mts-io: add support for 3.12 kernel and all its fun changes

	this commit should build and function for mtocgd and mtocgd2
	support for mtcdp and eocg platforms is not yet implemented

1 files changed, 471 insertions, 489 deletions

diff --git a/io-module/mts_io.c b/io-module/mts_io.c
index b0d2207..79351fa 100644
--- a/io-module/mts_io.c
+++ b/io-module/mts_io.c
@@ -39,6 +39,8 @@
 #include <linux/spi/spi.h>
 #include <linux/i2c/at24.h>
 #include <linux/kmod.h>
+#include <linux/io.h>
+#include <linux/module.h>
 
 #include "mts_io.h"
 
@@ -83,6 +85,8 @@ static int led_mode_status = LED_OFF;
 #define SOUT_LED_SIG3_BIT		BIT(6)
 #define SOUT_EXTSERIAL_DCD_BIT		BIT(7)
 
+#define AT91SAM9X5_BASE_ADC     0xf804c000
+
 /* on-board EEPROM */
 extern uint8_t mts_id_eeprom[512];
 static struct mts_id_eeprom_layout id_eeprom;
@@ -109,6 +113,7 @@ static struct attribute_group *attr_group;
 
 static struct gpio_pin *gpio_pins;
 
+/*
 static struct gpio_pin gpio_pins_mtcdp_0_0[] = {
 	{
 		.name = "ENIO",
@@ -461,300 +466,301 @@ static struct gpio_pin gpio_pins_mt100eocg_0_0[] = {
 	},
 	{ },
 };
+*/
 
 static struct gpio_pin gpio_pins_mtr2_0_0[] = {
 	{
 		.name = "NETH_RST",
-		.attr_name = "eth-switch-enabled",
-		.pin = AT91_PIN_PC6,
-		.direction = GPIO_DIR_OD,
-		.output_value = 1,
-		.use_pullup = 0,
+		.pin = {
+			.gpio = AT91_PIN_PC6,
+			.flags = GPIOF_OPEN_DRAIN | GPIOF_INIT_HIGH,
+			.label = "eth-switch-enabled",
+		},
 	},
 	{
 		.name = "RADIO_RESET",
-		.attr_name = "radio-reset",
-		.pin = AT91_PIN_PC5,
-		.direction = GPIO_DIR_OUTPUT,
-		.output_value = 1,
-		.use_pullup = 0,
+		.pin = {
+			.gpio = AT91_PIN_PC5,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "radio-reset",
+		},
 	},
 	{
 		.name = "RADIO_RESET",
-		.attr_name = "radio-power",
-		.pin = AT91_PIN_PC5,
-		.direction = GPIO_DIR_OUTPUT,
-		.output_value = 1,
-		.use_pullup = 0,
+		.pin = {
+			.gpio = AT91_PIN_PC5,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "radio-power",
+		},
 	},
 	{
 		.name = "DEVICE_RESET",
-		.attr_name = "reset",
-		.pin = AT91_PIN_PC4,
-		.direction = GPIO_DIR_INPUT,
-		.output_value = 0,
-		.use_pullup = 0,
+		.pin = {
+			.gpio = AT91_PIN_PC4,
+			.flags = GPIOF_IN,
+			.label = "reset",
+		},
 		.active_low = 1,
 	},
 	{
 		.name = "LS_LED",
-		.attr_name = "led-ls",
-		.pin = AT91_PIN_PA14,
+		.pin = {
+			.gpio = AT91_PIN_PA14,
 #if LED_LS_CONTROLLABLE
-		.direction = GPIO_DIR_OUTPUT,
+			.flags = GPIOF_OUT_INIT_HIGH,
 #else
-		.direction = GPIO_DIR_INPUT,
+			.flags = GPIOF_IN,
 #endif
-		.output_value = 1,
-		.use_pullup = 0,
+			.label = "led-ls",
+		},
 		.active_low = 1,
 	},
 	{
 		.name = "STATUS_LED",
-		.attr_name = "led-status",
-		.pin = AT91_PIN_PA24,
-		.direction = GPIO_DIR_OUTPUT,
-		.output_value = 0,
-		.use_pullup = 0,
+		.pin = {
+			.gpio = AT91_PIN_PA24,
+			.flags = GPIOF_OUT_INIT_LOW,
+			.label = "led-status",
+		},
 		.active_low = 1,
 	},
 	{
 		.name = "LED7",
-		.attr_name = "led-cd",
-		.pin = AT91_PIN_PA25,
-		.direction = GPIO_DIR_OUTPUT,
-		.output_value = 1,
-		.use_pullup = 0,
+		.pin = {
+			.gpio = AT91_PIN_PA25,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "led-cd",
+		},
 		.active_low = 1,
 	},
 	{
 		.name = "LED7",
-		.attr_name = "led-c",
-		.pin = AT91_PIN_PA25,
-		.direction = GPIO_DIR_OUTPUT,
-		.output_value = 1,
-		.use_pullup = 0,
+		.pin = {
+			.gpio = AT91_PIN_PA25,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "led-c",
+		},
 		.active_low = 1,
 	},
 	{
 		.name = "LED10",
-		.attr_name = "led-sig1",
-		.pin = AT91_PIN_PA26,
-		.direction = GPIO_DIR_OUTPUT,
-		.output_value = 1,
-		.use_pullup = 0,
+		.pin = {
+			.gpio = AT91_PIN_PA26,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "led-sig1",
+		},
 		.active_low = 1,
 	},
 	{
 		.name = "LED10",
-		.attr_name = "led-d",
-		.pin = AT91_PIN_PA26,
-		.direction = GPIO_DIR_OUTPUT,
-		.output_value = 1,
-		.use_pullup = 0,
+		.pin = {
+			.gpio = AT91_PIN_PA26,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "led-d",
+		},
 		.active_low = 1,
 	},
 	{
 		.name = "LED11",
-		.attr_name = "led-sig2",
-		.pin = AT91_PIN_PA27,
-		.direction = GPIO_DIR_OUTPUT,
-		.output_value = 1,
-		.use_pullup = 0,
+		.pin = {
+			.gpio = AT91_PIN_PA27,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "led-sig2",
+		},
 		.active_low = 1,
 	},
 	{
 		.name = "LED11",
-		.attr_name = "led-e",
-		.pin = AT91_PIN_PA27,
-		.direction = GPIO_DIR_OUTPUT,
-		.output_value = 1,
-		.use_pullup = 0,
+		.pin = {
+			.gpio = AT91_PIN_PA27,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "led-e",
+		},
 		.active_low = 1,
 	},
 	{
 		.name = "LED12",
-		.attr_name = "led-sig3",
-		.pin = AT91_PIN_PA28,
-		.direction = GPIO_DIR_OUTPUT,
-		.output_value = 1,
-		.use_pullup = 0,
+		.pin = {
+			.gpio = AT91_PIN_PA28,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "led-sig3",
+		},
 		.active_low = 1,
 	},
 	{
 		.name = "LED12",
-		.attr_name = "led-f",
-		.pin = AT91_PIN_PA28,
-		.direction = GPIO_DIR_OUTPUT,
-		.output_value = 1,
-		.use_pullup = 0,
+		.pin = {
+			.gpio = AT91_PIN_PA28,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "led-f",
+		},
 		.active_low = 1,
 	},
 	{
 		.name = "LED13",
-		.attr_name = "led-wifi",
-		.pin = AT91_PIN_PA29,
-		.direction = GPIO_DIR_OUTPUT,
-		.output_value = 1,
-		.use_pullup = 0,
+		.pin = {
+			.gpio = AT91_PIN_PA29,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "led-wifi",
+		},
 		.active_low = 1,
 	},
 	{
 		.name = "LED13",
-		.attr_name = "led-b",
-		.pin = AT91_PIN_PA29,
-		.direction = GPIO_DIR_OUTPUT,
-		.output_value = 1,
-		.use_pullup = 0,
+		.pin = {
+			.gpio = AT91_PIN_PA29,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "led-b",
+		},
 		.active_low = 1,
 	},
 	{
 		.name = "UART3_DTR",
-		.attr_name = "extserial-dtr",
-		.pin = AT91_PIN_PC12,
-		.direction = GPIO_DIR_INPUT,
-		.output_value = 0,
-		.use_pullup = 0,
+		.pin = {
+			.gpio = AT91_PIN_PC12,
+			.flags = GPIOF_IN,
+			.label = "extserial-dtr",
+		},
 		.active_low = 1,
 	},
 	{
 		.name = "UART3_DSR",
-		.attr_name = "extserial-dsr",
-		.pin = AT91_PIN_PC11,
-		.direction = GPIO_DIR_OUTPUT,
-		.output_value = 1,
-		.use_pullup = 0,
+		.pin = {
+			.gpio = AT91_PIN_PC11,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "extserial-dsr",
+		},
 		.active_low = 1,
 	},
 	{
 		.name = "UART3_DCD",
-		.attr_name = "extserial-dcd",
-		.pin = AT91_PIN_PC10,
-		.direction = GPIO_DIR_OUTPUT,
-		.output_value = 1,
-		.use_pullup = 0,
+		.pin = {
+			.gpio = AT91_PIN_PC10,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "extserial-dcd",
+		},
 		.active_low = 1,
 	},
 	{
 		.name = "UART3_RI",
-		.attr_name = "extserial-ri",
-		.pin = AT91_PIN_PC13,
-		.direction = GPIO_DIR_OUTPUT,
-		.output_value = 1,
-		.use_pullup = 0,
+		.pin = {
+			.gpio = AT91_PIN_PC13,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "extserial-ri",
+		},
 		.active_low = 1,
 	},
 	{
 		.name = "NDC_RESET",
-		.attr_name = "ndc-reset",
-		.pin = AT91_PIN_PC3,
-		.direction = GPIO_DIR_OUTPUT,
-		.output_value = 1,
-		.use_pullup = 0,
+		.pin = {
+			.gpio = AT91_PIN_PC3,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "ndc-reset",
+		},
 	},
 	{
 		.name = "NDC_EEPROM_WRITE_PROTECT",
-		.attr_name = "ndc-eeprom-wp",
-		.pin = AT91_PIN_PC26,
-		.direction = GPIO_DIR_OUTPUT,
-		.output_value = 0,
-		.use_pullup = 0,
+		.pin = {
+			.gpio = AT91_PIN_PC26,
+			.flags = GPIOF_OUT_INIT_LOW,
+			.label = "ndc-eeprom-wp",
+		},
 	},
 	{
 		.name = "BT_EN",
-		.attr_name = "bt-enabled",
-		.pin = AT91_PIN_PD21,
-		.direction = GPIO_DIR_OUTPUT,
-		.output_value = 0,
-		.use_pullup = 0,
+		.pin = {
+			.gpio = AT91_PIN_PD21,
+			.flags = GPIOF_OUT_INIT_LOW,
+			.label = "bt-enabled",
+		},
 	},
 	{
 		.name = "WLAN_EN",
-		.attr_name = "wlan-enabled",
-		.pin = AT91_PIN_PC1,
-		.direction = GPIO_DIR_OUTPUT,
-		.output_value = 0,
-		.use_pullup = 0,
+		.pin = {
+			.gpio = AT91_PIN_PC1,
+			.flags = GPIOF_OUT_INIT_LOW,
+			.label = "wlan-enabled",
+		},
 	},
 	{
 		.name = "SERIAL_MODE0",
-		.attr_name = "serial_mode",
-		.pin = AT91_PIN_PC23,
-		.direction = GPIO_DIR_OUTPUT,
-		.output_value = 0,
-		.use_pullup = 0,
+		.pin = {
+			.gpio = AT91_PIN_PC23,
+			.flags = GPIOF_OUT_INIT_LOW,
+			.label = "serial-mode",
+		},
 	},
 	{
 		.name = "SERIAL_MODE1",
-		.attr_name = "serial_mode",
-		.pin = AT91_PIN_PC24,
-		.direction = GPIO_DIR_OUTPUT,
-		.output_value = 0,
-		.use_pullup = 0,
+		.pin = {
+			.gpio = AT91_PIN_PC24,
+			.flags = GPIOF_OUT_INIT_LOW,
+			.label = "serial-mode",
+		},
 	},
 	{
 		.name = "SERIAL_MODE2",
-		.attr_name = "serial_mode",
-		.pin = AT91_PIN_PC25,
-		.direction = GPIO_DIR_OUTPUT,
-		.output_value = 0,
-		.use_pullup = 0,
+		.pin = {
+			.gpio = AT91_PIN_PC25,
+			.flags = GPIOF_OUT_INIT_LOW,
+			.label = "serial-mode",
+		},
 	},
 	{
 		.name = "RS4XX_TERM_RES",
-		.attr_name = "rs4xx-term-res",
-		.pin = AT91_PIN_PC26,
-		.direction = GPIO_DIR_OUTPUT,
-		.output_value = 0,
-		.use_pullup = 0,
+		.pin = {
+			.gpio = AT91_PIN_PC26,
+			.flags = GPIOF_OUT_INIT_LOW,
+			.label = "rs4xx-term-res",
+		},
 	},
 	{
 		.name = "NDC_GPIO1",
-		.attr_name = "dc-gpio1",
-		.pin = AT91_PIN_PC0,
-		.direction = GPIO_DIR_OUTPUT,
-		.output_value = 0,
-		.use_pullup = 0,
+		.pin = {
+			.gpio = AT91_PIN_PC0,
+			.flags = GPIOF_OUT_INIT_LOW,
+			.label = "dc-gpio1",
+		},
 	},
 	{
 		.name = "NDC_GPIO2",
-		.attr_name = "dc-gpio2",
-		.pin = AT91_PIN_PC14,
-		.direction = GPIO_DIR_OUTPUT,
-		.output_value = 0,
-		.use_pullup = 0,
+		.pin = {
+			.gpio = AT91_PIN_PC14,
+			.flags = GPIOF_OUT_INIT_LOW,
+			.label = "dc-gpio2",
+		},
 	},
 	{
 		.name = "NDC_GPIO3",
-		.attr_name = "dc-gpio3",
-		.pin = AT91_PIN_PC29,
-		.direction = GPIO_DIR_OUTPUT,
-		.output_value = 0,
-		.use_pullup = 0,
+		.pin = {
+			.gpio = AT91_PIN_PC29,
+			.flags = GPIOF_OUT_INIT_LOW,
+			.label = "dc-gpio3",
+		},
 	},
 	{
 		.name = "NDC_GPIO4",
-		.attr_name = "dc-gpio4",
-		.pin = AT91_PIN_PC30,
-		.direction = GPIO_DIR_OUTPUT,
-		.output_value = 0,
-		.use_pullup = 0,
+		.pin = {
+			.gpio = AT91_PIN_PC30,
+			.flags = GPIOF_OUT_INIT_LOW,
+			.label = "dc-gpio4",
+		},
 	},
 	{
 		.name = "NDC_INTERRUPT1",
-		.attr_name = "dc-int1",
-		.pin = AT91_PIN_PC20,
-		.direction = GPIO_DIR_INPUT,
-		.output_value = 0,
-		.use_pullup = 0,
+		.pin = {
+			.gpio = AT91_PIN_PC20,
+			.flags = GPIOF_IN,
+			.label = "dc-int1",
+		},
 	},
 	{
 		.name = "NDC_INTERRUPT2",
-		.attr_name = "dc-int2",
-		.pin = AT91_PIN_PC21,
-		.direction = GPIO_DIR_INPUT,
-		.output_value = 0,
-		.use_pullup = 0,
+		.pin = {
+			.gpio = AT91_PIN_PC21,
+			.flags = GPIOF_IN,
+			.label = "dc-int2",
+		},
 	},
 	{ },
 };
@@ -762,209 +768,208 @@ static struct gpio_pin gpio_pins_mtr2_0_0[] = {
 static struct gpio_pin gpio_pins_mtr_0_0[] = {
 	{
 		.name = "NETH_RST",
-		.attr_name = "eth0-enabled",
-		.pin = AT91_PIN_PC6,
-		.direction = GPIO_DIR_OUTPUT,
-		.output_value = 1,
-		.use_pullup = 0,
+		.pin = {
+			.gpio = AT91_PIN_PC6,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "eth0-enabled",
+		},
 	},
 	{
 		.name = "PWRMON",
-		.attr_name = "radio-power",
-		.pin = AT91_PIN_PA23,
-		.direction = GPIO_DIR_INPUT,
-		.output_value = 0,
-		.use_pullup = 0,
-		.active_low = 0,
+		.pin = {
+			.gpio = AT91_PIN_PA23,
+			.flags = GPIOF_IN,
+			.label = "radio-power",
+		},
 	},
 	{
 		.name = "3G_RST",
-		.attr_name = "radio-reset",
-		.pin = AT91_PIN_PA22,
-		.direction = GPIO_DIR_OD,
-		.output_value = 1,
-		.use_pullup = 0,
+		.pin = {
+			.gpio = AT91_PIN_PA22,
+			.flags = GPIOF_OPEN_DRAIN | GPIOF_INIT_HIGH,
+			.label = "radio-reset",
+		},
 	},
 	{
 		.name = "3G_ONOFF",
-		.attr_name = "radio-enabled",
-		.pin = AT91_PIN_PA21,
-		.direction = GPIO_DIR_OD,
-		.output_value = 1,
-		.use_pullup = 0,
+		.pin = {
+			.gpio = AT91_PIN_PA21,
+			.flags = GPIOF_OPEN_DRAIN | GPIOF_INIT_HIGH,
+			.label = "radio-enabled",
+		},
 	},
 	{
 		.name = "DEVICE_RESET",
-		.attr_name = "reset",
-		.pin = AT91_PIN_PC4,
-		.direction = GPIO_DIR_INPUT,
-		.output_value = 0,
-		.use_pullup = 0,
+		.pin = {
+			.gpio = AT91_PIN_PC4,
+			.flags = GPIOF_IN,
+			.label = "reset",
+		},
 		.active_low = 1,
 	},
 	{
 		.name = "LS_LED",
-		.attr_name = "led-ls",
-		.pin = AT91_PIN_PC16,
+		.pin = {
+			.gpio = AT91_PIN_PC16,
 #if LED_LS_CONTROLLABLE
-		.direction = GPIO_DIR_OUTPUT,
+			.flags = GPIOF_OUT_INIT_HIGH,
 #else
-		.direction = GPIO_DIR_INPUT,
+			.flags = GPIOF_IN,
 #endif
-		.output_value = 1,
-		.use_pullup = 0,
+			.label = "led-ls",
+		},
 		.active_low = 1,
 	},
 	{
 		.name = "STATUS_LED",
-		.attr_name = "led-status",
-		.pin = AT91_PIN_PC21,
-		.direction = GPIO_DIR_OUTPUT,
-		.output_value = 0,
-		.use_pullup = 0,
+		.pin = {
+			.gpio = AT91_PIN_PC21,
+			.flags = GPIOF_OUT_INIT_LOW,
+			.label = "led-status",
+		},
 		.active_low = 1,
 	},
 	{
 		.name = "LED3",
-		.attr_name = "led-wifi",
-		.pin = AT91_PIN_PC15,
-		.direction = GPIO_DIR_OUTPUT,
-		.output_value = 1,
-		.use_pullup = 0,
+		.pin = {
+			.gpio = AT91_PIN_PC15,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "led-wifi",
+		},
 		.active_low = 1,
 	},
 	{
 		.name = "LED3",
-		.attr_name = "led-b",
-		.pin = AT91_PIN_PC15,
-		.direction = GPIO_DIR_OUTPUT,
-		.output_value = 1,
-		.use_pullup = 0,
+		.pin = {
+			.gpio = AT91_PIN_PC15,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "led-b",
+		},
 		.active_low = 1,
 	},
 	{
 		.name = "LED4",
-		.attr_name = "led-cd",
-		.pin = AT91_PIN_PC20,
-		.direction = GPIO_DIR_OUTPUT,
-		.output_value = 1,
-		.use_pullup = 0,
+		.pin = {
+			.gpio = AT91_PIN_PC20,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "led-cd",
+		},
 		.active_low = 1,
 	},
 	{
 		.name = "LED4",
-		.attr_name = "led-c",
-		.pin = AT91_PIN_PC20,
-		.direction = GPIO_DIR_OUTPUT,
-		.output_value = 1,
-		.use_pullup = 0,
+		.pin = {
+			.gpio = AT91_PIN_PC20,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "led-c",
+		},
 		.active_low = 1,
 	},
 	{
 		.name = "LED6",
-		.attr_name = "led-sig1",
-		.pin = AT91_PIN_PC19,
-		.direction = GPIO_DIR_OUTPUT,
-		.output_value = 1,
-		.use_pullup = 0,
+		.pin = {
+			.gpio = AT91_PIN_PC19,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "led-sig1",
+		},
 		.active_low = 1,
 	},
 	{
 		.name = "LED6",
-		.attr_name = "led-d",
-		.pin = AT91_PIN_PC19,
-		.direction = GPIO_DIR_OUTPUT,
-		.output_value = 1,
-		.use_pullup = 0,
+		.pin = {
+			.gpio = AT91_PIN_PC19,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "led-d",
+		},
 		.active_low = 1,
 	},
 	{
 		.name = "LED7",
-		.attr_name = "led-sig2",
-		.pin = AT91_PIN_PC18,
-		.direction = GPIO_DIR_OUTPUT,
-		.output_value = 1,
-		.use_pullup = 0,
+		.pin = {
+			.gpio = AT91_PIN_PC18,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "led-sig2",
+		},
 		.active_low = 1,
 	},
 	{
 		.name = "LED7",
-		.attr_name = "led-e",
-		.pin = AT91_PIN_PC18,
-		.direction = GPIO_DIR_OUTPUT,
-		.output_value = 1,
-		.use_pullup = 0,
+		.pin = {
+			.gpio = AT91_PIN_PC18,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "led-e",
+		},
 		.active_low = 1,
 	},
 	{
 		.name = "LED8",
-		.attr_name = "led-sig3",
-		.pin = AT91_PIN_PC17,
-		.direction = GPIO_DIR_OUTPUT,
-		.output_value = 1,
-		.use_pullup = 0,
+		.pin = {
+			.gpio = AT91_PIN_PC17,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "led-sig3",
+		},
 		.active_low = 1,
 	},
 	{
 		.name = "LED8",
-		.attr_name = "led-f",
-		.pin = AT91_PIN_PC17,
-		.direction = GPIO_DIR_OUTPUT,
-		.output_value = 1,
-		.use_pullup = 0,
+		.pin = {
+			.gpio = AT91_PIN_PC17,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "led-f",
+		},
 		.active_low = 1,
 	},
 	{
 		.name = "RI_B",
-		.attr_name = "extserial-ri",
-		.pin = AT91_PIN_PC25,
-		.direction = GPIO_DIR_OUTPUT,
-		.output_value = 1,
-		.use_pullup = 0,
+		.pin = {
+			.gpio = AT91_PIN_PC25,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "extserial-ri",
+		},
 		.active_low = 1,
 	},
 	{
 		.name = "DTR_B",
-		.attr_name = "extserial-dtr",
-		.pin = AT91_PIN_PC26,
-		.direction = GPIO_DIR_INPUT,
-		.output_value = 0,
-		.use_pullup = 0,
+		.pin = {
+			.gpio = AT91_PIN_PC26,
+			.flags = GPIOF_IN,
+			.label = "extserial-dtr",
+		},
 		.active_low = 1,
 	},
 	{
 		.name = "DSR_B",
-		.attr_name = "extserial-dsr",
-		.pin = AT91_PIN_PC27,
-		.direction = GPIO_DIR_OUTPUT,
-		.output_value = 1,
-		.use_pullup = 0,
+		.pin = {
+			.gpio = AT91_PIN_PC27,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "extserial-dsr",
+		},
 		.active_low = 1,
 	},
 	{
 		.name = "DCD_B",
-		.attr_name = "extserial-dcd",
-		.pin = AT91_PIN_PC28,
-		.direction = GPIO_DIR_OUTPUT,
-		.output_value = 1,
-		.use_pullup = 0,
+		.pin = {
+			.gpio = AT91_PIN_PC28,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "extserial-dcd",
+		},
 		.active_low = 1,
 	},
 	{
 		.name = "BT_EN",
-		.attr_name = "bt-enabled",
-		.pin = AT91_PIN_PA28,
-		.direction = GPIO_DIR_OUTPUT,
-		.output_value = 0,
-		.use_pullup = 0,
+		.pin = {
+			.gpio = AT91_PIN_PA28,
+			.flags = GPIOF_OUT_INIT_LOW,
+			.label = "bt-enabled",
+		},
 	},
 	{
 		.name = "WLAN_EN",
-		.attr_name = "wlan-enabled",
-		.pin = AT91_PIN_PA27,
-		.direction = GPIO_DIR_OUTPUT,
-		.output_value = 0,
-		.use_pullup = 0,
+		.pin = {
+			.gpio = AT91_PIN_PA27,
+			.flags = GPIOF_OUT_INIT_LOW,
+			.label = "wlan-enabled",
+		},
 	},
 	{ },
 };
@@ -972,209 +977,208 @@ static struct gpio_pin gpio_pins_mtr_0_0[] = {
 static struct gpio_pin gpio_pins_mtr_0_1[] = {
 	{
 		.name = "NETH_RST",
-		.attr_name = "eth0-enabled",
-		.pin = AT91_PIN_PC6,
-		.direction = GPIO_DIR_OUTPUT,
-		.output_value = 1,
-		.use_pullup = 0,
+		.pin = {
+			.gpio = AT91_PIN_PC6,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "eth0-enabled",
+		},
 	},
 	{
 		.name = "PWRMON",
-		.attr_name = "radio-power",
-		.pin = AT91_PIN_PA23,
-		.direction = GPIO_DIR_INPUT,
-		.output_value = 0,
-		.use_pullup = 0,
-		.active_low = 0,
+		.pin = {
+			.gpio = AT91_PIN_PA23,
+			.flags = GPIOF_IN,
+			.label = "radio-power",
+		},
 	},
 	{
 		.name = "3G_RST",
-		.attr_name = "radio-reset",
-		.pin = AT91_PIN_PA22,
-		.direction = GPIO_DIR_OUTPUT,
-		.output_value = 1,
-		.use_pullup = 1,
+		.pin = {
+			.gpio = AT91_PIN_PA22,
+			.flags = GPIOF_OUT_INIT_HIGH | GPIOF_PULLUP,
+			.label = "radio-reset",
+		},
 	},
 	{
 		.name = "3G_ONOFF",
-		.attr_name = "radio-enabled",
-		.pin = AT91_PIN_PA21,
-		.direction = GPIO_DIR_OUTPUT,
-		.output_value = 1,
-		.use_pullup = 1,
+		.pin = {
+			.gpio = AT91_PIN_PA21,
+			.flags = GPIOF_OUT_INIT_HIGH | GPIOF_PULLUP,
+			.label = "radio-enabled",
+		},
 	},
 	{
 		.name = "DEVICE_RESET",
-		.attr_name = "reset",
-		.pin = AT91_PIN_PC4,
-		.direction = GPIO_DIR_INPUT,
-		.output_value = 0,
-		.use_pullup = 0,
+		.pin = {
+			.gpio = AT91_PIN_PC4,
+			.flags = GPIOF_IN,
+			.label = "reset",
+		},
 		.active_low = 1,
 	},
 	{
 		.name = "LS_LED",
-		.attr_name = "led-ls",
-		.pin = AT91_PIN_PC16,
+		.pin = {
+			.gpio = AT91_PIN_PC16,
 #if LED_LS_CONTROLLABLE
-		.direction = GPIO_DIR_OUTPUT,
+			.flags = GPIOF_OUT_INIT_HIGH,
 #else
-		.direction = GPIO_DIR_INPUT,
+			.flags = GPIOF_IN,
 #endif
-		.output_value = 1,
-		.use_pullup = 0,
+			.label = "led-ls",
+		},
 		.active_low = 1,
 	},
 	{
 		.name = "STATUS_LED",
-		.attr_name = "led-status",
-		.pin = AT91_PIN_PC21,
-		.direction = GPIO_DIR_OUTPUT,
-		.output_value = 0,
-		.use_pullup = 0,
+		.pin = {
+			.gpio = AT91_PIN_PC21,
+			.flags = GPIOF_OUT_INIT_LOW,
+			.label = "led-status",
+		},
 		.active_low = 1,
 	},
 	{
 		.name = "LED3",
-		.attr_name = "led-wifi",
-		.pin = AT91_PIN_PC15,
-		.direction = GPIO_DIR_OUTPUT,
-		.output_value = 1,
-		.use_pullup = 0,
+		.pin = {
+			.gpio = AT91_PIN_PC15,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "led-wifi",
+		},
 		.active_low = 1,
 	},
 	{
 		.name = "LED3",
-		.attr_name = "led-b",
-		.pin = AT91_PIN_PC15,
-		.direction = GPIO_DIR_OUTPUT,
-		.output_value = 1,
-		.use_pullup = 0,
+		.pin = {
+			.gpio = AT91_PIN_PC15,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "led-b",
+		},
 		.active_low = 1,
 	},
 	{
 		.name = "LED4",
-		.attr_name = "led-cd",
-		.pin = AT91_PIN_PC20,
-		.direction = GPIO_DIR_OUTPUT,
-		.output_value = 1,
-		.use_pullup = 0,
+		.pin = {
+			.gpio = AT91_PIN_PC20,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "led-cd",
+		},
 		.active_low = 1,
 	},
 	{
 		.name = "LED4",
-		.attr_name = "led-c",
-		.pin = AT91_PIN_PC20,
-		.direction = GPIO_DIR_OUTPUT,
-		.output_value = 1,
-		.use_pullup = 0,
+		.pin = {
+			.gpio = AT91_PIN_PC20,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "led-c",
+		},
 		.active_low = 1,
 	},
 	{
 		.name = "LED6",
-		.attr_name = "led-sig1",
-		.pin = AT91_PIN_PC19,
-		.direction = GPIO_DIR_OUTPUT,
-		.output_value = 1,
-		.use_pullup = 0,
+		.pin = {
+			.gpio = AT91_PIN_PC19,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "led-sig1",
+		},
 		.active_low = 1,
 	},
 	{
 		.name = "LED6",
-		.attr_name = "led-d",
-		.pin = AT91_PIN_PC19,
-		.direction = GPIO_DIR_OUTPUT,
-		.output_value = 1,
-		.use_pullup = 0,
+		.pin = {
+			.gpio = AT91_PIN_PC19,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "led-d",
+		},
 		.active_low = 1,
 	},
 	{
 		.name = "LED7",
-		.attr_name = "led-sig2",
-		.pin = AT91_PIN_PC18,
-		.direction = GPIO_DIR_OUTPUT,
-		.output_value = 1,
-		.use_pullup = 0,
+		.pin = {
+			.gpio = AT91_PIN_PC18,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "led-sig2",
+		},
 		.active_low = 1,
 	},
 	{
 		.name = "LED7",
-		.attr_name = "led-e",
-		.pin = AT91_PIN_PC18,
-		.direction = GPIO_DIR_OUTPUT,
-		.output_value = 1,
-		.use_pullup = 0,
+		.pin = {
+			.gpio = AT91_PIN_PC18,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "led-e",
+		},
 		.active_low = 1,
 	},
 	{
 		.name = "LED8",
-		.attr_name = "led-sig3",
-		.pin = AT91_PIN_PC17,
-		.direction = GPIO_DIR_OUTPUT,
-		.output_value = 1,
-		.use_pullup = 0,
+		.pin = {
+			.gpio = AT91_PIN_PC17,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "led-sig3",
+		},
 		.active_low = 1,
 	},
 	{
 		.name = "LED8",
-		.attr_name = "led-f",
-		.pin = AT91_PIN_PC17,
-		.direction = GPIO_DIR_OUTPUT,
-		.output_value = 1,
-		.use_pullup = 0,
+		.pin = {
+			.gpio = AT91_PIN_PC17,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "led-f",
+		},
 		.active_low = 1,
 	},
 	{
 		.name = "RI_B",
-		.attr_name = "extserial-ri",
-		.pin = AT91_PIN_PC25,
-		.direction = GPIO_DIR_OUTPUT,
-		.output_value = 1,
-		.use_pullup = 0,
+		.pin = {
+			.gpio = AT91_PIN_PC25,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "extserial-ri",
+		},
 		.active_low = 1,
 	},
 	{
 		.name = "DTR_B",
-		.attr_name = "extserial-dtr",
-		.pin = AT91_PIN_PC26,
-		.direction = GPIO_DIR_INPUT,
-		.output_value = 0,
-		.use_pullup = 0,
+		.pin = {
+			.gpio = AT91_PIN_PC26,
+			.flags = GPIOF_IN,
+			.label = "extserial-dtr",
+		},
 		.active_low = 1,
 	},
 	{
 		.name = "DSR_B",
-		.attr_name = "extserial-dsr",
-		.pin = AT91_PIN_PC27,
-		.direction = GPIO_DIR_OUTPUT,
-		.output_value = 1,
-		.use_pullup = 0,
+		.pin = {
+			.gpio = AT91_PIN_PC27,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "extserial-dsr",
+		},
 		.active_low = 1,
 	},
 	{
 		.name = "DCD_B",
-		.attr_name = "extserial-dcd",
-		.pin = AT91_PIN_PC28,
-		.direction = GPIO_DIR_OUTPUT,
-		.output_value = 1,
-		.use_pullup = 0,
+		.pin = {
+			.gpio = AT91_PIN_PC28,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "extserial-dcd",
+		},
 		.active_low = 1,
 	},
 	{
 		.name = "BT_EN",
-		.attr_name = "bt-enabled",
-		.pin = AT91_PIN_PA28,
-		.direction = GPIO_DIR_OUTPUT,
-		.output_value = 0,
-		.use_pullup = 0,
+		.pin = {
+			.gpio = AT91_PIN_PA28,
+			.flags = GPIOF_OUT_INIT_LOW,
+			.label = "bt-enabled",
+		},
 	},
 	{
 		.name = "WLAN_EN",
-		.attr_name = "wlan-enabled",
-		.pin = AT91_PIN_PA27,
-		.direction = GPIO_DIR_OUTPUT,
-		.output_value = 0,
-		.use_pullup = 0,
+		.pin = {
+			.gpio = AT91_PIN_PA27,
+			.flags = GPIOF_OUT_INIT_LOW,
+			.label = "wlan-enabled",
+		},
 	},
 	{ },
 };
@@ -1197,7 +1201,7 @@ struct gpio_pin *gpio_pin_by_attr_name(const char *name) {
 	struct gpio_pin *pin;
 
 	for (pin = gpio_pins; *pin->name; pin++) {
-		if (!strcmp(pin->attr_name, name)) {
+		if (!strcmp(pin->pin.label, name)) {
 			return pin;
 		}
 	}
@@ -1361,7 +1365,7 @@ static void blink_callback(struct work_struct *ignored)
 
 	pin = gpio_pin_by_name("DEVICE_RESET");
 	if (pin) {
-		reset_pressed = !at91_get_gpio_value(pin->pin);
+		reset_pressed = !gpio_get_value(pin->pin.gpio);
 	}
 
 	if (reset_pid > 0) {
@@ -1393,7 +1397,7 @@ static void blink_callback(struct work_struct *ignored)
 	if (led_mode_status == LED_FLASHING) {
 		pin = gpio_pin_by_name("STATUS_LED");
 		if (pin) {
-			at91_set_gpio_value(pin->pin, !at91_get_gpio_value(pin->pin));
+			gpio_set_value(pin->pin.gpio, !gpio_get_value(pin->pin.gpio));
 		}
 	}
 
@@ -1413,7 +1417,7 @@ static int radio_off_telit(void)
 		return -ENODEV;
 	}
 
-	value = at91_get_gpio_value(pwrmon_pin->pin);
+	value = gpio_get_value(pwrmon_pin->pin.gpio);
 	if(value == 0) {
 		log_error("radio is already off");
 		return -EINVAL;
@@ -1421,7 +1425,7 @@ static int radio_off_telit(void)
 
 	// drive on/off pin low for at least 3 sec
 	log_info("shutting down radio");
-	ret = at91_set_gpio_output_with_pullup(onoff_pin->pin, 0, onoff_pin->use_pullup);
+	ret = gpio_direction_output_pullup(onoff_pin->pin.gpio, 0, onoff_pin->pin.flags & GPIOF_PULLUP);
 	if (ret) {
 		return ret;
 	}
@@ -1429,7 +1433,7 @@ static int radio_off_telit(void)
 	msleep(3500);
 
 	// set on/off pin high
-	ret = at91_set_gpio_output_with_pullup(onoff_pin->pin, 1, onoff_pin->use_pullup);
+	ret = gpio_direction_output_pullup(onoff_pin->pin.gpio, 1, onoff_pin->pin.flags & GPIOF_PULLUP);
 	if (ret) {
 		return ret;
 	}
@@ -1438,11 +1442,11 @@ static int radio_off_telit(void)
 	msleep(5000);
 
 	// check that power is low
-	value = at91_get_gpio_value(pwrmon_pin->pin);
+	value = gpio_get_value(pwrmon_pin->pin.gpio);
 	if(value != 0) {
 		log_warning("radio is still on. performing radio reset.");
 		//Perform Hard Reset
-		ret = at91_set_gpio_output_with_pullup(rst_pin->pin, 0, rst_pin->use_pullup);
+		ret = gpio_direction_output_pullup(rst_pin->pin.gpio, 0, rst_pin->pin.flags & GPIOF_PULLUP);
 		if (ret) {
 			return ret;
 		}
@@ -1450,7 +1454,7 @@ static int radio_off_telit(void)
 		msleep(500);
 
 		// set pin high
-		ret = at91_set_gpio_output_with_pullup(rst_pin->pin, 1, rst_pin->use_pullup);
+		ret = gpio_direction_output_pullup(rst_pin->pin.gpio, 1, rst_pin->pin.flags & GPIOF_PULLUP);
 		if (ret) {
 			return ret;
 		}
@@ -1472,7 +1476,7 @@ static int radio_on_telit(void)
 		return -ENODEV;
 	}
 
-	value = at91_get_gpio_value(pwrmon_pin->pin);
+	value = gpio_get_value(pwrmon_pin->pin.gpio);
 	if(value != 0) {
 		log_error("radio is already on");
 		return -EINVAL;
@@ -1480,7 +1484,7 @@ static int radio_on_telit(void)
 
 	// drive on/off pin low for at least 5 sec
 	log_info("turning on radio");
-	ret = at91_set_gpio_output_with_pullup(onoff_pin->pin, 0, onoff_pin->use_pullup);
+	ret = gpio_direction_output_pullup(onoff_pin->pin.gpio, 0, onoff_pin->pin.flags & GPIOF_PULLUP);
 	if (ret) {
 		return ret;
 	}
@@ -1488,7 +1492,7 @@ static int radio_on_telit(void)
 	msleep(5500);
 
 	// set on/off pin high
-	ret = at91_set_gpio_output_with_pullup(onoff_pin->pin, 1, onoff_pin->use_pullup);
+	ret = gpio_direction_output_pullup(onoff_pin->pin.gpio, 1, onoff_pin->pin.flags & GPIOF_PULLUP);
 	if (ret) {
 		return ret;
 	}
@@ -1496,11 +1500,11 @@ static int radio_on_telit(void)
 	msleep(200);
 
 	// check that power is high
-	value = at91_get_gpio_value(pwrmon_pin->pin);
+	value = gpio_get_value(pwrmon_pin->pin.gpio);
 	if(value == 0) {
 		log_warning("radio is still off. performing radio reset");
 		//Perform Hard Reset
-		ret = at91_set_gpio_output_with_pullup(rst_pin->pin, 0, rst_pin->use_pullup);
+		ret = gpio_direction_output_pullup(rst_pin->pin.gpio, 0, rst_pin->pin.flags & GPIOF_PULLUP);
 		if (ret) {
 			return ret;
 		}
@@ -1508,7 +1512,7 @@ static int radio_on_telit(void)
 		msleep(500);
 
 		// set pin high
-		ret = at91_set_gpio_output_with_pullup(rst_pin->pin, 1, rst_pin->use_pullup);
+		ret = gpio_direction_output_pullup(rst_pin->pin.gpio, 1, rst_pin->pin.flags & GPIOF_PULLUP);
 		if (ret) {
 			return ret;
 		}
@@ -1556,7 +1560,7 @@ static int radio_reset_telit(void)
 	}
 
 	// drive reset pin low for 500ms
-	ret = at91_set_gpio_output_with_pullup(rst_pin->pin, 0, rst_pin->use_pullup);
+	ret = gpio_direction_output_pullup(rst_pin->pin.gpio, 0, rst_pin->pin.flags & GPIOF_PULLUP);
 	if (ret) {
 		return ret;
 	}
@@ -1564,7 +1568,7 @@ static int radio_reset_telit(void)
 	msleep(500);
 
 	// set pin high
-	ret = at91_set_gpio_output_with_pullup(rst_pin->pin, 1, rst_pin->use_pullup);
+	ret = gpio_direction_output_pullup(rst_pin->pin.gpio, 1, rst_pin->pin.flags & GPIOF_PULLUP);
 	if (ret) {
 		return ret;
 	}
@@ -1573,7 +1577,7 @@ static int radio_reset_telit(void)
 	msleep(2000);
 
 	// drive on/off pin low for 6 sec
-	ret = at91_set_gpio_output_with_pullup(onoff_pin->pin, 0, onoff_pin->use_pullup);
+	ret = gpio_direction_output_pullup(onoff_pin->pin.gpio, 0, onoff_pin->pin.flags & GPIOF_PULLUP);
 	if (ret) {
 		return ret;
 	}
@@ -1581,7 +1585,7 @@ static int radio_reset_telit(void)
 	msleep(6000);
 
 	// set on/off pin high
-	ret = at91_set_gpio_output_with_pullup(onoff_pin->pin, 1, onoff_pin->use_pullup);
+	ret = gpio_direction_output_pullup(onoff_pin->pin.gpio, 1, onoff_pin->pin.flags & GPIOF_PULLUP);
 	if (ret) {
 		return ret;
 	}
@@ -1591,44 +1595,36 @@ static int radio_reset_telit(void)
 
 static int radio_reset(void)
 {
-	int ret;
 	struct gpio_pin *pin = gpio_pin_by_name("RADIO_RESET");
 
 	if (!pin) {
 		return -ENODEV;
 	}
 
-	ret = at91_set_gpio_value(pin->pin, 0);
-	if (ret) {
-		return ret;
-	}
+	gpio_set_value(pin->pin.gpio, 0);
 
 	mdelay(250);
 
-	ret = at91_set_gpio_value(pin->pin, 1);
+	gpio_set_value(pin->pin.gpio, 1);
 
-	return ret;
+	return 0;
 }
 
 static int ndc_reset(void)
 {
-	int ret;
 	struct gpio_pin *pin = gpio_pin_by_name("NDC_RESET");
 
 	if (!pin) {
 		return -ENODEV;
 	}
 
-	ret = at91_set_gpio_value(pin->pin, 0);
-	if (ret) {
-		return ret;
-	}
+	gpio_set_value(pin->pin.gpio, 0);
 
 	mdelay(1);
 
-	ret = at91_set_gpio_value(pin->pin, 1);
+	gpio_set_value(pin->pin.gpio, 1);
 
-	return ret;
+	return 0;
 }
 
 static int ADT7302_to_celsius(int value)
@@ -1655,7 +1651,7 @@ static ssize_t mts_attr_show_gpio_pin(struct device *dev,
 
 	mutex_lock(&mts_io_mutex);
 
-	value = at91_get_gpio_value(pin->pin);
+	value = gpio_get_value(pin->pin.gpio);
 
 	mutex_unlock(&mts_io_mutex);
 
@@ -1674,7 +1670,6 @@ static ssize_t mts_attr_store_gpio_pin(struct device *dev,
 		struct device_attribute *attr, const char *buf, size_t count)
 {
 	int value;
-	int err;
 	struct gpio_pin *pin = gpio_pin_by_attr_name(attr->attr.name);
 
 	if (!pin) {
@@ -1691,14 +1686,10 @@ static ssize_t mts_attr_store_gpio_pin(struct device *dev,
 
 	mutex_lock(&mts_io_mutex);
 
-	err = at91_set_gpio_value(pin->pin, value);
+	gpio_set_value(pin->pin.gpio, value);
 
 	mutex_unlock(&mts_io_mutex);
 
-	if (err) {
-		return err;
-	}
-
 	return count;
 }
 
@@ -2142,19 +2133,19 @@ static ssize_t mts_attr_store_led_status(struct device *dev,
 	switch (value) {
 	case LED_OFF:
 		led_mode_status = LED_OFF;
-		ret = at91_set_gpio_value(pin->pin, 1);
+		gpio_set_value(pin->pin.gpio, 1);
 
 		break;
 
 	case LED_ON:
 		led_mode_status = LED_ON;
-		ret = at91_set_gpio_value(pin->pin, 0);
+		gpio_set_value(pin->pin.gpio, 0);
 
 		break;
 
 	case LED_FLASHING:
 		led_mode_status = LED_FLASHING;
-		ret = at91_set_gpio_value(pin->pin, 0);
+		gpio_set_value(pin->pin.gpio, 0);
 
 		break;
 
@@ -2423,9 +2414,9 @@ static ssize_t mts_attr_show_serial_mode(struct device *dev,
 
 	mutex_lock(&mts_io_mutex);
 
-	smode0 = at91_get_gpio_value(pin_smode0->pin);
-	smode1 = at91_get_gpio_value(pin_smode1->pin);
-	smode2 = at91_get_gpio_value(pin_smode2->pin);
+	smode0 = gpio_get_value(pin_smode0->pin.gpio);
+	smode1 = gpio_get_value(pin_smode1->pin.gpio);
+	smode2 = gpio_get_value(pin_smode2->pin.gpio);
 
 	if (smode2 == 0 && smode1 == 0 && smode0 == 1)
 		ret = sprintf(buf, "rs232\n");
@@ -2482,9 +2473,9 @@ static ssize_t mts_attr_store_serial_mode(struct device *dev,
 
 	mutex_lock(&mts_io_mutex);
 
-	at91_set_gpio_value(pin_smode2->pin, smode2);
-	at91_set_gpio_value(pin_smode1->pin, smode1);
-	at91_set_gpio_value(pin_smode0->pin, smode0);
+	gpio_set_value(pin_smode2->pin.gpio, smode2);
+	gpio_set_value(pin_smode1->pin.gpio, smode1);
+	gpio_set_value(pin_smode0->pin.gpio, smode0);
 
 	mutex_unlock(&mts_io_mutex);
 
@@ -2580,7 +2571,7 @@ struct gpio_pin *dc_gpio_pin_by_attr_name(const char *name) {
 	}
 
 	for (pin = gpio_pins; *pin->name; pin++) {
-		if (!strcmp(pin->attr_name, pin_attr_name)) {
+		if (!strcmp(pin->pin.label, pin_attr_name)) {
 			return pin;
 		}
 	}
@@ -2604,7 +2595,7 @@ static ssize_t mts_attr_show_dc_gpio_pin(struct device *dev,
 
 	mutex_lock(&mts_io_mutex);
 
-	value = at91_get_gpio_value(pin->pin);
+	value = gpio_get_value(pin->pin.gpio);
 
 	mutex_unlock(&mts_io_mutex);
 
@@ -2623,7 +2614,6 @@ static ssize_t mts_attr_store_dc_gpio_pin(struct device *dev,
 		struct device_attribute *attr, const char *buf, size_t count)
 {
 	int value;
-	int err;
 	struct gpio_pin *pin = dc_gpio_pin_by_attr_name(attr->attr.name);
 
 	if (!pin) {
@@ -2640,14 +2630,10 @@ static ssize_t mts_attr_store_dc_gpio_pin(struct device *dev,
 
 	mutex_lock(&mts_io_mutex);
 
-	err = at91_set_gpio_value(pin->pin, value);
+	gpio_set_value(pin->pin.gpio, value);
 
 	mutex_unlock(&mts_io_mutex);
 
-	if (err) {
-		return err;
-	}
-
 	return count;
 }
 
@@ -3112,7 +3098,7 @@ static struct attribute_group mtr_platform_attribute_group = {
 
 static struct platform_device *mts_io_platform_device;
 
-static int __devinit mts_spi_sout_probe(struct spi_device *spi)
+static int mts_spi_sout_probe(struct spi_device *spi)
 {
 	int tmp;
 
@@ -3150,10 +3136,10 @@ static struct spi_driver mts_spi_sout_driver = {
 	},
 
 	.probe = mts_spi_sout_probe,
-	.remove = __devexit_p(mts_spi_sout_remove),
+	.remove = mts_spi_sout_remove,
 };
 
-static int __devinit mts_spi_dout_probe(struct spi_device *spi)
+static int mts_spi_dout_probe(struct spi_device *spi)
 {
 	int tmp;
 
@@ -3196,10 +3182,10 @@ static struct spi_driver mts_spi_dout_driver = {
 	},
 
 	.probe = mts_spi_dout_probe,
-	.remove = __devexit_p(mts_spi_dout_remove),
+	.remove = mts_spi_dout_remove,
 };
 
-static int __devinit mts_spi_din_probe(struct spi_device *spi)
+static int mts_spi_din_probe(struct spi_device *spi)
 {
 	int tmp;
 
@@ -3239,10 +3225,10 @@ static struct spi_driver mts_spi_din_driver = {
 	},
 
 	.probe = mts_spi_din_probe,
-	.remove = __devexit_p(mts_spi_din_remove),
+	.remove = mts_spi_din_remove,
 };
 
-static int __devinit mts_spi_dc_dout_probe(struct spi_device *spi)
+static int mts_spi_dc_dout_probe(struct spi_device *spi)
 {
 	int tmp;
 
@@ -3285,10 +3271,10 @@ static struct spi_driver mts_spi_dc_dout_driver = {
 	},
 
 	.probe = mts_spi_dc_dout_probe,
-	.remove = __devexit_p(mts_spi_dc_dout_remove),
+	.remove = mts_spi_dc_dout_remove,
 };
 
-static int __devinit mts_spi_dc_din_probe(struct spi_device *spi)
+static int mts_spi_dc_din_probe(struct spi_device *spi)
 {
 	int tmp;
 
@@ -3328,10 +3314,10 @@ static struct spi_driver mts_spi_dc_din_driver = {
 	},
 
 	.probe = mts_spi_dc_din_probe,
-	.remove = __devexit_p(mts_spi_dc_din_remove),
+	.remove = mts_spi_dc_din_remove,
 };
 
-static int __devinit mts_spi_dc_adc_probe(struct spi_device *spi)
+static int mts_spi_dc_adc_probe(struct spi_device *spi)
 {
 	int tmp;
 
@@ -3372,10 +3358,10 @@ static struct spi_driver mts_spi_dc_adc_driver = {
 	},
 
 	.probe = mts_spi_dc_adc_probe,
-	.remove = __devexit_p(mts_spi_dc_adc_remove),
+	.remove = mts_spi_dc_adc_remove,
 };
 
-static int __devinit mts_spi_board_temp_probe(struct spi_device *spi)
+static int mts_spi_board_temp_probe(struct spi_device *spi)
 {
 	int tmp;
 
@@ -3410,7 +3396,7 @@ static struct spi_driver mts_spi_board_temp_driver = {
 	},
 
 	.probe = mts_spi_board_temp_probe,
-	.remove = __devexit_p(mts_spi_board_temp_remove),
+	.remove = mts_spi_board_temp_remove,
 };
 
 static int mts_dc_eeprom_load(void)
@@ -3456,6 +3442,7 @@ static int mts_id_eeprom_load(void)
 	if (mts_id_eeprom[0] == 0xFF) {
 		log_error("uninitialized eeprom");
 		return -EIO;
+		/*
 	} else if (mts_id_eeprom[0] == 0x00) {
 		strncpy(id_eeprom.vendor_id, VENDOR_ID_MULTITECH, sizeof(id_eeprom.vendor_id) - 1);
 		strncpy(id_eeprom.product_id, PRODUCT_ID_MTCDP_E1_DK, sizeof(id_eeprom.product_id) - 1);
@@ -3477,6 +3464,7 @@ static int mts_id_eeprom_load(void)
 		has_spi_dout = 1;
 		has_spi_temp = 1;
 		log_info("detected board %s", HW_VERSION_MT100EOCG_0_0);
+		*/
 	} else if (strncmp(id_eeprom.hw_version, HW_VERSION_MTR2_0_0, strlen(HW_VERSION_MTR2_0_0)) == 0) {
 		attr_group = &mtr2_platform_attribute_group;
 		gpio_pins = gpio_pins_mtr2_0_0;
@@ -3533,6 +3521,7 @@ static int mts_id_eeprom_load(void)
 		has_spi_dout = 0;
 		has_spi_temp = 0;
 		log_info("detected board %s", HW_VERSION_MTOCGD_0_1);
+		/*
 	} else {
 		attr_group = &mtcdp_platform_attribute_group;
 		gpio_pins = gpio_pins_mtcdp_1_0;
@@ -3542,6 +3531,7 @@ static int mts_id_eeprom_load(void)
 		has_spi_dout = 1;
 		has_spi_temp = 1;
 		log_info("detected board %s", HW_VERSION_MTCDP_1_0);
+		*/
 	}
 
 	log_info("sizeof: %lu", (unsigned long) sizeof(struct mts_id_eeprom_layout));
@@ -3698,7 +3688,7 @@ static int __init mts_io_init(void)
 		}
 	}
 
-#ifdef CONFIG_ARCH_AT91SAM9X5
+#ifdef CONFIG_SOC_AT91SAM9X5
 	adc_base = ioremap(AT91SAM9X5_BASE_ADC, SZ_16K);
 #else
 	adc_base = ioremap(AT91SAM9260_BASE_ADC, SZ_16K);
@@ -3721,24 +3711,16 @@ static int __init mts_io_init(void)
 	}
 
 	for (pin = gpio_pins; *pin->name; pin++) {
-		gpio_request(pin->pin, pin->name);
-
-		if (pin->direction == GPIO_DIR_OD) {
-			log_info("Setting pin %s to multi-drive\n", pin->name);
-			at91_set_multi_drive(pin->pin, true);
-		}
-
-		if (pin->direction == GPIO_DIR_OUTPUT || pin->direction == GPIO_DIR_OD) {
-			at91_set_gpio_output_with_pullup(pin->pin, pin->output_value, pin->use_pullup);
-		} else {
-			at91_set_gpio_input(pin->pin, pin->use_pullup);
+		ret = gpio_request_one(pin->pin.gpio, pin->pin.flags, pin->pin.label);
+		if (ret) {
+			log_debug("could not request pin %s (%d) but it could have already been requested under a different pin name", pin->name, ret);
 		}
 	}
 
 	if ( has_spi_sout || has_spi_dout || has_spi_din ) {
 		pin = gpio_pin_by_name("ENIO");
 		if (pin) {
-			at91_set_gpio_value(pin->pin, 0);
+			gpio_set_value(pin->pin.gpio, 0);
 		}
 	}