From be3e650d031916b132b4cef9d19e7844cca3440b Mon Sep 17 00:00:00 2001 From: Michael Lauer Date: Fri, 28 Dec 2007 13:10:28 +0000 Subject: rename uboot directory for more consistency --- ....6-fsl-1-Add-the-MPC832XEMDS-board-readme.patch | 131 --------------------- 1 file changed, 131 deletions(-) delete mode 100644 packages/uboot/u-boot-1.1.6/u-boot-1.1.6-fsl-1-Add-the-MPC832XEMDS-board-readme.patch (limited to 'packages/uboot/u-boot-1.1.6/u-boot-1.1.6-fsl-1-Add-the-MPC832XEMDS-board-readme.patch') diff --git a/packages/uboot/u-boot-1.1.6/u-boot-1.1.6-fsl-1-Add-the-MPC832XEMDS-board-readme.patch b/packages/uboot/u-boot-1.1.6/u-boot-1.1.6-fsl-1-Add-the-MPC832XEMDS-board-readme.patch deleted file mode 100644 index b5e2a87b16..0000000000 --- a/packages/uboot/u-boot-1.1.6/u-boot-1.1.6-fsl-1-Add-the-MPC832XEMDS-board-readme.patch +++ /dev/null @@ -1,131 +0,0 @@ -657bdd350516722e4d73329caf37aae694f7eaaa -diff --git a/doc/README.mpc832xemds b/doc/README.mpc832xemds -new file mode 100644 -index 0000000..00c3af1 ---- /dev/null -+++ b/doc/README.mpc832xemds -@@ -0,0 +1,124 @@ -+Freescale MPC832XEMDS Board -+----------------------------------------- -+1. Board Switches and Jumpers -+1.0 There are five Dual-In-Line Packages(DIP) Switches on MPC832XE SYS board -+ For some reason, the HW designers describe the switch settings -+ in terms of 0 and 1, and then map that to physical switches where -+ the label "On" refers to logic 0 and "Off" is logic 1. -+ -+ Switch bits are numbered 1 through, like, 4 6 8 or 10, but the -+ bits may contribute to signals that are numbered based at 0, -+ and some of those signals may be high-bit-number-0 too. Heed -+ well the names and labels and do not get confused. -+ -+ "Off" == 1 -+ "On" == 0 -+ -+ SW3 is switch 18 as silk-screened onto the board. -+ SW4[8] is the bit labled 8 on Switch 4. -+ SW5[1:6] refers to bits labeled 1 through 6 in order on switch 5. -+ SW6[7:1] refers to bits labeled 7 through 1 in order on switch 6. -+ SW7[1:8]= 0000_0001 refers to bits labeled 1 through 6 is set as "On" -+ and bits labeled 8 is set as "Off". -+ -+1.1 For the MPC832XEMDS PROTO Board -+ -+ First, make sure the board default setting is consistent with the -+ document shipped with your board. Then apply the following setting: -+ SW3[1-8]= 0000_1000 (core PLL setting, core enable) -+ SW4[1-8]= 0001_0010 (Flash boot on local bus, system PLL setting) -+ SW5[1-8]= 0010_0110 (Boot from high end) -+ SW6[1-8]= 0011_0100 (Flash boot on 16 bit local bus) -+ SW7[1-8]= 1000_0011 (QE PLL setting) -+ -+ ENET3/4 MII mode settings: -+ J1 1-2 (ETH3_TXER) -+ J2 2-3 (MII mode) -+ J3 2-3 (MII mode) -+ J4 2-3 (ADSL clockOscillator) -+ J5 1-2 (ETH4_TXER) -+ J6 2-3 (ClockOscillator) -+ JP1 removed (don't force PORESET) -+ JP2 mounted (ETH4/2 MII) -+ JP3 mounted (ETH3 MII) -+ JP4 mounted (HRCW from BCSR) -+ -+ ENET3/4 RMII mode settings: -+ J1 1-2 (ETH3_TXER) -+ J2 1-2 (RMII mode) -+ J3 1-2 (RMII mode) -+ J4 2-3 (ADSL clockOscillator) -+ J5 1-2 (ETH4_TXER) -+ J6 2-3 (ClockOscillator) -+ JP1 removed (don't force PORESET) -+ JP2 removed (ETH4/2 RMII) -+ JP3 removed (ETH3 RMII) -+ JP4 removed (HRCW from FLASH) -+ -+ on board Oscillator: 66M -+ -+ -+2. Memory Map -+ -+2.1 The memory map should look pretty much like this: -+ -+ 0x0000_0000 0x7fff_ffff DDR 2G -+ 0x8000_0000 0x8fff_ffff PCI MEM prefetch 256M -+ 0x9000_0000 0x9fff_ffff PCI MEM non-prefetch 256M -+ 0xc000_0000 0xdfff_ffff Empty 512M -+ 0xe000_0000 0xe01f_ffff Int Mem Reg Space 2M -+ 0xe020_0000 0xe02f_ffff Empty 1M -+ 0xe030_0000 0xe03f_ffff PCI IO 1M -+ 0xe040_0000 0xefff_ffff Empty 252M -+ 0xf400_0000 0xf7ff_ffff Empty 64M -+ 0xf800_0000 0xf800_7fff BCSR on CS1 32K -+ 0xf800_8000 0xf800_ffff PIB CS2 32K -+ 0xf801_0000 0xf801_7fff PIB CS3 32K -+ 0xfe00_0000 0xfeff_ffff FLASH on CS0 16M -+ -+ -+3. Definitions -+ -+3.1 Explanation of NEW definitions in: -+ -+ include/configs/MPC832XEMDS.h -+ -+ CONFIG_MPC83XX MPC83XX family for MPC8349, MPC8360 and MPC832X -+ CONFIG_MPC832X MPC832X specific -+ CONFIG_MPC832XEMDS MPC832XEMDS board specific -+ -+4. Compilation -+ -+ Assuming you're using BASH shell: -+ -+ export CROSS_COMPILE=your-cross-compile-prefix -+ cd u-boot -+ make distclean -+ make MPC832XEMDS_config -+ make -+ -+ MPC832X support PCI 33MHz and PCI 66MHz, to make u-boot support PCI: -+ -+ 1)Make sure the DIP SW support PCI mode -+ as described in Section 1.1. -+ -+ 2)To Make U-Boot image support PCI 33MHz, use -+ Make MPC832XEMDS_HOST_33_config -+ -+ 3)To Make U-Boot image support PCI 66MHz, use -+ Make MPC832XEMDS_HOST_66_config -+ -+5. Downloading and Flashing Images -+ -+5.0 Download over network: -+ -+ tftp 20000 u-boot.bin -+ -+5.1 Reflash U-boot Image using U-boot -+ -+ If your current u-boot sets $filesize automatically: -+ -+ protect off fe000000 +$filesize -+ erase fe000000 +$filesize -+ cp.b 20000 fe000000 $filesize -+ -- cgit v1.2.3