| Age | Commit message (Expand) | Author | Files |
|---|
| 2013-04-24 | product info: add newlines after mac addresses, change *-mac to mac-* for con... | Mike Fiore | 1 |
| 2013-04-24 | added attributes wifi-mac, eth-mac, imei, vendor-id to machine types | Mike Fiore | 1 |
| 2013-04-22 | bump driver version | Mike Fiore | 1 |
| 2013-04-22 | add device info to sysfs | Mike Fiore | 1 |
| 2013-03-26 | set reset pins active_low | Jesse Gilles | 1 |
| 2013-03-06 | allow pins with empty attr_name, require name only | Jesse Gilles | 1 |
| 2013-03-01 | add led-a to led-f for MTOCGD3 | Jesse Gilles | 1 |
| 2013-02-28 | more code clean up, rename platform to "mts-io", add mtocgd3 hardware | Jesse Gilles | 2 |
| 2013-02-25 | code cleanup and re-org | Jesse Gilles | 2 |
| 2013-02-19 | Makefile: update clean | Jesse Gilles | 1 |
| 2013-02-19 | add open drain pin type and set multi-drive | Jesse Gilles | 1 |
| 2013-01-14 | read hw_version for MTR, MTR2, log detected board config | Jesse Gilles | 2 |
| 2012-11-08 | add mtr2 rev A support | Jesse Gilles | 1 |
| 2012-10-03 | add extserial-ri for MTR RevA, rename EN4 to MTR2 | Jesse Gilles | 2 |
| 2012-08-22 | fix previous commit | Jesse Gilles | 1 |
| 2012-08-22 | update logging for bluetooth/wifi | Jesse Gilles | 1 |
| 2012-08-22 | add bluetooth, wifi flags and mac addresses | Jesse Gilles | 1 |
| 2012-08-02 | added radio-reset routine for telit module | Jesse Gilles | 1 |
| 2012-07-27 | add open collector pin type, MTR radio reset/init support, fix minor bug | Jesse Gilles | 1 |
| 2012-07-25 | add mtr board support | Jesse Gilles | 2 |
| 2012-06-21 | add led-status for EN4 | Jesse Gilles | 1 |
| 2012-06-08 | en4: set bt-enabled, wlan-enabled low on load | Jesse Gilles | 1 |
| 2012-05-14 | gpio_pin_by_attr_name: allow empty strings | Jesse Gilles | 1 |
| 2012-05-14 | en4: add rs422-term-res, rs485-term-res pins | Jesse Gilles | 1 |
| 2012-05-09 | add eth-switch-enabled for en4, only drive output when low | Jesse Gilles | 1 |
| 2012-05-08 | added serial-mode for en4 | Jesse Gilles | 1 |
| 2012-05-07 | en4: add reset, reset-monitor | Jesse Gilles | 1 |
| 2012-05-07 | add en4 support, reduce some duplication | Jesse Gilles | 2 |
| 2012-01-05 | add daughter card reset (ndc-reset) | Jesse Gilles | 1 |
| 2011-10-03 | add locking on adc read | Jesse Gilles | 1 |
| 2011-09-30 | read one adc at a time | Jesse Gilles | 1 |
| 2011-09-30 | Defined mts_product_id variable to store current product type on driver init.... | Thanh Tran | 2 |
| 2011-09-30 | 1. Used strncmp() to compare only the product name portion of product_ID. | Thanh Tran | 1 |
| 2011-09-27 | rename MT100ECDP to MT100EOCG | Jesse Gilles | 2 |
| 2011-09-14 | Making IO signals logic the same as the stand-alone CDP box. | Thanh Tran | 1 |
| 2011-08-22 | Added control of external DTR and external DCD signals for MT100ECDP. | Thanh Tran | 1 |
| 2011-08-05 | Added support for the embedded CDP module called (MT100ECDP). | Thanh Tran | 2 |
| 2010-12-30 | make TXD1 an input (fixes external serial RX data), bump version to v0.4.1 | Jesse Gilles | 1 |
| 2010-12-17 | fix log typos | Jesse Gilles | 1 |
| 2010-12-17 | fix reading of dout pin state (invert to match output state) | Jesse Gilles | 1 |
| 2010-12-17 | invert dout state: 0 drives output to ground, 1 is open/floating | Jesse Gilles | 1 |
| 2010-09-28 | add usb host power switch debug gpios | James Maki | 1 |
| 2010-09-17 | make max_speed_hz configurable as module params for the spi devices. | James Maki | 1 |
| 2010-09-16 | the spi din should be SPI_CPOL | James Maki | 1 |
| 2010-09-10 | turn off DEBUG | James Maki | 1 |
| 2010-09-10 | clean up formatting | James Maki | 1 |
| 2010-09-09 | check the capabilities array instead of checking against the hw_version | James Maki | 1 |
| 2010-09-09 | copy the eeprom from the platform file instead of overwriting it. | James Maki | 1 |
| 2010-09-09 | cleanup eeprom related stuff. | James Maki | 3 |
| 2010-09-09 | update for MTCDP-1.0 | James Maki | 2 |
