input/keyboard/spitzkbd.c + * + * Keyboard driver for Sharp Corgi models (SL-C7xx) + * + * Copyright (C) 2005 Richard Purdie + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include +#include +#include +#include +#include + +#define GPIO_DFLT_LOW 0x400 +#define GPIO_DFLT_HIGH 0x800 + +void pxa_gpio_mode(int gpio_mode) +{ + int gpio = gpio_mode & GPIO_MD_MASK_NR; + int fn = (gpio_mode & GPIO_MD_MASK_FN) >> 8; + int gafr; + + if (gpio_mode & GPIO_DFLT_LOW) + GPCR(gpio) = GPIO_bit(gpio); + else if (gpio_mode & GPIO_DFLT_HIGH) + GPSR(gpio) = GPIO_bit(gpio); + if (gpio_mode & GPIO_MD_MASK_DIR) + GPDR(gpio) |= GPIO_bit(gpio); + else + GPDR(gpio) &= ~GPIO_bit(gpio); + gafr = GAFR(gpio) & ~(0x3 << (((gpio) & 0xf)*2)); + GAFR(gpio) = gafr | (fn << (((gpio) & 0xf)*2)); +} + +/* + * Corgi Keyboard Definitions + */ +#define CORGI_KEY_STROBE_NUM (12) +#define CORGI_KEY_SENSE_NUM (8) +#define CORGI_GPIO_ALL_STROBE_BIT (0x00003ffc) +#define CORGI_GPIO_HIGH_SENSE_BIT (0xfc000000) +#define CORGI_GPIO_HIGH_SENSE_RSHIFT (26) +#define CORGI_GPIO_LOW_SENSE_BIT (0x00000003) +#define CORGI_GPIO_LOW_SENSE_LSHIFT (6) +#define CORGI_GPIO_STROBE_BIT(a) GPIO_bit(66+(a)) +#define CORGI_GPIO_SENSE_BIT(a) GPIO_bit(58+(a)) +#define CORGI_GAFR_ALL_STROBE_BIT (0x0ffffff0) +#define CORGI_GAFR_HIGH_SENSE_BIT (0xfff00000) +#define CORGI_GAFR_LOW_SENSE_BIT (0x0000000f) +#define CORGI_GPIO_KEY_SENSE(a) (58+(a)) +#define CORGI_GPIO_KEY_STROBE(a) (66+(a)) + +#define CORGI_GPIO_AK_INT (4) /* Headphone Jack Control Interrupt */ + +#define KB_ROWS 8 +#define KB_COLS 12 +#define KB_ROWMASK(r) (1 << (r)) +#define SCANCODE(r,c) ( ((r)<<4) + (c) + 1 ) +/* zero code, 124 scancodes */ +#define NR_SCANCODES ( SCANCODE(KB_ROWS-1,KB_COLS-1) +1 +1 ) + +#define SCAN_INTERVAL (50) /* ms */ +#define HINGE_SCAN_INTERVAL (250) /* ms */ + +#define KB_DISCHARGE_DELAY 10 +#define KB_ACTIVATE_DELAY 10 + +static inline void corgikbd_discharge_all(void) +{ + /* STROBE All HiZ */ + GPCR2 = CORGI_GPIO_ALL_STROBE_BIT; + GPDR2 &= ~CORGI_GPIO_ALL_STROBE_BIT; +} + +static inline void corgikbd_activate_all(void) +{ + /* STROBE ALL -> High */ + GPSR2 = CORGI_GPIO_ALL_STROBE_BIT; + GPDR2 |= CORGI_GPIO_ALL_STROBE_BIT; + + udelay(KB_DISCHARGE_DELAY); + + /* Clear any interrupts we may have triggered when altering the GPIO lines */ + GEDR1 = CORGI_GPIO_HIGH_SENSE_BIT; + GEDR2 = CORGI_GPIO_LOW_SENSE_BIT; +} + +static inline void corgikbd_activate_col(int col) +{ + /* STROBE col -> High, not col -> HiZ */ + GPSR2 = CORGI_GPIO_STROBE_BIT(col); + GPDR2 = (GPDR2 & ~CORGI_GPIO_ALL_STROBE_BIT) | CORGI_GPIO_STROBE_BIT(col); +} + +static inline void corgikbd_reset_col(int col) +{ + /* STROBE col -> Low */ + GPCR2 = CORGI_GPIO_STROBE_BIT(col); + /* STROBE col -> out, not col -> HiZ */ + GPDR2 = (GPDR2 & ~CORGI_GPIO_ALL_STROBE_BIT) | CORGI_GPIO_STROBE_BIT(col); +} + +#define GET_ROWS_STATUS(c) (((GPLR1 & CORGI_GPIO_HIGH_SENSE_BIT) >> CORGI_GPIO_HIGH_SENSE_RSHIFT) | ((GPLR2 & CORGI_GPIO_LOW_SENSE_BIT) << CORGI_GPIO_LOW_SENSE_LSHIFT)) + +static int corgikbd_scankeyboard(void) +{ + unsigned int row, col, rowd; + unsigned int num_pressed; + int ret = -1; + + num_pressed = 0; + for (col = 0; col < KB_COLS; col++) { + corgikbd_discharge_all(); + udelay(KB_DISCHARGE_DELAY); + + corgikbd_activate_col(col); + udelay(KB_ACTIVATE_DELAY); + + rowd = GET_ROWS_STATUS(col); + for (row = 0; row < KB_ROWS; row++) { + unsigned int scancode, pressed; + + scancode = SCANCODE(row, col); + pressed = rowd & KB_ROWMASK(row); + + if (pressed) + ret = scancode; + } + corgikbd_reset_col(col); + } + + corgikbd_activate_all(); + + return ret; +} + +void corgikbd_init(void) +{ + int i; + + /* Setup sense interrupts - RisingEdge Detect, sense lines as inputs */ + for (i = 0; i < CORGI_KEY_SENSE_NUM; i++) + pxa_gpio_mode(CORGI_GPIO_KEY_SENSE(i) | GPIO_IN); + + /* Set Strobe lines as outputs - set high */ + for (i = 0; i < CORGI_KEY_STROBE_NUM; i++) + pxa_gpio_mode(CORGI_GPIO_KEY_STROBE(i) | GPIO_OUT | GPIO_DFLT_HIGH); + + /* Setup the headphone jack as an input */ + pxa_gpio_mode(CORGI_GPIO_AK_INT | GPIO_IN); +} + +int do_testkey(cmd_tbl_t *cmdtp, int flag, int argc, char *argv[]) +{ + int scan; + + if (argc < 2) + return 1; + + scan = corgikbd_scankeyboard(); + + +// if (scan >= 0) +// printf("Scan = %d\n", scan); +// else +// printf("Nothing!\n"); + + return !(simple_strtol(argv[1], NULL, 10) == scan); +} + +U_BOOT_CMD( + testkey, 2, 1, do_testkey, + "testkey - compare pressed key with arg\n", + "" +); diff -Nur u-boot-2006-04-18-1106/board/corgi/lowlevel_init.S u-boot-2006-04-18-1106-new/board/corgi/lowlevel_init.S --- u-boot-2006-04-18-1106/board/corgi/lowlevel_init.S 1970-01-01 00:00:00.000000000 +0000 +++ u-boot-2006-04-18-1106-new/board/corgi/lowlevel_init.S 2006-07-05 11:19:44.000000000 +0000 @@ -0,0 +1,136 @@ +/* + * board/corgi/lowlevel_init.S + * + * Configuration settings for the Sharp Zaurus SL-C7x0/860. + * + * (C) Copyright 2006 Alexander Chukov + * + * This was originally from the Lubbock u-boot port and from BLOB with cleanup + * + * NOTE: I haven't clean this up considerably, just enough to get it + * running. See hal_platform_setup.h for the source. See + * board/cradle/lowlevel_init.S for another PXA250 setup that is + * much cleaner. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include +#include +#include + +/* wait for coprocessor write complete */ + .macro CPWAIT reg + mrc p15,0,\reg,c2,c0,0 + mov \reg,\reg + sub pc,pc,#4 + .endm + +/*********** Write out to HEX 7 segment leds *********/ + +#undef DEBUG_HEXLOG + +#ifdef DEBUG_HEXLOG +#define LEDCTL 0x08000040 +#define LEDDAT1 0x08000010 +#define LEDDAT2 0x08000014 + +.macro wait, count + mov r10, \count +0: + subs r10, r10, #1 + bne 0b +.endm + +.macro hexlog_init + ldr r11, =LEDCTL + mov r10, #0xff + str r10, [r11] + ldr r11, =LEDDAT2 + mov r10, #0xFFFFFFFF + str r10, [r11] + ldr r11, =LEDDAT1 + mov r10, #0x0 + str r10, [r11] +.endm + +.macro hexlog, val + ldr r11, =LEDCTL + mov r10, #0xff + str r10, [r11] + ldr r11, =LEDDAT2 + mov r10, #0xFFFFFFFF + str r10, [r11] + + ldr r11, =LEDDAT1 + mov r10, \val + str r10, [r11] + + wait #0x400000 +.endm + +#else + +.macro hexlog_init + nop +.endm + +.macro hexlog, val + nop +.endm + +#endif + +/***********************************/ + +/* + * Memory setup + */ + +.globl lowlevel_init +lowlevel_init: + + mov pc, lr + +.globl set_turbo_mode + +set_turbo_mode: + /* Turn on turbo mode */ + mrc p14, 0, r2, c6, c0, 0 + orr r2, r2, #0x3 /* Turbo, Freq change */ + mcr p14, 0, r2, c6, c0, 0 + + + /* Setup vectors */ + ldr r0, =TEXT_BASE + ldr r1, =TEXT_BASE+0x40 + ldr r2, =0x0 +1: + ldr r3, [r0] + str r3, [r2] + add r0, r0, #4 + add r2, r2, #4 + cmp r0, r1 + bne 1b + + ldr r0, =0x0 + ldr r1, [r0, #4] + str r1, [r0] + + mov pc, lr diff -Nur u-boot-2006-04-18-1106/board/corgi/nand.c u-boot-2006-04-18-1106-new/board/corgi/nand.c --- u-boot-2006-04-18-1106/board/corgi/nand.c 1970-01-01 00:00:00.000000000 +0000 +++ u-boot-2006-04-18-1106-new/board/corgi/nand.c 2006-07-05 11:19:44.000000000 +0000 @@ -0,0 +1,157 @@ +/* + * board/corgi/nand.c + * + * NAND driver for the Sharp Zaurus SL-C7x0/860. + * + * (C) Copyright 2006 Alexander Chukov + * + * portions from mtd nand driver: + * + * drivers/mtd/nand/sharpsl.c + * + * Copyright (C) 2004 Richard Purdie + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include + + +#if (CONFIG_COMMANDS & CFG_CMD_NAND) + +#include +#include + +static int sharpsl_io_base = CFG_NAND_BASE; + +/* register offset */ +#define ECCLPLB sharpsl_io_base+0x00 /* line parity 7 - 0 bit */ +#define ECCLPUB sharpsl_io_base+0x04 /* line parity 15 - 8 bit */ +#define ECCCP sharpsl_io_base+0x08 /* column parity 5 - 0 bit */ +#define ECCCNTR sharpsl_io_base+0x0C /* ECC byte counter */ +#define ECCCLRR sharpsl_io_base+0x10 /* cleare ECC */ +#define FLASHIO sharpsl_io_base+0x14 /* Flash I/O */ +#define FLASHCTL sharpsl_io_base+0x18 /* Flash Control */ + +/* Flash control bit */ +#define FLRYBY (1 << 5) +#define FLCE1 (1 << 4) +#define FLWP (1 << 3) +#define FLALE (1 << 2) +#define FLCLE (1 << 1) +#define FLCE0 (1 << 0) + +#define readb(address) *((volatile unsigned char *)(address)) +#define writeb(v, address) *((volatile unsigned char *)(address))=v + +/* + * hardware specific access to control-lines + */ +static void +sharpsl_nand_hwcontrol(struct mtd_info* mtd, int cmd) +{ + switch (cmd) { + case NAND_CTL_SETCLE: + writeb(readb(FLASHCTL) | FLCLE, FLASHCTL); + break; + case NAND_CTL_CLRCLE: + writeb(readb(FLASHCTL) & ~FLCLE, FLASHCTL); + break; + + case NAND_CTL_SETALE: + writeb(readb(FLASHCTL) | FLALE, FLASHCTL); + break; + case NAND_CTL_CLRALE: + writeb(readb(FLASHCTL) & ~FLALE, FLASHCTL); + break; + + case NAND_CTL_SETNCE: + writeb(readb(FLASHCTL) & ~(FLCE0|FLCE1), FLASHCTL); + break; + case NAND_CTL_CLRNCE: + writeb(readb(FLASHCTL) | (FLCE0|FLCE1), FLASHCTL); + break; + } +} + +static int +sharpsl_nand_dev_ready(struct mtd_info* mtd) +{ + return !((readb(FLASHCTL) & FLRYBY) == 0); +} + +static void +sharpsl_nand_enable_hwecc(struct mtd_info* mtd, int mode) +{ + writeb(0 ,ECCCLRR); +} + +static int +sharpsl_nand_calculate_ecc(struct mtd_info* mtd, const u_char* dat, + u_char* ecc_code) +{ + ecc_code[0] = ~readb(ECCLPUB); + ecc_code[1] = ~readb(ECCLPLB); + ecc_code[2] = (~readb(ECCCP) << 2) | 0x03; + return readb(ECCCNTR) != 0; +} + +static uint8_t scan_ff_pattern[] = { 0xff, 0xff }; + +static struct nand_bbt_descr sharpsl_bbt = { + .options = 0, + .offs = 4, + .len = 2, + .pattern = scan_ff_pattern +}; + +/* + * Board-specific NAND initialization. The following members of the + * argument are board-specific (per include/linux/mtd/nand.h): + * - IO_ADDR_R?: address to read the 8 I/O lines of the flash device + * - IO_ADDR_W?: address to write the 8 I/O lines of the flash device + * - hwcontrol: hardwarespecific function for accesing control-lines + * - dev_ready: hardwarespecific function for accesing device ready/busy line + * - enable_hwecc?: function to enable (reset) hardware ecc generator. Must + * only be provided if a hardware ECC is available + * - eccmode: mode of ecc, see defines + * - chip_delay: chip dependent delay for transfering data from array to + * read regs (tR) + * - options: various chip options. They can partly be set to inform + * nand_scan about special functionality. See the defines for further + * explanation + * Members with a "?" were not set in the merged testing-NAND branch, + * so they are not set here either. + */ +void board_nand_init(struct nand_chip *nand) +{ + writeb(readb(FLASHCTL) | FLWP, FLASHCTL); + + nand->IO_ADDR_R = FLASHIO; + nand->IO_ADDR_W = FLASHIO; + nand->hwcontrol = sharpsl_nand_hwcontrol; + nand->dev_ready = sharpsl_nand_dev_ready; + nand->eccmode = NAND_ECC_HW3_256; + nand->chip_delay = 15; + nand->badblock_pattern = &sharpsl_bbt; + nand->enable_hwecc = sharpsl_nand_enable_hwecc; + nand->calculate_ecc = sharpsl_nand_calculate_ecc; + nand->correct_data = nand_correct_data; +} +#endif /* (CONFIG_COMMANDS & CFG_CMD_NAND) */ diff -Nur u-boot-2006-04-18-1106/board/corgi/u-boot.lds u-boot-2006-04-18-1106-new/board/corgi/u-boot.lds --- u-boot-2006-04-18-1106/board/corgi/u-boot.lds 1970-01-01 00:00:00.000000000 +0000 +++ u-boot-2006-04-18-1106-new/board/corgi/u-boot.lds 2006-07-05 11:19:44.000000000 +0000 @@ -0,0 +1,56 @@ +/* + * (C) Copyright 2000 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +OUTPUT_FORMAT("elf32-littlearm", "elf32-littlearm", "elf32-littlearm") +OUTPUT_ARCH(arm) +ENTRY(_start) +SECTIONS +{ + . = 0x00000000; + + . = ALIGN(4); + .text : + { + cpu/pxa/start.o (.text) + *(.text) + } + + . = ALIGN(4); + .rodata : { *(.rodata) } + + . = ALIGN(4); + .data : { *(.data) } + + . = ALIGN(4); + .got : { *(.got) } + + . = .; + __u_boot_cmd_start = .; + .u_boot_cmd : { *(.u_boot_cmd) } + __u_boot_cmd_end = .; + + . = ALIGN(4); + __bss_start = .; + .bss : { *(.bss) } + _end = .; +} diff -Nur u-boot-2006-04-18-1106/common/cmd_nand.c u-boot-2006-04-18-1106-new/common/cmd_nand.c --- u-boot-2006-04-18-1106/common/cmd_nand.c 2006-04-18 09:05:03.000000000 +0000 +++ u-boot-2006-04-18-1106-new/common/cmd_nand.c 2006-07-05 11:19:44.000000000 +0000 @@ -81,6 +81,63 @@ return 0; } +#ifdef NAND_LOGICAL +///////////////////////////////////////////////////////////////////// +// oob structure +///////////////////////////////////////////////////////////////////// + +#define NAND_NOOB_LOGADDR_00 8 +#define NAND_NOOB_LOGADDR_01 9 +#define NAND_NOOB_LOGADDR_10 10 +#define NAND_NOOB_LOGADDR_11 11 +#define NAND_NOOB_LOGADDR_20 12 +#define NAND_NOOB_LOGADDR_21 13 + +static uint nand_get_logical_no(unsigned char *oob) +{ + unsigned short us,bit; + int par; + int good0, good1; + + if(oob[NAND_NOOB_LOGADDR_00] == oob[NAND_NOOB_LOGADDR_10] && + oob[NAND_NOOB_LOGADDR_01] == oob[NAND_NOOB_LOGADDR_11]){ + good0 = NAND_NOOB_LOGADDR_00; + good1 = NAND_NOOB_LOGADDR_01; + }else + if(oob[NAND_NOOB_LOGADDR_10] == oob[NAND_NOOB_LOGADDR_20] && + oob[NAND_NOOB_LOGADDR_11] == oob[NAND_NOOB_LOGADDR_21]){ + good0 = NAND_NOOB_LOGADDR_10; + good1 = NAND_NOOB_LOGADDR_11; + }else + if(oob[NAND_NOOB_LOGADDR_20] == oob[NAND_NOOB_LOGADDR_00] && + oob[NAND_NOOB_LOGADDR_21] == oob[NAND_NOOB_LOGADDR_01]){ + good0 = NAND_NOOB_LOGADDR_20; + good1 = NAND_NOOB_LOGADDR_21; + }else{ + return (uint)-1; + } + + us = (((unsigned short)(oob[good0]) & 0x00ff) << 0) | + (((unsigned short)(oob[good1]) & 0x00ff) << 8); + + par = 0; + for(bit = 0x0001; bit != 0; bit <<= 1){ + if(us & bit){ + par++; + } + } + if(par & 1){ + return (uint)-2; + } + + if(us == 0xffff){ + return 0xffff; + }else{ + return ((us & 0x07fe) >> 1); + } +} +#endif + /* ------------------------------------------------------------------------- */ static void @@ -245,6 +302,55 @@ if (off == 0 && size == 0) return 1; +#ifdef NAND_LOGICAL + s = strchr(cmd, '.'); + if (s != NULL) { + if (strcmp(s, ".logical") == 0) { + int blocks = NAND_LOGICAL_SIZE / nand->erasesize; + ulong *log2phy = malloc(blocks * sizeof(ulong)); + u_char *oobuf = malloc(nand->oobblock + nand->oobsize); + int i; + ulong offset; + ret = 1; + for (i = 0; i < blocks; i++) + log2phy[i] = (uint) -1; + offset = 0; + for (i = 0; i < blocks; i++) { + ret = nand_read_raw(nand, oobuf, offset, nand->oobblock, nand->oobsize); + if (!ret) { + int log_no = nand_get_logical_no(oobuf + nand->oobblock); + if (((int)log_no >= 0) && (log_no < blocks)) { + log2phy[log_no] = offset; + //printf("NAND logical - %08X -> %04X\n", offset, log_no); + } + } + offset += nand->erasesize; + } + + for (i = 0; i < size / nand->erasesize; i++) { + ulong sz = nand->erasesize; + offset = log2phy[off / nand->erasesize]; + if ((int)offset < 0) { + printf("NAND logical - offset %08X not found\n", off); + return 1; + } + //printf("NAND logical - %04X -> %08X\n", off / nand->erasesize, offset); + ret = nand_read(nand, offset, &sz, (u_char *)addr); + if (ret) { + printf("NAND logical - offset %08X, read error\n", off); + return 1; + } + off += nand->erasesize; + addr += nand->erasesize; + } + printf(" %d bytes read from NAND logical\n", size); + free(oobuf); + free(log2phy); + return ret == 0 ? 0 : 1; + } + } +#endif + i = strncmp(cmd, "read", 4) == 0; /* 1 = read, 0 = write */ printf("\nNAND %s: device %d offset %u, size %u ... ", i ? "read" : "write", nand_curr_device, off, size); diff -Nur u-boot-2006-04-18-1106/cpu/pxa/config.mk u-boot-2006-04-18-1106-new/cpu/pxa/config.mk --- u-boot-2006-04-18-1106/cpu/pxa/config.mk 2006-04-18 09:05:03.000000000 +0000 +++ u-boot-2006-04-18-1106-new/cpu/pxa/config.mk 2006-07-05 11:19:44.000000000 +0000 @@ -22,8 +22,7 @@ # MA 02111-1307 USA # -PLATFORM_RELFLAGS += -fno-strict-aliasing -fno-common -ffixed-r8 \ - -msoft-float +PLATFORM_RELFLAGS += -fno-strict-aliasing -fno-common -ffixed-r8 -fomit-frame-pointer #PLATFORM_CPPFLAGS += -mapcs-32 -march=armv4 -mtune=strongarm1100 PLATFORM_CPPFLAGS += -march=armv5 -mtune=xscale @@ -32,5 +31,5 @@ # Supply options according to compiler version # # ======================================================================== -PLATFORM_CPPFLAGS +=$(call cc-option,-mapcs-32,-mabi=apcs-gnu) +#PLATFORM_CPPFLAGS +=$(call cc-option,-mapcs-32,-mabi=apcs-gnu) PLATFORM_RELFLAGS +=$(call cc-option,-mshort-load-bytes,$(call cc-option,-malignment-traps,)) diff -Nur u-boot-2006-04-18-1106/cpu/pxa/start.S u-boot-2006-04-18-1106-new/cpu/pxa/start.S --- u-boot-2006-04-18-1106/cpu/pxa/start.S 2006-04-18 09:05:03.000000000 +0000 +++ u-boot-2006-04-18-1106-new/cpu/pxa/start.S 2006-07-05 11:19:44.000000000 +0000 @@ -42,6 +42,7 @@ ldr pc, _irq ldr pc, _fiq +_reset: .word reset _undefined_instruction: .word undefined_instruction _software_interrupt: .word software_interrupt _prefetch_abort: .word prefetch_abort diff -Nur u-boot-2006-04-18-1106/fs/cramfs/cramfs.c u-boot-2006-04-18-1106-new/fs/cramfs/cramfs.c --- u-boot-2006-04-18-1106/fs/cramfs/cramfs.c 2006-04-18 09:05:03.000000000 +0000 +++ u-boot-2006-04-18-1106-new/fs/cramfs/cramfs.c 2006-07-05 11:19:44.000000000 +0000 @@ -44,8 +44,13 @@ /* CPU address space offset calculation macro, struct part_info offset is * device address space offset, so we need to shift it by a device start address. */ +#if (CONFIG_COMMANDS & CFG_CMD_FLASH) extern flash_info_t flash_info[]; #define PART_OFFSET(x) (x->offset + flash_info[x->dev->id->num].start[0]) +#else +static struct cramfs_super super_fake; +#define PART_OFFSET(x) (&super_fake) +#endif static int cramfs_read_super (struct part_info *info) { diff -Nur u-boot-2006-04-18-1106/include/asm-arm/arch-pxa/pxa-regs.h u-boot-2006-04-18-1106-new/include/asm-arm/arch-pxa/pxa-regs.h --- u-boot-2006-04-18-1106/include/asm-arm/arch-pxa/pxa-regs.h 2006-04-18 09:05:03.000000000 +0000 +++ u-boot-2006-04-18-1106-new/include/asm-arm/arch-pxa/pxa-regs.h 2006-07-05 11:19:44.000000000 +0000 @@ -1269,15 +1269,16 @@ #define _GEDR(x) __REG2(0x40E00048, ((x) & 0x60) >> 3) #define _GAFR(x) __REG2(0x40E00054, ((x) & 0x70) >> 2) -#define GPLR(x) ((((x) & 0x7f) < 96) ? _GPLR(x) : GPLR3) -#define GPDR(x) ((((x) & 0x7f) < 96) ? _GPDR(x) : GPDR3) -#define GPSR(x) ((((x) & 0x7f) < 96) ? _GPSR(x) : GPSR3) -#define GPCR(x) ((((x) & 0x7f) < 96) ? _GPCR(x) : GPCR3) -#define GRER(x) ((((x) & 0x7f) < 96) ? _GRER(x) : GRER3) -#define GFER(x) ((((x) & 0x7f) < 96) ? _GFER(x) : GFER3) -#define GEDR(x) ((((x) & 0x7f) < 96) ? _GEDR(x) : GEDR3) -#define GAFR(x) ((((x) & 0x7f) < 96) ? _GAFR(x) : \ - ((((x) & 0x7f) < 112) ? GAFR3_L : GAFR3_U)) +#define GPLR(x) (*((((x) & 0x7f) < 96) ? &_GPLR(x) : &GPLR3)) +#define GPDR(x) (*((((x) & 0x7f) < 96) ? &_GPDR(x) : &GPDR3)) +#define GPSR(x) (*((((x) & 0x7f) < 96) ? &_GPSR(x) : &GPSR3)) +#define GPCR(x) (*((((x) & 0x7f) < 96) ? &_GPCR(x) : &GPCR3)) +#define GRER(x) (*((((x) & 0x7f) < 96) ? &_GRER(x) : &GRER3)) +#define GFER(x) (*((((x) & 0x7f) < 96) ? &_GFER(x) : &GFER3)) +#define GEDR(x) (*((((x) & 0x7f) < 96) ? &_GEDR(x) : &GEDR3)) +#define GAFR(x) (*((((x) & 0x7f) < 96) ? &_GAFR(x) : \ + ((((x) & 0x7f) < 112) ? &GAFR3_L : &GAFR3_U))) + #else #define GPLR(x) __REG2(0x40E00000, ((x) & 0x60) >> 3) diff -Nur u-boot-2006-04-18-1106/include/configs/akita.h u-boot-2006-04-18-1106-new/include/configs/akita.h --- u-boot-2006-04-18-1106/include/configs/akita.h 1970-01-01 00:00:00.000000000 +0000 +++ u-boot-2006-04-18-1106-new/include/configs/akita.h 2006-07-13 11:00:46.000000000 +0000 @@ -0,0 +1,324 @@ +/* + * include/configs/akita.h + * + * Configuration settings for the Sharp Zaurus SL-C1000/C3100. + * + * (C) Copyright 2006 Alexander Chukov + * + * portions from adsvix board configuration: + * (C) Copyright 2004 + * Robert Whaley, Applied Data Systems, Inc. rwhaley@applieddata.net + * (C) Copyright 2002 + * Kyle Harris, Nexus Technologies, Inc. kharris@nexus-tech.net + * (C) Copyright 2002 + * Sysgo Real-Time Solutions, GmbH + * Marius Groeger + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +#define CONFIG_SKIP_LOWLEVEL_INIT + +#undef SKIP_CONFIG_RELOCATE_UBOOT + +#undef CONFIG_HARD_I2C + +/* + * High Level Configuration Options + * (easy to change) + */ +#define CONFIG_PXA27X 1 /* This is an PXA27x CPU */ +#define CONFIG_AKITA 1 /* on Sharp Zaurus Akita */ +//#define CONFIG_MMC 1 +#define BOARD_LATE_INIT 1 + +#undef CONFIG_USE_IRQ /* we don't need IRQ/FIQ stuff */ + +#define RTC 1 + +/* + * Size of malloc() pool + */ +//#define CFG_MALLOC_LEN (CFG_ENV_SIZE + 128*1024) +#define CFG_MALLOC_LEN (CFG_ENV_SIZE + 256*1024) +#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */ + +/* + * select serial console configuration + */ +#define CONFIG_FFUART 1 /* we use FFUART on Mainstone */ + +/* allow to overwrite serial and ethaddr */ +#define CONFIG_BAUDRATE 115200 +//#define CONFIG_DOS_PARTITION 1 + +#undef CONFIG_SHOW_BOOT_PROGRESS + +#if 1 +#define CONFIG_BOOTDELAY 1 +#define CONFIG_AUTOBOOT_PROMPT "Autobooting in %d seconds\n" + +#define CONFIG_BOOTCOMMAND \ + "if testkey 101 ; " \ + "then " \ + "nand read.logical 0xa1000000 0x00060000 0x00540000; " \ + "setenv bootargs console=ttyS0,115200 console=tty1 root=/dev/ram rw fbcon=rotate:1 ramdisk_size=8192; " \ + "bootm; " \ + "fi; " \ + "if testkey 2 ; " \ + "then " \ + "nand read.logical 0xa1000000 0x005a0000 0x00160000; " \ + "setenv bootargs console=ttyS0,115200 console=tty1 root=/dev/mmcblk0p1 fbcon=rotate:1; " \ + "bootm; " \ + "fi; " \ + "if testkey 18 ; " \ + "then " \ + "nand read.logical 0xa1000000 0x005a0000 0x00160000; " \ + "setenv bootargs console=ttyS0,115200 console=tty1 root=/dev/hda1 fbcon=rotate:1; " \ + "bootm; " \ + "fi; " \ + "if testkey 3 ; " \ + "then " \ + "nand read.logical 0xa1000000 0x005a0000 0x00160000; " \ + "setenv bootargs console=ttyS0,115200 console=tty1 root=/dev/hdc1 fbcon=rotate:1; " \ + "bootm; " \ + "fi; " \ + "nand read.logical 0xa1000000 0x005a0000 0x00160000; " \ + "setenv bootargs console=ttyS0,115200 console=tty1 root=/dev/mtdblock2 rootfstype=jffs2 fbcon=rotate:1; " \ + "bootm; " +#else +#define CONFIG_BOOTCOMMAND "" // "run boot_flash" +#endif + +#define CONFIG_BOOTARGS "console=ttyS0,115200 console=tty1 root=/dev/ram rw fbcon=rotate:1 ramdisk_size=8192" +#define CONFIG_SETUP_MEMORY_TAGS 1 +#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */ +#define CONFIG_INITRD_TAG 1 + +#define CONFIG_COMMANDS (( \ + CONFIG_CMD_DFL | \ + CFG_CMD_NAND | \ + CFG_CMD_JFFS2 \ + ) & ~( \ + CFG_CMD_NET | \ + CFG_CMD_FLASH | \ + CFG_CMD_IMLS \ + )) + +// CFG_CMD_ENV + +/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */ +#include + + +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ +#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ +#endif + +/* + * Miscellaneous configurable options + */ +#define CFG_HUSH_PARSER 1 +#define CFG_PROMPT_HUSH_PS2 "> " + +#define CFG_LONGHELP /* undef to save memory */ +#define CFG_PROMPT "U-Boot> " /* Monitor Command Prompt */ + +#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ +#define CFG_MAXARGS 16 /* max number of command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ +#define CFG_DEVICE_NULLDEV 1 + +#define CFG_MEMTEST_START 0xa0400000 /* memtest works on */ +#define CFG_MEMTEST_END 0xa0800000 /* 4 ... 8 MB in DRAM */ + +#undef CFG_CLKS_IN_HZ /* everything, incl board info, in Hz */ + +#define CFG_LOAD_ADDR 0xa1000000 /* default load address */ + +#define CFG_HZ 3686400 /* incrementer freq: 3.6864 MHz */ +#define CFG_CPUSPEED 0x207 /* need to look more closely, I think this is Turbo = 2x, L=91Mhz */ + + /* valid baudrates */ +#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } + +#define CFG_MMC_BASE 0xF0000000 + +/* + * Stack sizes + * + * The stack sizes are set up in start.S using the settings below + */ +#define CONFIG_STACKSIZE (128*1024) /* regular stack */ +#ifdef CONFIG_USE_IRQ +#define CONFIG_STACKSIZE_IRQ (4*1024) /* IRQ stack */ +#define CONFIG_STACKSIZE_FIQ (4*1024) /* FIQ stack */ +#endif + +/* + * Physical Memory Map + */ +#define CONFIG_NR_DRAM_BANKS 4 /* we have 2 banks of DRAM */ +#define PHYS_SDRAM_1 0xa0000000 /* SDRAM Bank #1 */ +#define PHYS_SDRAM_1_SIZE 0x04000000 /* 64 MB */ +#define PHYS_SDRAM_2 0xa4000000 /* SDRAM Bank #2 */ +#define PHYS_SDRAM_2_SIZE 0x00000000 /* 0 MB */ +#define PHYS_SDRAM_3 0xa8000000 /* SDRAM Bank #3 */ +#define PHYS_SDRAM_3_SIZE 0x00000000 /* 0 MB */ +#define PHYS_SDRAM_4 0xac000000 /* SDRAM Bank #4 */ +#define PHYS_SDRAM_4_SIZE 0x00000000 /* 0 MB */ + +#define PHYS_FLASH_1 0xd4000000 /* Flash Bank #1 */ + +#define CFG_DRAM_BASE 0xa0000000 +#define CFG_DRAM_SIZE 0x04000000 + +#define CFG_FLASH_BASE PHYS_FLASH_1 + +/* + * GPIO settings for Mainstone + */ + +#define CFG_GPSR0_VAL 0x00708800 +#define CFG_GPSR1_VAL 0x03cf0002 +#define CFG_GPSR2_VAL 0x0021FC00 +#define CFG_GPSR3_VAL 0x00000000 + +#define CFG_GPCR0_VAL 0x00001000 +#define CFG_GPCR1_VAL 0x00000000 +#define CFG_GPCR2_VAL 0x00000000 +#define CFG_GPCR3_VAL 0x00000000 + +#define CFG_GPDR0_VAL 0xC27B9C04 +#define CFG_GPDR1_VAL 0x00EFAA83 +#define CFG_GPDR2_VAL 0x0E23FC00 +#define CFG_GPDR3_VAL 0x001E1F81 + +#define CFG_GAFR0_L_VAL 0x94F00000 +#define CFG_GAFR0_U_VAL 0x015A859A +#define CFG_GAFR1_L_VAL 0x999A955A +#define CFG_GAFR1_U_VAL 0x0005A4AA +#define CFG_GAFR2_L_VAL 0x6AA00000 +#define CFG_GAFR2_U_VAL 0x55A8041A +#define CFG_GAFR3_L_VAL 0x56AA955A +#define CFG_GAFR3_U_VAL 0x00000001 + +#define CFG_PSSR_VAL 0x20 // ??????????? + +/* + * PCMCIA and CF Interfaces + */ +#define CFG_MECR_VAL 0x00000001 +#define CFG_MCMEM0_VAL 0x00010204 +#define CFG_MCMEM1_VAL 0x00010204 +#define CFG_MCATT0_VAL 0x00010204 +#define CFG_MCATT1_VAL 0x00010204 +#define CFG_MCIO0_VAL 0x0000c108 +#define CFG_MCIO1_VAL 0x0001c108 + +//#define CONFIG_PXA_PCMCIA 1 +//#define CONFIG_PXA_IDE 1 + +#define CONFIG_PCMCIA_SLOT_A 1 +/* just to keep build system happy */ + +#define CFG_PCMCIA_MEM_ADDR 0x28000000 +#define CFG_PCMCIA_MEM_SIZE 0x04000000 + +#define CFG_IDE_MAXBUS 1 +/* max. 1 IDE bus */ +#define CFG_IDE_MAXDEVICE 1 +/* max. 1 drive per IDE bus */ + +#define CFG_ATA_IDE0_OFFSET 0x0000 + +#define CFG_ATA_BASE_ADDR 0x20000000 + +/* Offset for data I/O */ +#define CFG_ATA_DATA_OFFSET 0x1f0 + +/* Offset for normal register accesses */ +#define CFG_ATA_REG_OFFSET 0x1f0 + +/* Offset for alternate registers */ +#define CFG_ATA_ALT_OFFSET 0x3f0 + +#define CFG_NO_FLASH 1 +#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */ +#define CFG_MAX_FLASH_SECT 512 /* max number of sectors on one chip */ + +/*----------------------------------------------------------------------- + * NAND-FLASH stuff + *----------------------------------------------------------------------- + */ +#undef CFG_NAND_LEGACY + +/* NAND debugging */ +//#define CONFIG_MTD_DEBUG +//#define CONFIG_MTD_DEBUG_VERBOSE 3 + +#define CFG_NAND_BASE 0xd4000000 +#define CFG_MAX_NAND_DEVICE 1 /* Max number of NAND devices */ +#define NAND_MAX_CHIPS 1 + +//#define CONFIG_MTD_NAND_VERIFY_WRITE 1 /* verify all writes!!! */ +//#define CFG_NAND_SKIP_BAD_DOT_I 1 /* ".i" read skips bad blocks */ + +#define CONFIG_JFFS2_NAND 1 /* jffs2 on nand support */ +#define NAND_CACHE_PAGES 16 /* size of nand cache in 512 bytes pages */ + +/* + * JFFS2 partitions + * + */ +/* No command line, one static partition */ +//#undef CONFIG_JFFS2_CMDLINE +//#define CONFIG_JFFS2_DEV "nand0" +//#define CONFIG_JFFS2_PART_SIZE 0xFFFFFFFF +//#define CONFIG_JFFS2_PART_OFFSET 0x00060000 + +/* mtdparts command line support */ +/* Note: fake mtd_id used, no linux mtd map file */ + +#define CONFIG_JFFS2_CMDLINE +#define MTDIDS_DEFAULT "nand0=laze-0" +//#define MTDPARTS_DEFAULT "mtdparts=laze-0:256k(uboot),128k(env),-(jffs2)" +#define MTDPARTS_DEFAULT "mtdparts=laze-0:7168k(Logical),-(JFFS2)" + +/* + * SHARP SL NAND logical partition + */ +#define NAND_LOGICAL 1 +#define NAND_LOGICAL_SIZE 0x700000 + +/* + * Environment + */ + +#define CFG_ENV_IS_IN_NAND 1 +#define CFG_ENV_OFFSET 0x40000 +//#define CFG_ENV_OFFSET_REDUND 0x44000 +#define CFG_ENV_SIZE 0x20000 + +#endif /* __CONFIG_H */ diff -Nur u-boot-2006-04-18-1106/include/configs/corgi.h u-boot-2006-04-18-1106-new/include/configs/corgi.h --- u-boot-2006-04-18-1106/include/configs/corgi.h 1970-01-01 00:00:00.000000000 +0000 +++ u-boot-2006-04-18-1106-new/include/configs/corgi.h 2006-07-13 11:19:04.000000000 +0000 @@ -0,0 +1,326 @@ +/* + * include/configs/corgi.h + * + * Configuration settings for the Sharp Zaurus SL-C7x0/C860. + * + * (C) Copyright 2006 Alexander Chukov + * + * portions from adsvix board configuration: + * (C) Copyright 2004 + * Robert Whaley, Applied Data Systems, Inc. rwhaley@applieddata.net + * (C) Copyright 2002 + * Kyle Harris, Nexus Technologies, Inc. kharris@nexus-tech.net + * (C) Copyright 2002 + * Sysgo Real-Time Solutions, GmbH + * Marius Groeger + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +#define CONFIG_SKIP_LOWLEVEL_INIT + +#undef SKIP_CONFIG_RELOCATE_UBOOT + +#undef CONFIG_HARD_I2C + +/* + * High Level Configuration Options + * (easy to change) + */ +#define CONFIG_PXA250 1 /* This is an PXA255 CPU */ +#define CONFIG_CORGI 1 /* on Sharp Zaurus Corgi */ +//#define CONFIG_MMC 1 +#define BOARD_LATE_INIT 1 + +#undef CONFIG_USE_IRQ /* we don't need IRQ/FIQ stuff */ + +#define RTC 1 + +/* + * Size of malloc() pool + */ +//#define CFG_MALLOC_LEN (CFG_ENV_SIZE + 128*1024) +#define CFG_MALLOC_LEN (CFG_ENV_SIZE + 256*1024) +#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */ + +/* + * select serial console configuration + */ +#define CONFIG_FFUART 1 /* we use FFUART on Mainstone */ + +/* allow to overwrite serial and ethaddr */ +#define CONFIG_BAUDRATE 115200 +//#define CONFIG_DOS_PARTITION 1 + +#undef CONFIG_SHOW_BOOT_PROGRESS + +#if 1 +#define CONFIG_BOOTDELAY 1 +#define CONFIG_AUTOBOOT_PROMPT "Autobooting in %d seconds\n" + +#define CONFIG_BOOTCOMMAND \ + "if testkey 101 ; " \ + "then " \ + "nand read.logical 0xa0800000 0x00060000 0x00540000; " \ + "setenv bootargs console=ttyS0,115200 console=tty1 root=/dev/ram rw ramdisk_size=8192; " \ + "bootm; " \ + "fi; " \ + "if testkey 2 ; " \ + "then " \ + "nand read.logical 0xa0800000 0x005a0000 0x00160000; " \ + "setenv bootargs console=ttyS0,115200 console=tty1 root=/dev/mmcblk0p1; " \ + "bootm; " \ + "fi; " \ + "if testkey 18 ; " \ + "then " \ + "nand read.logical 0xa0800000 0x005a0000 0x00160000; " \ + "setenv bootargs console=ttyS0,115200 console=tty1 root=/dev/hda1; " \ + "bootm; " \ + "fi; " \ + "if testkey 3 ; " \ + "then " \ + "nand read.logical 0xa0800000 0x005a0000 0x00160000; " \ + "setenv bootargs console=ttyS0,115200 console=tty1 root=/dev/hdc1; " \ + "bootm; " \ + "fi; " \ + "nand read.logical 0xa0800000 0x005a0000 0x00160000; " \ + "setenv bootargs console=ttyS0,115200 console=tty1 root=/dev/mtdblock2 rootfstype=jffs2; " \ + "bootm; " +#else +#define CONFIG_BOOTCOMMAND "" // "run boot_flash" +#endif + +#define CONFIG_BOOTARGS "console=ttyS0,115200 console=tty1 root=/dev/ram rw ramdisk_size=8192" +#define CONFIG_SETUP_MEMORY_TAGS 1 +#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */ +#define CONFIG_INITRD_TAG 1 + +#define CONFIG_COMMANDS (( \ + CONFIG_CMD_DFL | \ + CFG_CMD_NAND | \ + CFG_CMD_JFFS2 \ + ) & ~( \ + CFG_CMD_NET | \ + CFG_CMD_FLASH | \ + CFG_CMD_IMLS \ + )) + +// CFG_CMD_ENV + +/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */ +#include + + +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ +#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ +#endif + +/* + * Miscellaneous configurable options + */ +#define CFG_HUSH_PARSER 1 +#define CFG_PROMPT_HUSH_PS2 "> " + +#define CFG_LONGHELP /* undef to save memory */ +#define CFG_PROMPT "U-Boot> " /* Monitor Command Prompt */ + +#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ +#define CFG_MAXARGS 16 /* max number of command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ +#define CFG_DEVICE_NULLDEV 1 + +#define CFG_MEMTEST_START 0xa0400000 /* memtest works on */ +#define CFG_MEMTEST_END 0xa0800000 /* 4 ... 8 MB in DRAM */ + +#undef CFG_CLKS_IN_HZ /* everything, incl board info, in Hz */ + +#define CFG_LOAD_ADDR 0xa0800000 /* default load address */ + +#define CFG_HZ 3686400 /* incrementer freq: 3.6864 MHz */ +#define CFG_CPUSPEED 0x207 /* need to look more closely, I think this is Turbo = 2x, L=91Mhz */ + + /* valid baudrates */ +#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } + +#define CFG_MMC_BASE 0xF0000000 + +/* + * Stack sizes + * + * The stack sizes are set up in start.S using the settings below + */ +#define CONFIG_STACKSIZE (128*1024) /* regular stack */ +#ifdef CONFIG_USE_IRQ +#define CONFIG_STACKSIZE_IRQ (4*1024) /* IRQ stack */ +#define CONFIG_STACKSIZE_FIQ (4*1024) /* FIQ stack */ +#endif + +/* + * Physical Memory Map + */ +#define CONFIG_NR_DRAM_BANKS 4 /* we have 2 banks of DRAM */ +#define PHYS_SDRAM_1 0xa0000000 /* SDRAM Bank #1 */ +#define PHYS_SDRAM_1_SIZE 0x04000000 /* 64 MB */ +#define PHYS_SDRAM_2 0xa4000000 /* SDRAM Bank #2 */ +#define PHYS_SDRAM_2_SIZE 0x00000000 /* 0 MB */ +#define PHYS_SDRAM_3 0xa8000000 /* SDRAM Bank #3 */ +#define PHYS_SDRAM_3_SIZE 0x00000000 /* 0 MB */ +#define PHYS_SDRAM_4 0xac000000 /* SDRAM Bank #4 */ +#define PHYS_SDRAM_4_SIZE 0x00000000 /* 0 MB */ + +#define PHYS_FLASH_1 0xd4000000 /* Flash Bank #1 */ + +#define CFG_DRAM_BASE 0xa0000000 +#define CFG_DRAM_SIZE 0x04000000 + +#define CFG_FLASH_BASE PHYS_FLASH_1 + +/* + * GPIO settings for Mainstone + */ + +#define CFG_GPSR0_VAL 0x00708800 +#define CFG_GPSR1_VAL 0x03cf0002 +#define CFG_GPSR2_VAL 0x0021FC00 +#define CFG_GPSR3_VAL 0x00000000 + +#define CFG_GPCR0_VAL 0x00001000 +#define CFG_GPCR1_VAL 0x00000000 +#define CFG_GPCR2_VAL 0x00000000 +#define CFG_GPCR3_VAL 0x00000000 + +#define CFG_GPDR0_VAL 0xC27B9C04 +#define CFG_GPDR1_VAL 0x00EFAA83 +#define CFG_GPDR2_VAL 0x0E23FC00 +#define CFG_GPDR3_VAL 0x001E1F81 + +#define CFG_GAFR0_L_VAL 0x94F00000 +#define CFG_GAFR0_U_VAL 0x015A859A +#define CFG_GAFR1_L_VAL 0x999A955A +#define CFG_GAFR1_U_VAL 0x0005A4AA +#define CFG_GAFR2_L_VAL 0x6AA00000 +#define CFG_GAFR2_U_VAL 0x55A8041A +#define CFG_GAFR3_L_VAL 0x56AA955A +#define CFG_GAFR3_U_VAL 0x00000001 + +#define CFG_PSSR_VAL 0x20 // ??????????? + +/* + * PCMCIA and CF Interfaces + */ +#define CFG_MECR_VAL 0x00000001 +#define CFG_MCMEM0_VAL 0x00010204 +#define CFG_MCMEM1_VAL 0x00010204 +#define CFG_MCATT0_VAL 0x00010204 +#define CFG_MCATT1_VAL 0x00010204 +#define CFG_MCIO0_VAL 0x0000c108 +#define CFG_MCIO1_VAL 0x0001c108 + +//#define CONFIG_PXA_PCMCIA 1 +//#define CONFIG_PXA_IDE 1 + +#define CONFIG_PCMCIA_SLOT_A 1 +/* just to keep build system happy */ + +#define CFG_PCMCIA_MEM_ADDR 0x28000000 +#define CFG_PCMCIA_MEM_SIZE 0x04000000 + +#define CFG_IDE_MAXBUS 1 +/* max. 1 IDE bus */ +#define CFG_IDE_MAXDEVICE 1 +/* max. 1 drive per IDE bus */ + +#define CFG_ATA_IDE0_OFFSET 0x0000 + +#define CFG_ATA_BASE_ADDR 0x20000000 + +/* Offset for data I/O */ +#define CFG_ATA_DATA_OFFSET 0x1f0 + +/* Offset for normal register accesses */ +#define CFG_ATA_REG_OFFSET 0x1f0 + +/* Offset for alternate registers */ +#define CFG_ATA_ALT_OFFSET 0x3f0 + +#define CFG_NO_FLASH 1 +#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */ +#define CFG_MAX_FLASH_SECT 512 /* max number of sectors on one chip */ + +/*----------------------------------------------------------------------- + * NAND-FLASH stuff + *----------------------------------------------------------------------- + */ +#undef CFG_NAND_LEGACY + +/* NAND debugging */ +//#define CONFIG_MTD_DEBUG +//#define CONFIG_MTD_DEBUG_VERBOSE 3 + +#define CFG_NAND_BASE 0xd4000000 +#define CFG_MAX_NAND_DEVICE 1 /* Max number of NAND devices */ +#define NAND_MAX_CHIPS 1 + +//#define CONFIG_MTD_NAND_VERIFY_WRITE 1 /* verify all writes!!! */ +//#define CFG_NAND_SKIP_BAD_DOT_I 1 /* ".i" read skips bad blocks */ + +#define CONFIG_JFFS2_NAND 1 /* jffs2 on nand support */ +#define NAND_CACHE_PAGES 16 /* size of nand cache in 512 bytes pages */ + +#define NAND_ALLOW_ERASE_ALL 1 + +/* + * JFFS2 partitions + * + */ +/* No command line, one static partition */ +//#undef CONFIG_JFFS2_CMDLINE +//#define CONFIG_JFFS2_DEV "nand0" +//#define CONFIG_JFFS2_PART_SIZE 0xFFFFFFFF +//#define CONFIG_JFFS2_PART_OFFSET 0x00060000 + +/* mtdparts command line support */ +/* Note: fake mtd_id used, no linux mtd map file */ + +#define CONFIG_JFFS2_CMDLINE +#define MTDIDS_DEFAULT "nand0=laze-0" +//#define MTDPARTS_DEFAULT "mtdparts=laze-0:256k(uboot),128k(env),-(jffs2)" +#define MTDPARTS_DEFAULT "mtdparts=laze-0:7168k(Logical),-(JFFS2)" + +/* + * SHARP SL NAND logical partition + */ +#define NAND_LOGICAL 1 +#define NAND_LOGICAL_SIZE 0x700000 + +/* + * Environment + */ + +#define CFG_ENV_IS_IN_NAND 1 +#define CFG_ENV_OFFSET 0x40000 +//#define CFG_ENV_OFFSET_REDUND 0x44000 +#define CFG_ENV_SIZE 0x20000 + +#endif /* __CONFIG_H */ --- s/examples/Makefile.orig 2006-12-09 15:08:45.000000000 +0600 +++ s/examples/Makefile 2006-12-09 15:09:00.000000000 +0600 @@ -60,7 +60,7 @@ include $(TOPDIR)/config.mk SREC = hello_world.srec -BIN = hello_world.bin hello_world +BIN = hello_world hello_world.bin ifeq ($(CPU),mpc8xx) SREC = test_burst.srec @@ -122,7 +122,7 @@ CPPFLAGS += -I.. -all: .depend $(OBJS) $(LIB) $(SREC) $(BIN) +all: .depend $(OBJS) $(LIB) $(BIN) $(SREC) ######################################################################### $(LIB): .depend $(LIBOBJS)