Index: u-boot-1.3.2/board/freescale/mpc8313erdb/mpc8313erdb.c
===================================================================
--- u-boot-1.3.2.orig/board/freescale/mpc8313erdb/mpc8313erdb.c	2009-01-15 10:51:45.000000000 +0100
+++ u-boot-1.3.2/board/freescale/mpc8313erdb/mpc8313erdb.c	2009-01-15 12:18:31.000000000 +0100
@@ -28,6 +28,7 @@
 #endif
 #include <pci.h>
 #include <mpc83xx.h>
+#include <spi.h>
 
 DECLARE_GLOBAL_DATA_PTR;
 
@@ -107,3 +108,29 @@
 #endif
 }
 #endif
+
+
+/*
+ * The following are used to control the SPI chip selects for the SPI command.
+ */
+#ifdef CONFIG_HARD_SPI
+
+void spi_rfid_chipsel(int cs)
+{
+	if(cs)
+		gpio_clear(14);
+	else
+		gpio_set(14);
+}
+
+/*
+ * The SPI command uses this table of functions for controlling the SPI
+ * chip selects.
+ */
+spi_chipsel_type spi_chipsel[] = {
+		spi_rfid_chipsel,
+};
+int spi_chipsel_cnt = sizeof(spi_chipsel) / sizeof(spi_chipsel[0]);
+
+#endif /* CONFIG_HARD_SPI */
+
Index: u-boot-1.3.2/include/configs/MPC8313ERDB.h
===================================================================
--- u-boot-1.3.2.orig/include/configs/MPC8313ERDB.h	2009-01-15 10:51:51.000000000 +0100
+++ u-boot-1.3.2/include/configs/MPC8313ERDB.h	2009-01-15 12:16:57.000000000 +0100
@@ -369,6 +369,7 @@
 #define CONFIG_CMD_PCI
 #define CONFIG_CMD_NAND
 #define CONFIG_CMD_JFFS2
+#define CONFIG_CMD_SPI
 
 #if defined(CFG_RAMBOOT)
     #undef CONFIG_CMD_ENV
@@ -386,6 +387,11 @@
 #define MTDPARTS_DEFAULT	"mtdparts=physmap-flash.0:384k(uboot),64k(env)"
 
 
+/* SPI */
+#define CONFIG_MPC8XXX_SPI
+#define CONFIG_HARD_SPI			/* SPI with hardware support */
+#undef CONFIG_SOFT_SPI			/* SPI bit-banged */
+
 /*
  * Miscellaneous configurable options
  */
Index: u-boot-1.3.2/drivers/spi/mpc8xxx_spi.c
===================================================================
--- u-boot-1.3.2.orig/drivers/spi/mpc8xxx_spi.c	2009-01-15 10:52:30.000000000 +0100
+++ u-boot-1.3.2/drivers/spi/mpc8xxx_spi.c	2009-01-15 10:53:23.000000000 +0100
@@ -34,6 +34,8 @@
 #define SPI_MODE_REV	(0x80000000 >> 5)	/* Reverse mode - MSB first */
 #define SPI_MODE_MS	(0x80000000 >> 6)	/* Always master */
 #define SPI_MODE_EN	(0x80000000 >> 7)	/* Enable interface */
+#define SPI_MODE_DIV16	(0x80000000 >> 4)	/*Divide by 16.   */
+#define SPI_MODE_LEN_8	(0x00700000)		/*0111 8-bit characters*/
 
 #define SPI_TIMEOUT	1000
 
@@ -45,9 +47,7 @@
 	 * SPI pins on the MPC83xx are not muxed, so all we do is initialize
 	 * some registers
 	 */
-	spi->mode = SPI_MODE_REV | SPI_MODE_MS | SPI_MODE_EN;
-	spi->mode = (spi->mode & 0xfff0ffff) | (1 << 16); /* Use SYSCLK / 8
-							     (16.67MHz typ.) */
+	spi->mode = SPI_MODE_DIV16 |SPI_MODE_LEN_8| SPI_MODE_REV | SPI_MODE_MS | SPI_MODE_EN;
 	spi->event = 0xffffffff;	/* Clear all SPI events */
 	spi->mask = 0x00000000;	/* Mask  all SPI interrupts */
 	spi->com = 0;		/* LST bit doesn't do anything, so disregard */