mts-io based on thud/4.19 kernel for mt100eocg4.3.1

6 files changed, 4450 insertions, 0 deletions

diff --git a/io-module/machine/mt100eocg.c b/io-module/machine/mt100eocg.c
new file mode 100644
index 0000000..749b85a
--- /dev/null
+++ b/io-module/machine/mt100eocg.c
@@ -0,0 +1,252 @@
+#include "at91gpio.h"
+/* Used for both MT100EOCG 0.0 */
+static struct gpio_pin gpio_pins_mt100eocg_0_0[] = {
+	{	
+		.name = "ADC0",
+		.pin = {
+			.label = "adc0",
+			.gpio = AT91_PIN_PC0,
+			.flags = GPIOF_IN,
+		},
+	},
+	{
+		.name = "ADC1",
+		.pin = {
+			.label = "adc1",
+			.gpio = AT91_PIN_PC1,
+			.flags = GPIOF_IN,
+		},
+	},
+	{
+		.name = "ADC2",
+		.pin = {
+			.label = "adc2",
+			.gpio = AT91_PIN_PC2,
+			.flags = GPIOF_IN,
+		},
+	},
+	{
+		.name = "ADC3",
+		.pin = {
+			.label = "adc3",
+			.gpio = AT91_PIN_PC3,
+			.flags = GPIOF_IN,
+		},
+	},
+	{
+		.name = "DTR1",
+		.pin = {
+			.label = "extserial-dtr",
+			.gpio = AT91_PIN_PB18,
+			.flags = GPIOF_IN,
+		},
+		.active_low = 1,
+	},
+	{
+		.name = "DCD1",
+		.pin = {
+			.label = "extserial-dcd",
+			.gpio = AT91_PIN_PB3,
+			.flags = GPIOF_OUT_INIT_HIGH,
+		},
+		.active_low = 1,
+	},	
+	{
+		.name = "ETH0_ENABLED",
+		.pin = {
+			.label = "eth0-enabled",
+			.gpio = AT91_PIN_PB31,
+			.flags = GPIOF_OUT_INIT_HIGH,
+		},
+	},
+	{
+		.name = "ENIO",
+		.pin = {
+			.label = "enio",
+			.gpio = AT91_PIN_PC15,
+			.flags =  GPIOF_OUT_INIT_LOW,
+		},
+	},
+	{
+		.name = "DEVICE_RESET",
+		.pin = {
+			.label = "reset",
+			.gpio = AT91_PIN_PA22,
+			.flags = GPIOF_IN,
+		},
+		.active_low = 1,
+	},
+	{
+		.name = "RSERSRC",
+		.pin = {
+			.label = "rsersrc",
+			.gpio = AT91_PIN_PC7,
+			.flags = GPIOF_OUT_INIT_HIGH,
+		},
+		.active_low = 1,
+	},
+	{
+		.name = "RADIO_RESET",
+		.pin = {
+			.label = "radio-reset",
+			.gpio = AT91_PIN_PB30,
+			.flags = GPIOF_OUT_INIT_HIGH,
+		},
+	},	
+	{
+		.name = "GPIO11",
+		.pin = {
+			.label = "gpio11",
+			.gpio = AT91_PIN_PB19,
+			.flags = GPIOF_OPEN_DRAIN | GPIOF_INIT_HIGH,
+		},
+	},	
+	{
+		.name = "GPIO12",
+		.pin = {
+			.label = "gpio12",
+			.gpio = AT91_PIN_PB20,
+			.flags = GPIOF_OPEN_DRAIN | GPIOF_INIT_HIGH,
+		},
+	},	
+	{
+		.name = "LED2",
+		.pin = {
+			.label = "led2",
+			.gpio = AT91_PIN_PA30,
+			.flags = GPIOF_OUT_INIT_HIGH,
+		},
+		.active_low = 1,
+	},	
+	{
+		.name = "LED3",
+		.pin = {
+			.label = "led3",
+			.gpio = AT91_PIN_PC9,
+#if LED_LS_CONTROLLABLE
+			.flags = GPIOF_OUT_INIT_HIGH,
+#else
+			.flags = GPIOF_IN,
+#endif
+		},
+		.active_low = 1,
+	},
+	/*
+	{
+		.name = "TXD1",
+		.pin = {
+			.gpio = AT91_PIN_PB17,
+			.flags = GPIOF_IN,
+		},
+	},*/
+	{ },
+};
+
+/* mt100eocg specific attributes */
+static DEVICE_ATTR_RO_MTS(dev_attr_extserial_dtr, "extserial-dtr",
+	mts_attr_show_gpio_pin);
+
+static DEVICE_ATTR_MTS(dev_attr_extserial_dcd_gpio, "extserial-dcd",
+	mts_attr_show_gpio_pin, mts_attr_store_gpio_pin);
+
+static DEVICE_ATTR_MTS(dev_attr_eth0_enabled, "eth0-enabled",
+	mts_attr_show_gpio_pin, mts_attr_store_gpio_pin);
+
+static DEVICE_ATTR_MTS(dev_attr_enio, "enio",
+	mts_attr_show_gpio_pin, mts_attr_store_gpio_pin);
+
+static DEVICE_ATTR_MTS(dev_attr_gpo1, "gpo1",
+	mts_attr_show_dout, mts_attr_store_dout);
+static DEVICE_ATTR_MTS(dev_attr_gpo2, "gpo2",
+	mts_attr_show_dout, mts_attr_store_dout);
+static DEVICE_ATTR_MTS(dev_attr_gpo3, "gpo3",
+	mts_attr_show_dout, mts_attr_store_dout);
+static DEVICE_ATTR_MTS(dev_attr_gpo4, "gpo4",
+	mts_attr_show_dout, mts_attr_store_dout);
+
+
+static DEVICE_ATTR_MTS(dev_attr_led1, "led1",
+	mts_attr_show_dout, mts_attr_store_dout);
+static DEVICE_ATTR_MTS(dev_attr_led2, "led2",
+	mts_attr_show_gpio_pin, mts_attr_store_gpio_pin);
+
+#if LED_LS_CONTROLLABLE
+static DEVICE_ATTR_MTS(dev_attr_led3, "led3",
+	mts_attr_show_gpio_pin, mts_attr_store_gpio_pin);
+#else
+static DEVICE_ATTR_RO_MTS(dev_attr_led3, "led3", mts_attr_show_gpio_pin);
+#endif
+
+static DEVICE_ATTR_MTS(dev_attr_led4, "led4",
+	mts_attr_show_dout, mts_attr_store_dout);
+static DEVICE_ATTR_MTS(dev_attr_led5, "led5",
+	mts_attr_show_dout, mts_attr_store_dout);
+static DEVICE_ATTR_MTS(dev_attr_led6, "led6",
+	mts_attr_show_dout, mts_attr_store_dout);
+
+static DEVICE_ATTR_MTS(dev_attr_gpio11, "gpio11",
+	mts_attr_show_gpio_pin, mts_attr_store_gpio_pin);
+static DEVICE_ATTR_MTS(dev_attr_gpio12, "gpio12",
+	mts_attr_show_gpio_pin, mts_attr_store_gpio_pin);
+
+static DEVICE_ATTR_MTS(dev_attr_rsersrc, "rsersrc",
+	mts_attr_show_gpio_pin, mts_attr_store_gpio_pin);
+
+static struct attribute *mt100eocg_platform_attributes[] = {
+	&dev_attr_vendor_id.attr,
+	&dev_attr_product_id.attr,
+	&dev_attr_device_id.attr,
+	&dev_attr_hw_version.attr,
+	&dev_attr_imei.attr,
+	&dev_attr_eth_mac.attr,
+	&dev_attr_has_radio.attr,
+	&dev_attr_reset.attr,
+	&dev_attr_reset_monitor.attr,
+	&dev_attr_reset_monitor_intervals.attr,
+	&dev_attr_extserial_dtr.attr,
+	&dev_attr_extserial_dcd_gpio.attr,
+	&dev_attr_rsersrc.attr,  // AT91_PIN_PC7
+	&dev_attr_radio_reset.attr, // AT91_PIN_PB30
+	&dev_attr_eth0_enabled.attr,
+	&dev_attr_gpio11.attr, // AT91_PIN_PB19
+	&dev_attr_gpio12.attr, // AT91_PIN_PB20
+	&dev_attr_enio.attr,
+// SPI
+	&dev_attr_gpo1.attr, 
+	&dev_attr_gpo2.attr,
+	&dev_attr_gpo3.attr,
+	&dev_attr_gpo4.attr,
+//
+// SPI
+	&dev_attr_led1.attr,
+//
+	&dev_attr_led2.attr, // AT91_PIN_PA30
+	&dev_attr_led3.attr, // AT91_PIN_PC9
+// SPI
+	&dev_attr_led4.attr,
+	&dev_attr_led5.attr,
+	&dev_attr_led6.attr,
+//
+// SPI
+	&dev_attr_gpi5.attr,
+	&dev_attr_gpi6.attr,
+	&dev_attr_gpi7.attr,
+	&dev_attr_gpi8.attr,
+	&dev_attr_gpi9.attr,
+	&dev_attr_gpi10.attr,
+//
+// SPI
+	&dev_attr_board_temperature.attr,
+//
+// adc
+	&dev_attr_adc0.attr,
+	&dev_attr_adc1.attr,
+	&dev_attr_adc2.attr,
+	&dev_attr_adc3.attr,
+
+	NULL,
+};
+
+static struct attribute_group mt100eocg_platform_attribute_group = {
+	.attrs = mt100eocg_platform_attributes
+};
diff --git a/io-module/machine/mtcap.c b/io-module/machine/mtcap.c
new file mode 100644
index 0000000..bd08d5a
--- /dev/null
+++ b/io-module/machine/mtcap.c
@@ -0,0 +1,536 @@
+#include "at91gpio.h"
+/* Used for both MTCAP 0.0 and 0.1 */
+static struct gpio_pin gpio_pins_mtcap_0_0[] = {
+	{
+		.name = "ETH_RESET",
+		.pin = {
+			.gpio = AT91_PIN_PC6, // NETH_RST
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "eth-reset",
+		},
+	},
+	{
+		.name = "RADIO_POWER_MONITOR",
+		.pin = {
+			.gpio = AT91_PIN_PD21, // PWRMON
+			.flags = GPIOF_IN,
+			.label = "radio-power-monitor",
+		},
+	},
+	{
+		.name = "RADIO_RESET",
+		.pin = {
+			.gpio = AT91_PIN_PA22, // 3G_RST
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "radio-reset",
+		},
+	},
+	{
+		.name = "RADIO_POWER",
+		.pin = {
+			.gpio = AT91_PIN_PA21, // 3G_ONOFF
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "radio-power",
+		},
+	},
+	{
+		.name = "DEVICE_RESET",
+		.pin = {
+			.gpio = AT91_PIN_PC4, // OPT_RST
+			.flags = GPIOF_IN,
+			.label = "reset",
+		},
+		.active_low = 1,
+	},
+	{
+		.name = "LORA_RESET",
+		.pin = {
+			.gpio = AT91_PIN_PA8, // LORA_RST
+			.flags = GPIOF_OUT_INIT_LOW,
+			.label = "lora/reset",
+		},
+		.capability = CAPA_LORA,
+		.active_low = 1,
+	},
+	{  // gpio 1 for LORA 1.5 ref design
+		.name = "LORA_CDONE",
+		.pin = {
+			.gpio = AT91_PIN_PA6,
+			.flags = GPIOF_IN,
+			.label = "lora/cdone",
+		},
+		.capability = CAPA_LORA,
+	},
+	{  // gpio 2 for LORA 1.5 ref design
+		.name = "LORA_CRESET",
+		.pin = {
+			.gpio = AT91_PIN_PA29,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "lora/creset",
+		},
+		.capability = CAPA_LORA,
+	},
+
+
+	/* LEDs */
+	{
+		.name = "STATUS_LED", // DEV_LED_GN
+		.pin = {
+			.gpio = AT91_PIN_PC25,
+			.flags = GPIOF_OUT_INIT_LOW,
+			.label = "led-status",
+		},
+		.active_low = 1,
+	},
+	{
+		.name = "LED2", // LED2 is for LoRa status
+		.pin = {
+			.gpio = AT91_PIN_PC15,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "led-lora",
+		},
+		.active_low = 1,
+	},
+	{
+		.name = "LED3", // LED3 is for Cellular status (Modem can directly enable it)
+		.pin = {
+			.gpio = AT91_PIN_PC16,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "led-cd",
+		},
+		.active_low = 1,
+	},
+	{
+		.name = "LED4", // LED4 is for WiFi status
+		.pin = {
+			.gpio = AT91_PIN_PC20,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "led-wifi",
+		},
+		.active_low = 1,
+	},
+	{
+		.name = "WLAN_EN",
+		.pin = {
+			.gpio = AT91_PIN_PA4,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "wlan-en",
+		},
+	},
+	{
+		.name = "WLAN_RST",
+		.pin = {
+			.gpio = AT91_PIN_PA3,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "wlan-rst",
+		},
+	},
+	{ },
+};
+
+static int radio_unconditional_shutdown_mtcap(void)
+{
+	struct gpio_pin *rst_pin = gpio_pin_by_attr_name("radio-reset");
+	struct gpio_pin *pwrmon_pin = gpio_pin_by_attr_name("radio-power-monitor");
+	int value;
+	int i;
+
+	if (!rst_pin || !pwrmon_pin) {
+		return -ENODEV;
+	}
+
+	// To unconditionally shutdown the LE910, the pad HW_SHUTDOWN* must
+	// be tied low for at least 200 milliseconds and then released.
+	reset_gpio_pin(rst_pin, 500, 0);
+
+	msleep(100);
+
+	// Wait for the power off
+	for (i = 0; i < 5; i++) {
+		value = gpio_get_value(pwrmon_pin->pin.gpio);
+		if (value != 0) {
+			log_warning("radio is still on.");
+			msleep(500);
+			continue;
+		}
+		log_warning("radio has been shutdown unconditionally");
+		break;
+	}
+
+	return 0;
+}
+
+
+/* radio control (power/reset) for mtcap */
+static int radio_off_mtcap(int radio_model)
+{
+	// ref: Telit_LE910_Hardware_User_Guide_r6.pdf (4.3.2 Hardware Shutdown)
+	struct gpio_pin *pwrmon_pin = gpio_pin_by_attr_name("radio-power-monitor");
+	struct gpio_pin *onoff_pin = gpio_pin_by_attr_name("radio-power");
+	struct gpio_pin *rst_pin = gpio_pin_by_attr_name("radio-reset");
+	unsigned int hold_time;
+	int value;
+	int i;
+
+	if (!onoff_pin || !pwrmon_pin || !rst_pin) {
+		return -ENODEV;
+	}
+
+	value = gpio_get_value(pwrmon_pin->pin.gpio);
+	if(value == 0) {
+		log_warning("cell radio is already off");
+		return 0;
+	}
+
+	log_info("turning off cell radio");
+
+	// To turn OFF LE910 the pad ON/OFF# must be tied low for at least 2 seconds and then
+	// released. Same circuitry and timing for the power on must be used. When the hold
+	// time of ON/OFF# is above 2 seconds, LE910 goes into the finalization state and
+	// finally will shut down PWRMON at the end of this state. The period of the
+	// finalization state can differ according to the situation in which the LE910 is so it
+	// cannot be fixed definitely. Normally it will be above 15 seconds later from releasing
+	// ON/OFF# and DTE should monitor the status of PWRMON to see the actual power off.
+	hold_time = 2500;
+	if (radio_model == RADIO_LNA3 || radio_model == RADIO_LEU3) {
+		
+		// To turn OFF the LE910 V2 the pad ON_OFF* must be tied low for at least 3 seconds and then released.
+		// ref: Telit_LE910_V2_Hardware_User_Guide_r7.pdf
+		hold_time = 3500;
+	}
+
+	reset_gpio_pin(onoff_pin, hold_time, 0);
+	msleep(200);  // Give time for pin to change state before inspection.
+
+	value = 0;
+	for (i = 0; i < 15; i++) {
+		// check that power is low
+		value = gpio_get_value(pwrmon_pin->pin.gpio);
+		if (value != 0) {
+			log_info("cell radio is still on. keep waiting...");
+			msleep(2000);
+			continue;
+		}
+		break;
+	}
+
+	if (value == 0) {
+		log_info("cell radio has been shut down");
+	}
+	else {
+		log_warning("cell radio is still on. performing unconditional shutdown...");
+		radio_unconditional_shutdown_mtcap();
+	}
+
+	return 0;
+}
+
+static int radio_on_mtcap(int radio_model)
+{
+	// ref: Telit_LE910_Hardware_User_Guide_r6.pdf
+	struct gpio_pin *pwrmon_pin = gpio_pin_by_attr_name("radio-power-monitor");
+	struct gpio_pin *onoff_pin = gpio_pin_by_attr_name("radio-power");
+	struct gpio_pin *rst_pin = gpio_pin_by_attr_name("radio-reset");
+	unsigned int hold_time;
+	int value;
+
+	if (!onoff_pin || !pwrmon_pin || !rst_pin) {
+		return -ENODEV;
+	}
+
+	value = gpio_get_value(pwrmon_pin->pin.gpio);
+	if(value != 0) {
+		log_warning("cell radio is already on");
+		return 0;
+	}
+
+	log_info("turning on cell radio");
+
+	// for LEU1 (ref: Telit_LE910_Hardware_User_Guide_r6.pdf)
+	hold_time = 1500;
+	if (radio_model == RADIO_LNA3 || radio_model == RADIO_LEU3) {
+		
+		// To turn on the LE910 V2 the pad ON_OFF* must be tied low for at least 5 seconds and then released.
+		// ref: Telit_LE910_V2_Hardware_User_Guide_r7.pdf
+		// ref:Telit_LE910_V2_Hardware_User_Guide_r9.pdf
+		//    pg 32: When USB is connected or after firmware updating,
+		//    delay must be equal at least to 10 seconds.
+		hold_time = 10500;
+	}
+
+	// drive on/off pin high for at least 1 seconoff_pin
+	gpio_set_value(onoff_pin->pin.gpio, 1);
+	msleep(1000);
+
+	// ON_OFF must be tied low and then released
+	reset_gpio_pin(onoff_pin, hold_time, 0);
+	msleep(200);  // Make sure modem has had time to move the status pin
+	// check that power is high
+	value = gpio_get_value(pwrmon_pin->pin.gpio);
+	if(value == 0) {
+		log_warning("cell radio is still off.");
+	} else {
+		log_info("cell radio has been turned on");
+	}
+
+	return 0;
+}
+
+static int radio_reset_mtcap(int radio_model)
+{
+	// ref: Telit_LE910_Hardware_User_Guide_r6.pdf
+	struct gpio_pin *rst_pin = gpio_pin_by_attr_name("radio-reset");
+	struct gpio_pin *onoff_pin = gpio_pin_by_attr_name("radio-power");
+	unsigned int hold_time;
+
+	if (!rst_pin || !onoff_pin)  {
+		return -ENODEV;
+	}
+
+	//
+	// Unconditional shutdown
+	//
+
+	log_info("performing unconditional cell radio shutdown");
+
+	radio_unconditional_shutdown_mtcap();
+
+	//
+	// Turning on radio
+	//
+	log_info("turning on cell radio for reset");
+
+	// for LEU1 (ref: Telit_LE910_Hardware_User_Guide_r6.pdf)
+	hold_time = 1500;
+	if (radio_model == RADIO_LNA3 || radio_model == RADIO_LEU3) {
+		// To turn on the LE910 V2 the pad ON_OFF* must be tied low for at least 5 seconds and then released.
+		// ref: Telit_LE910_V2_Hardware_User_Guide_r7.pdf
+		// ref:Telit_LE910_V2_Hardware_User_Guide_r9.pdf
+		//    pg 32: When USB is connected or after firmware updating,
+		//    delay must be equal at least to 10 seconds.
+                //
+                // Note that a hold time of 5.5 seconds on MTCAP
+                // with Verizon Firmware 20.00.12 will cause a
+                // radio-reset to power the LE910-NA1 off until
+                // a reload of the mts-io driver, or a reboot.
+		hold_time = 10500;
+	}
+
+	// drive on/off pin high for at least 1 sec
+	gpio_set_value(onoff_pin->pin.gpio, 1);
+	msleep(1000);
+
+
+	// drive on/off pin low for < 2 sec
+	// drive on/off pin high
+	log_info("turning off cell radio for reset");
+	reset_gpio_pin(onoff_pin, hold_time, 0);
+	log_info("Reset is complete.  Wait for power monitor pin");
+	msleep(200);  // Make sure modem has had time to move the status pin
+	return 0;
+}
+
+static ssize_t mts_attr_store_radio_power_mtcap(struct device *dev,
+		struct device_attribute *attr, const char *buf, size_t count)
+{
+	int value;
+	int err;
+	int radio_model = get_radio_model_from_product_id();
+
+	if (sscanf(buf, "%i", &value) != 1) {
+		return -EINVAL;
+	}
+
+	mutex_lock(&mts_io_mutex);
+	if (value == 0) {
+		err = radio_off_mtcap(radio_model);
+	} else {
+		err = radio_on_mtcap(radio_model);
+	}
+	mutex_unlock(&mts_io_mutex);
+
+	if (err) {
+		return err;
+	}
+
+	return count;
+}
+
+static ssize_t mts_attr_store_radio_reset_mtcap(struct device *dev,
+		struct device_attribute *attr, const char *buf, size_t count)
+{
+	int value; /* 0 = normal reset; -1 = forced reset */
+	int err;
+	int radio_model = get_radio_model_from_product_id();
+
+	if (sscanf(buf, "%i", &value) != 1) {
+		return -EINVAL;
+	}
+
+	if (value != 0 && value != -1) {
+		return -EINVAL;
+	}
+
+	/* check reset timings is enabled */
+	if (value != -1 && NULL != timings_data) {
+		/* check reset timer is started */
+		if (radio_reset_timer_is_start == 1) {
+			log_info("cell radio reset timer is running. \n");
+			return count;
+		}
+
+		/* check reset timer available is started */
+		if (radio_reset_available_timer_is_start == 1) {
+			del_timer(&radio_reset_available_timer);
+			radio_reset_available_timer_is_start = 0;
+		}
+
+		/* reset timer not started, start it */
+		mod_timer(&radio_reset_timer, jiffies + msecs_to_jiffies((timings_data[timings_data_index]) * 1000));
+		//log_info("radio reset timer is start = [%d]\n", time_now_secs());
+		/* save timings_data_stop_seconds */
+		timings_data_stop_seconds = timings_data[timings_data_index] + time_now_secs();
+		radio_reset_timer_is_start = 1;
+	}
+
+	mutex_lock(&mts_io_mutex);
+
+	err = radio_reset_mtcap(radio_model);
+
+	mutex_unlock(&mts_io_mutex);
+
+	if (err) {
+		return err;
+	}
+
+	return count;
+}
+
+static ssize_t mts_attr_show_radio_power_mtcap(struct device *dev,
+			struct device_attribute *attr,
+			char *buf)
+{
+	int value;
+	struct gpio_pin *pwrmon_pin = gpio_pin_by_attr_name("radio-power-monitor");
+
+	if ( !pwrmon_pin ) {
+		return -ENODEV;
+	}
+
+	value = gpio_get_value(pwrmon_pin->pin.gpio);
+	return sprintf(buf, "%d\n", value);
+}
+
+static DEVICE_ATTR_MTS(dev_attr_radio_reset_mtcap, "radio-reset",
+		mts_attr_show_gpio_pin, mts_attr_store_radio_reset_mtcap);
+
+static DEVICE_ATTR_MTS(dev_attr_radio_power_mtcap, "radio-power",
+		mts_attr_show_radio_power_mtcap, mts_attr_store_radio_power_mtcap);
+
+static DEVICE_ATTR_MTS(dev_attr_eth_reset_mtcap, "eth-reset",
+		mts_attr_show_gpio_pin, mts_attr_store_gpio_pin);
+
+static DEVICE_ATTR_MTS(dev_attr_led_lora_gpio_mtcap, "led-lora",
+		mts_attr_show_gpio_pin, mts_attr_store_gpio_pin);
+
+static DEVICE_ATTR_MTS(dev_attr_led_wifi_gpio_mtcap, "led-wifi",
+		mts_attr_show_gpio_pin, mts_attr_store_gpio_pin);
+
+static DEVICE_ATTR_MTS(dev_attr_wlan_en_gpio_mtcap, "wlan-en",
+		mts_attr_show_gpio_pin, mts_attr_store_gpio_pin);
+
+static DEVICE_ATTR_MTS(dev_attr_wlan_rst_gpio_mtcap, "wlan-rst",
+		mts_attr_show_gpio_pin, mts_attr_store_gpio_pin);
+
+static struct attribute *mtcap_0_0_platform_attributes[] = {
+		&dev_attr_vendor_id.attr,
+		&dev_attr_product_id.attr,
+		&dev_attr_device_id.attr,
+		&dev_attr_uuid.attr,
+		&dev_attr_hw_version.attr,
+		&dev_attr_imei.attr,
+		&dev_attr_eth_mac.attr,
+		&dev_attr_has_radio.attr,
+		&dev_attr_reset.attr,
+		&dev_attr_reset_monitor.attr,
+		&dev_attr_reset_monitor_intervals.attr,
+
+		&dev_attr_eth_reset_mtcap.attr,
+		&dev_attr_led_status.attr,
+		&dev_attr_led_cd_gpio.attr,
+		&dev_attr_led_lora_gpio_mtcap.attr,
+		&dev_attr_led_wifi_gpio_mtcap.attr,
+
+		&dev_attr_wlan_en_gpio_mtcap.attr,
+		&dev_attr_wlan_rst_gpio_mtcap.attr,
+
+		/* Set to NULL if no radio -- should be 1st radio attribute */
+		&dev_attr_radio_power_mtcap.attr,
+		&dev_attr_radio_reset_mtcap.attr,
+
+		&dev_attr_radio_reset_backoffs.attr,
+		&dev_attr_radio_reset_backoff_index.attr,
+		&dev_attr_radio_reset_backoff_seconds.attr,
+
+		NULL,
+};
+
+static int 
+is_radio_power_attr_mtcap(struct attribute *attr)
+{
+    return (attr ==  &dev_attr_radio_power_mtcap.attr);
+}
+
+static struct attribute_group mtcap_0_0_platform_attribute_group = {
+	.attrs = mtcap_0_0_platform_attributes
+};
+
+
+//
+// on-board LORA attributes are to be stored in the lora/ sub-directory
+//
+//
+static DEVICE_ATTR_MTS(dev_attr_lora_reset_mtcap, "reset",
+		mts_attr_show_lora_gpio_pin, mts_attr_store_lora_gpio_pin);
+
+static DEVICE_ATTR_RO_MTS(dev_attr_lora_cdone_mtcap, "cdone",
+		mts_attr_show_lora_gpio_pin);
+
+static DEVICE_ATTR_MTS(dev_attr_lora_creset_mtcap, "creset",
+		mts_attr_show_lora_gpio_pin, mts_attr_store_lora_gpio_pin);
+
+static DEVICE_ATTR_RO_MTS(dev_attr_lora_eui_mtcap, "eui",
+		mts_attr_show_lora_product_info);
+
+static DEVICE_ATTR_RO_MTS(dev_attr_lora_product_id_mtcap, "product-id",
+		mts_attr_show_lora_product_info);
+
+static DEVICE_ATTR_RO_MTS(dev_attr_lora_hw_version_mtcap, "hw-version",
+		mts_attr_show_lora_product_info);
+
+static struct attribute *mtcap_0_0_lora_attributes[] = {
+		&dev_attr_lora_eui_mtcap.attr,
+		&dev_attr_lora_product_id_mtcap.attr,
+		&dev_attr_lora_hw_version_mtcap.attr,
+		&dev_attr_lora_reset_mtcap.attr,
+		&dev_attr_lora_cdone_mtcap.attr,
+		&dev_attr_lora_creset_mtcap.attr,
+		NULL,
+};
+
+static struct attribute_group mtcap_0_0_lora_attribute_group = {
+	.attrs = mtcap_0_0_lora_attributes
+};
+
+// Reset for LoRa firmware is done using the I2C bus
+// on the MTCDTIPHP LoRa board.
+static struct attribute *mtcdtiphp_0_0_lora_attributes[] = {
+		&dev_attr_lora_eui_mtcap.attr,
+		&dev_attr_lora_product_id_mtcap.attr,
+		&dev_attr_lora_hw_version_mtcap.attr,
+		NULL,
+};
+
+static struct attribute_group mtcdtiphp_0_0_lora_attribute_group = {
+	.attrs = mtcdtiphp_0_0_lora_attributes
+};
diff --git a/io-module/machine/mtcdt.c b/io-module/machine/mtcdt.c
new file mode 100644
index 0000000..575dd1e
--- /dev/null
+++ b/io-module/machine/mtcdt.c
@@ -0,0 +1,481 @@
+#include "at91gpio.h"
+/*
+ * Within a struct gpio_pin, there is only one
+ * occurrence of each pin, so there is only one
+ * pin label set for each gpio pin.
+ */
+static struct gpio_pin gpio_pins_mtcdt_0_0[] = {
+	{
+		.name = "RADIO_RESET",
+		.pin = {
+			.gpio = AT91_PIN_PC3,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "radio-reset",
+		},
+	},
+	{
+		.name = "RADIO_RESET",
+		.pin = {
+			.gpio = AT91_PIN_PC3,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "radio-power",
+		},
+	},
+	{
+		.name = "DEVICE_RESET",
+		.pin = {
+			.gpio = AT91_PIN_PC2,
+			.flags = GPIOF_IN,
+			.label = "reset",
+		},
+		.active_low = 1,
+	},
+	{
+		.name = "ETH_RESET",
+		.pin = {
+				.gpio = AT91_PIN_PC4,
+				.flags = GPIOF_OUT_INIT_HIGH,
+				.label = "eth-reset",
+		}
+	},
+	{
+		.name = "LS_LED", /* LED7 */
+		.pin = {
+			.gpio = AT91_PIN_PA14,
+#if LED_LS_CONTROLLABLE
+			.flags = GPIOF_OUT_INIT_HIGH,
+#else
+			.flags = GPIOF_IN,
+#endif
+			.label = "led-ls",
+		},
+		.active_low = 1,
+	},
+	{
+		.name = "STATUS_LED", /* LED2 */
+		.pin = {
+			.gpio = AT91_PIN_PA24,
+			.flags = GPIOF_OUT_INIT_LOW,
+			.label = "led-status",
+		},
+		.active_low = 1,
+	},
+	{
+		.name = "LED5",
+		.pin = {
+			.gpio = AT91_PIN_PA25,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "led-cd",
+		},
+		.active_low = 1,
+	},
+	{
+		.name = "LED5",
+		.pin = {
+			.gpio = AT91_PIN_PA25,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "led-a",
+		},
+		.active_low = 1,
+	},
+	{
+		.name = "LED1",
+		.pin = {
+			.gpio = AT91_PIN_PA26,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "led-sig1",
+		},
+		.active_low = 1,
+	},
+	{
+		.name = "LED1",
+		.pin = {
+			.gpio = AT91_PIN_PA26,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "led-b",
+		},
+		.active_low = 1,
+	},
+	{
+		.name = "LED4",
+		.pin = {
+			.gpio = AT91_PIN_PA27,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "led-sig2",
+		},
+		.active_low = 1,
+	},
+	{
+		.name = "LED4",
+		.pin = {
+			.gpio = AT91_PIN_PA27,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "led-c",
+		},
+		.active_low = 1,
+	},
+	{
+		.name = "LED3",
+		.pin = {
+			.gpio = AT91_PIN_PA28,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "led-sig3",
+		},
+		.active_low = 1,
+	},
+	{
+		.name = "LED3",
+		.pin = {
+			.gpio = AT91_PIN_PA28,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "led-d",
+		},
+		.active_low = 1,
+	},
+};
+
+static struct gpio_pin gpio_pins_mtcdt_0_1[] = {
+	{
+		.name = "RADIO_RESET",
+		.pin = {
+			.gpio = AT91_PIN_PC3,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "radio-reset",
+		},
+	},
+	{
+		.name = "RADIO_RESET",
+		.pin = {
+			.gpio = AT91_PIN_PC3,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "radio-power",
+		},
+	},
+	{
+		.name = "DEVICE_RESET",
+		.pin = {
+			.gpio = AT91_PIN_PC2,
+			.flags = GPIOF_IN,
+			.label = "reset",
+		},
+		.active_low = 1,
+	},
+	{
+		.name = "LS_LED", /* LED7 */
+		.pin = {
+			.gpio = AT91_PIN_PA14,
+#if LED_LS_CONTROLLABLE
+			.flags = GPIOF_OUT_INIT_HIGH,
+#else
+			.flags = GPIOF_IN,
+#endif
+			.label = "led-ls",
+		},
+		.active_low = 1,
+	},
+	{
+		.name = "STATUS_LED", /* LED2 */
+		.pin = {
+			.gpio = AT91_PIN_PA24,
+			.flags = GPIOF_OUT_INIT_LOW,
+			.label = "led-status",
+		},
+		.active_low = 1,
+	},
+	{
+		.name = "LED5",
+		.pin = {
+			.gpio = AT91_PIN_PA25,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "led-cd",
+		},
+		.active_low = 1,
+	},
+	{
+		.name = "LED5",
+		.pin = {
+			.gpio = AT91_PIN_PA25,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "led-a",
+		},
+		.active_low = 1,
+	},
+	{
+		.name = "LED1",
+		.pin = {
+			.gpio = AT91_PIN_PA26,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "led-sig1",
+		},
+		.active_low = 1,
+	},
+	{
+		.name = "LED1",
+		.pin = {
+			.gpio = AT91_PIN_PA26,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "led-b",
+		},
+		.active_low = 1,
+	},
+	{
+		.name = "LED4",
+		.pin = {
+			.gpio = AT91_PIN_PA27,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "led-sig2",
+		},
+		.active_low = 1,
+	},
+	{
+		.name = "LED4",
+		.pin = {
+			.gpio = AT91_PIN_PA27,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "led-c",
+		},
+		.active_low = 1,
+	},
+	{
+		.name = "LED3",
+		.pin = {
+			.gpio = AT91_PIN_PA28,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "led-sig3",
+		},
+		.active_low = 1,
+	},
+	{
+		.name = "LED3",
+		.pin = {
+			.gpio = AT91_PIN_PA28,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "led-d",
+		},
+		.active_low = 1,
+	},
+	{
+		.name = "ETH_RESET",
+		.pin = {
+				.gpio = AT91_PIN_PC4,
+				.flags = GPIOF_OUT_INIT_HIGH,
+				.label = "eth-reset",
+		}
+	},
+	{
+		.name = "WIFI_BT_ULPWKUP",
+		.pin = {
+			.gpio = AT91_PIN_PA0,
+			.flags = GPIOF_IN,
+			.label = "wifi-bt-ulpwkup",
+		},
+		.capability = CAPA_WIFI,
+	},
+	{
+		.name = "WIFI_BT_LPWKUP",
+		.pin = {
+			.gpio = AT91_PIN_PA6,
+			.flags = GPIOF_IN,
+			.label = "wifi-bt-lpwkup",
+		},
+		.capability = CAPA_WIFI,
+	},
+	{
+		.name = "WIFI_BT_INT",
+		.pin = {
+			.gpio = AT91_PIN_PB11,
+			.flags = GPIOF_IN,
+			.label = "wifi-bt-int",
+		},
+		.capability = CAPA_WIFI,
+	},
+	{
+		.name = "WIFI_BT_RESET",
+		.pin = {
+			.gpio = AT91_PIN_PD14,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "wifi-bt-reset",
+		},
+		.capability = CAPA_WIFI,
+	},
+	{
+		.name = "GNSS_RESET",
+		.pin = {
+			.gpio = AT91_PIN_PD15,
+			.flags = GPIOF_OUT_INIT_LOW, /* Keep GPS quiet during boot for EXAR */
+			.label = "gnss-reset",
+		},
+		.capability = CAPA_GPS,
+	},
+	{
+		.name = "SECURE_RESET",
+		.pin = {
+			.gpio = AT91_PIN_PD16,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "secure-reset",
+		}
+	},
+	{
+		.name = "MTQ_RESET",
+		.pin = {
+			.gpio = AT91_PIN_PD17,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "mtq-reset",
+		}
+	},
+	{
+		.name = "USBHUB_RESET",
+		.pin = {
+			.gpio = AT91_PIN_PD18,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "usbhub-reset",
+		}
+	},
+	{
+		.name = "GNSS_INT",
+		.pin = {
+			.gpio = AT91_PIN_PD19,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "gnss-int",
+		},
+		.capability = CAPA_GPS,
+	},
+	{
+		.name = "WIFI_BT_LPMODE",
+		.pin = {
+			.gpio = AT91_PIN_PD20,
+			.flags = GPIOF_IN,
+			.label = "wifi-bt-lpmode",
+		},
+		.capability = CAPA_WIFI,
+	},
+	{ },
+};
+
+static DEVICE_ATTR_MTS(dev_attr_wifi_bt_lpwkup, "wifi-bt-lpwkup",
+	mts_attr_show_gpio_pin, mts_attr_store_gpio_pin);
+static DEVICE_ATTR_MTS(dev_attr_wifi_bt_ulpwkup, "wifi-bt-ulpwkup",
+	mts_attr_show_gpio_pin, mts_attr_store_gpio_pin);
+static DEVICE_ATTR_MTS(dev_attr_wifi_bt_reset, "wifi-bt-reset",
+	mts_attr_show_gpio_pin, mts_attr_store_gpio_pin);
+static DEVICE_ATTR_RO_MTS(dev_attr_wifi_bt_lpmode, "wifi-bt-lpmode",
+	mts_attr_show_gpio_pin);
+static DEVICE_ATTR_RO_MTS(dev_attr_wifi_bt_int, "wifi-bt-int",
+	mts_attr_show_gpio_pin);
+static DEVICE_ATTR_MTS(dev_attr_gnss_reset, "gnss-reset",
+	mts_attr_show_gpio_pin, mts_attr_store_gpio_pin);
+static DEVICE_ATTR_MTS(dev_attr_usbhub_reset, "usbhub-reset",
+	mts_attr_show_gpio_pin, mts_attr_store_gpio_pin);
+static DEVICE_ATTR_MTS(dev_attr_eth_reset, "eth-reset",
+	mts_attr_show_gpio_pin, mts_attr_store_gpio_pin);
+static DEVICE_ATTR_MTS(dev_attr_gnss_int, "gnss-int",
+	mts_attr_show_gpio_pin, mts_attr_store_gpio_pin);
+static DEVICE_ATTR_RO_MTS(dev_attr_wifi_mac, "mac-wifi",
+	mts_attr_show_product_info);
+static DEVICE_ATTR_RO_MTS(dev_attr_bluetooth_mac, "mac-bluetooth",
+	mts_attr_show_product_info);
+
+static struct attribute *mtcdt_platform_attributes[] = {
+	&dev_attr_vendor_id.attr,
+	&dev_attr_product_id.attr,
+	&dev_attr_device_id.attr,
+	&dev_attr_uuid.attr,
+	&dev_attr_hw_version.attr,
+	&dev_attr_imei.attr,
+	&dev_attr_eth_mac.attr,
+	&dev_attr_has_radio.attr,
+	&dev_attr_reset.attr,
+	&dev_attr_reset_monitor.attr,
+	&dev_attr_reset_monitor_intervals.attr,
+
+	&dev_attr_led_status.attr,
+	&dev_attr_led_cd_gpio.attr,
+	&dev_attr_led_sig1_gpio.attr,
+	&dev_attr_led_sig2_gpio.attr,
+	&dev_attr_led_sig3_gpio.attr,
+
+	&dev_attr_led_a_gpio.attr,
+	&dev_attr_led_b_gpio.attr,
+	&dev_attr_led_c_gpio.attr,
+	&dev_attr_led_d_gpio.attr,
+	&dev_attr_eth_reset.attr,
+
+        &dev_attr_radio_power.attr,
+	&dev_attr_radio_reset.attr,
+
+	&dev_attr_radio_reset_backoffs.attr,
+	&dev_attr_radio_reset_backoff_index.attr,
+	&dev_attr_radio_reset_backoff_seconds.attr,
+	NULL,
+};
+
+static struct attribute *mtcdt_0_1_platform_attributes[] = {
+	&dev_attr_vendor_id.attr,
+	&dev_attr_product_id.attr,
+	&dev_attr_device_id.attr,
+	&dev_attr_uuid.attr,
+	&dev_attr_hw_version.attr,
+	&dev_attr_imei.attr,
+	&dev_attr_eth_mac.attr,
+	&dev_attr_has_radio.attr,
+	&dev_attr_reset.attr,
+	&dev_attr_reset_monitor.attr,
+	&dev_attr_reset_monitor_intervals.attr,
+
+	&dev_attr_led_status.attr,
+	&dev_attr_led_cd_gpio.attr,
+	&dev_attr_led_sig1_gpio.attr,
+	&dev_attr_led_sig2_gpio.attr,
+	&dev_attr_led_sig3_gpio.attr,
+
+	&dev_attr_led_a_gpio.attr,
+	&dev_attr_led_b_gpio.attr,
+	&dev_attr_led_c_gpio.attr,
+	&dev_attr_led_d_gpio.attr,
+
+	&dev_attr_usbhub_reset.attr,
+	&dev_attr_eth_reset.attr,
+        
+        // radio feature is last to be able to 
+        // easily remove radio.
+        // is_radio_power_attr_mtcdt() searches
+        // for this for truncation.
+        &dev_attr_radio_power.attr,  /* Must be first radio attribute */
+	&dev_attr_radio_reset.attr,
+
+	&dev_attr_radio_reset_backoffs.attr,
+	&dev_attr_radio_reset_backoff_index.attr,
+	&dev_attr_radio_reset_backoff_seconds.attr,
+
+	NULL,
+};
+
+static struct attribute *mtcdt_0_1_wifi_bt_attributes[] = {
+		&dev_attr_wifi_bt_lpwkup.attr,
+		&dev_attr_wifi_bt_ulpwkup.attr,
+		&dev_attr_wifi_bt_reset.attr,
+		&dev_attr_wifi_bt_lpmode.attr,
+		&dev_attr_wifi_bt_int.attr,
+                &dev_attr_bluetooth_mac.attr,
+                &dev_attr_wifi_mac.attr,
+};
+
+static struct attribute *mtcdt_0_1_gnss_attributes[] = {
+		&dev_attr_gnss_reset.attr,
+		&dev_attr_gnss_int.attr,
+};
+
+
+static struct attribute_group mtcdt_platform_attribute_group = {
+	.attrs = mtcdt_platform_attributes
+};
+static struct attribute_group mtcdt_0_1_platform_attribute_group = {
+	.attrs = mtcdt_0_1_platform_attributes
+};
+
+
+static int 
+is_radio_power_attr_mtcdt(struct attribute *attr)
+{
+    return (attr ==  &dev_attr_radio_power.attr);
+}
diff --git a/io-module/machine/mtcpm.c b/io-module/machine/mtcpm.c
new file mode 100644
index 0000000..8167218
--- /dev/null
+++ b/io-module/machine/mtcpm.c
@@ -0,0 +1,297 @@
+#include "mts_io.h"
+
+#define OMAP_GPIO(BANK, GPIO) ((BANK*32)+GPIO)
+/*
+ * Within a struct gpio_pin, there is only one
+ * occurrence of each pin, so there is only one
+ * pin label set for each gpio pin.
+ */
+static struct gpio_pin gpio_pins_mtcpm[] = {
+	{
+		.name = "RADIO_RESET",
+		.pin = {
+			.gpio = OMAP_GPIO(5,9), /* 5_9 */
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "radio-reset",
+		},
+	},
+#if 0
+  /* This goes through the PMIC for now */
+	{
+		.name = "RADIO_POWER",
+		.pin = {
+			.gpio = 0, 
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "radio-power",
+		},
+	},
+#endif
+	{
+		.name = "DEVICE_RESET",
+		.pin = {
+			.gpio = OMAP_GPIO(1,29),
+			.flags = GPIOF_IN,
+			.label = "reset",
+		},
+		.active_low = 1,
+	},
+	{
+		.name = "WIFI_BT_INT",
+		.pin = {
+			.gpio = OMAP_GPIO(4,12), /* 4_12 */
+			.flags = GPIOF_IN,
+			.label = "wifi-bt-int",
+		},
+		.capability = CAPA_BLUETOOTH,
+	},
+	{
+		.name = "WIFI_RESET",
+		.pin = {
+			.gpio = OMAP_GPIO(4,11), /* 4_11 */
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "wlan-enabled",
+		},
+		.capability = CAPA_WIFI,
+		.active_low = 0,
+	},
+	{
+		.name = "BT_RESET",
+		.pin = {
+			.gpio = OMAP_GPIO(4,10), /* 4_10 */
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "bt-enabled",
+		},
+		.capability = CAPA_BLUETOOTH,
+		.active_low = 0,
+	},
+	{
+		.name = "USBHUB_RESET",
+		.pin = {
+			.gpio = OMAP_GPIO(3, 15),
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "usbhub-reset",
+		},
+		.active_low = 0,
+	},
+	{
+		.name = "ETH_RESET",
+		.pin = {
+				.gpio = OMAP_GPIO(4,7), /* 4_7 */ 
+				.flags = GPIOF_OUT_INIT_HIGH,
+				.label = "eth-reset",
+		},
+		.active_low = 0,
+	},
+	{
+		.name = "GNSS_INT",
+		.pin = {
+			.gpio = OMAP_GPIO(5,12), /* 5_12 */
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "gnss-int",
+		},
+		.capability = CAPA_GPS,
+	},
+	{
+		.name = "GNSS_RESET",
+		.pin = {
+			.gpio = OMAP_GPIO(5,10), /* 5_10 */
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "gnss-reset",
+		},
+		.capability = CAPA_GPS,
+		.active_low = 0,
+	},
+#if 0
+    /* Link status comes directly from the MTQ out to the baseboard */
+	{
+		.name = "LS_LED", 
+		.pin = {
+			.gpio = 0,
+			.flags = GPIOF_IN,
+			.label = "led-ls",
+		},
+		.active_low = 1,
+	},
+#endif
+	{
+		.name = "STATUS_LED",
+		.pin = {
+			.gpio = OMAP_GPIO(0, 20),
+			.flags = GPIOF_OUT_INIT_LOW,
+			.label = "led-status",
+		},
+	},
+	{
+		.name = "CD", 
+		.pin = {
+			.gpio = OMAP_GPIO(0, 21),
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "led-cd",
+		},
+	},
+	{
+		.name = "LED1", 
+		.pin = {
+			.gpio = OMAP_GPIO(4, 26),
+			.flags = GPIOF_OUT_INIT_LOW,
+			.label = "led-sig1",
+		},
+	},
+	{
+		.name = "LED2", 
+		.pin = {
+			.gpio = OMAP_GPIO(4, 27),
+			.flags = GPIOF_OUT_INIT_LOW,
+			.label = "led-sig2",
+		},
+	},
+	{
+		.name = "LED3", 
+		.pin = {
+			.gpio = OMAP_GPIO(4, 28),
+			.flags = GPIOF_OUT_INIT_LOW,
+			.label = "led-sig3",
+		},
+	},
+	{ },
+};
+
+static DEVICE_ATTR_MTS(dev_attr_wifi_reset_mtcpm, "wlan-enabled",
+	mts_attr_show_gpio_pin, mts_attr_store_gpio_pin);
+static DEVICE_ATTR_MTS(dev_attr_bt_reset_mtcpm, "bt-enabled",
+	mts_attr_show_gpio_pin, mts_attr_store_gpio_pin);
+static DEVICE_ATTR_RO_MTS(dev_attr_wifi_bt_int_mtcpm, "wifi-bt-int",
+	mts_attr_show_gpio_pin);
+static DEVICE_ATTR_MTS(dev_attr_gnss_reset_mtcpm, "gnss-reset",
+	mts_attr_show_gpio_pin, mts_attr_store_gpio_pin);
+static DEVICE_ATTR_MTS(dev_attr_usbhub_reset_mtcpm, "usbhub-reset",
+	mts_attr_show_gpio_pin, mts_attr_store_gpio_pin);
+static DEVICE_ATTR_MTS(dev_attr_eth_reset_mtcpm, "eth-reset",
+	mts_attr_show_gpio_pin, mts_attr_store_gpio_pin);
+static DEVICE_ATTR_MTS(dev_attr_gnss_int_mtcpm, "gnss-int",
+	mts_attr_show_gpio_pin, mts_attr_store_gpio_pin);
+static DEVICE_ATTR_MTS(dev_attr_lora_reset_mtcpm, "reset",
+		mts_attr_show_lora_gpio_pin, mts_attr_store_lora_gpio_pin);
+static DEVICE_ATTR_RO_MTS(dev_attr_lora_cdone_mtcpm, "cdone",
+		mts_attr_show_lora_gpio_pin);
+static DEVICE_ATTR_MTS(dev_attr_lora_creset_mtcpm, "creset",
+		mts_attr_show_lora_gpio_pin, mts_attr_store_lora_gpio_pin);
+static DEVICE_ATTR_RO_MTS(dev_attr_lora_eui_mtcpm, "eui",
+		mts_attr_show_lora_product_info);
+static DEVICE_ATTR_RO_MTS(dev_attr_lora_product_id_mtcpm, "product-id",
+		mts_attr_show_lora_product_info);
+static DEVICE_ATTR_RO_MTS(dev_attr_lora_hw_version_mtcpm, "hw-version",
+		mts_attr_show_lora_product_info);
+static DEVICE_ATTR_RO_MTS(dev_attr_wifi_mac_mtcpm, "mac-wifi",
+	mts_attr_show_product_info);
+static DEVICE_ATTR_RO_MTS(dev_attr_bluetooth_mac_mtcpm, "mac-bluetooth",
+	mts_attr_show_product_info);
+
+static struct attribute *mtcpm_platform_attributes[] = {
+	&dev_attr_imei.attr,
+	&dev_attr_eth_mac.attr,
+	&dev_attr_reset.attr,
+	&dev_attr_reset_monitor.attr,
+	&dev_attr_reset_monitor_intervals.attr,
+
+	&dev_attr_led_status.attr,
+	&dev_attr_led_cd_gpio.attr,
+	&dev_attr_led_sig1_gpio.attr,
+	&dev_attr_led_sig2_gpio.attr,
+	&dev_attr_led_sig3_gpio.attr,
+
+	&dev_attr_usbhub_reset.attr,
+	&dev_attr_eth_reset.attr,
+        
+  // radio feature is last to be able to 
+  // easily remove radio.
+  // is_radio_power_attr_mtcdt() searches
+  // for this for truncation.
+    &dev_attr_radio_power.attr,  /* Must be first radio attribute */
+	&dev_attr_radio_reset.attr,
+
+	&dev_attr_radio_reset_backoffs.attr,
+	&dev_attr_radio_reset_backoff_index.attr,
+	&dev_attr_radio_reset_backoff_seconds.attr,
+		
+    &dev_attr_wifi_reset_mtcpm.attr,
+	&dev_attr_bt_reset_mtcpm.attr,
+	&dev_attr_wifi_bt_int_mtcpm.attr,
+		
+    &dev_attr_gnss_reset_mtcpm.attr,
+	&dev_attr_gnss_int_mtcpm.attr,
+	&dev_attr_wifi_mac_mtcpm.attr,
+        &dev_attr_bluetooth_mac_mtcpm.attr,
+	NULL,
+};
+
+
+
+static struct attribute_group mtcpm_platform_attribute_group = {
+	.attrs = mtcpm_platform_attributes
+};
+
+static int 
+is_radio_power_attr_mtcpm(struct attribute *attr)
+{
+    return (attr ==  &dev_attr_radio_power.attr);
+}
+
+static struct attribute *mtcpm_lora_attributes[] = {
+		&dev_attr_lora_eui_mtcpm.attr,
+		&dev_attr_lora_product_id_mtcpm.attr,
+		&dev_attr_lora_hw_version_mtcpm.attr,
+		&dev_attr_lora_reset_mtcpm.attr,
+		&dev_attr_lora_cdone_mtcpm.attr,
+		&dev_attr_lora_creset_mtcpm.attr,
+		NULL,
+};
+
+static struct attribute_group mtcpm_lora_attribute_group = {
+	.attrs = mtcpm_lora_attributes
+};
+
+static struct attribute *mtcpm_cpu_attributes[] = {
+	&dev_attr_vendor_id.attr,
+	&dev_attr_product_id.attr,
+	&dev_attr_device_id.attr,
+	&dev_attr_uuid.attr,
+	&dev_attr_hw_version.attr,
+	&dev_attr_imei.attr,
+        NULL,
+};
+
+
+static struct attribute_group mtcpm_cpu_attribute_group = {
+	.attrs = mtcpm_cpu_attributes
+};
+
+static struct kobject *mts_cpu_kobject = NULL;
+
+static int mts_cpu_dir_create(uint8_t hw_version)
+{
+    if (hw_version != MTCPM_0_0)
+        return 0;
+    
+    mts_cpu_kobject = kobject_create_and_add("cpu", &mts_io_platform_device->dev.kobj);
+    if (!mts_cpu_kobject) {
+            log_error("kobject_create_and_add for cpu directory failed");
+            return -ENOMEM;
+    }
+
+    if (sysfs_create_group(mts_cpu_kobject, &mtcpm_cpu_attribute_group)) {
+            log_error("sysfs_create_group failed to create cpu group");
+            return -ENOMEM;
+    }
+
+    return 0;
+}
+
+static void mts_cpu_dir_delete(void)
+{
+	if (mts_cpu_kobject) {
+		kobject_put(mts_cpu_kobject);
+                mts_cpu_kobject = NULL;
+	}
+}
+
diff --git a/io-module/machine/mths.c b/io-module/machine/mths.c
new file mode 100644
index 0000000..c19598d
--- /dev/null
+++ b/io-module/machine/mths.c
@@ -0,0 +1,883 @@
+/*
+ * mths.c
+ *
+ *  Created on: Apr 26, 2018
+ *      Author: leonid
+ */
+#include "at91gpio.h"
+#include "buttons.h"
+
+static struct gpio_pin gpio_pins_mths_0_0[] = {
+    {
+        .name = "RADIO_POWER_MONITOR",
+        .pin = {
+            .gpio = AT91_PIN_PA23,
+            .flags = GPIOF_IN,
+            .label = "radio-power-monitor",
+        },
+        .active_low = 0,
+    },
+    {
+        .name = "RADIO_RESET",
+        .pin = {
+            .gpio = AT91_PIN_PA22,
+            .flags = GPIOF_OUT_INIT_HIGH | GPIOF_OPEN_DRAIN,
+            .label = "radio-reset",
+        },
+        .active_low = 0,
+    },
+    {
+        .name = "RADIO_POWER",
+        .pin = {
+            .gpio = AT91_PIN_PA21,
+            .flags = GPIOF_OUT_INIT_HIGH | GPIOF_OPEN_DRAIN,
+            .label = "radio-power",
+        },
+        .active_low = 0,
+    },
+    {
+        .name = "DEVICE_RESET",
+        .pin = {
+            .gpio = AT91_PIN_PC4,
+            .flags = GPIOF_IN,
+            .label = "reset",
+        },
+        .active_low = 1,
+    },
+    {
+        .name = "WPS_BUTTON",
+        .pin = {
+            .gpio = AT91_PIN_PA13,
+            .flags = GPIOF_IN,
+            .label = "wps_button",
+        },
+        .active_low = 1,
+    },
+    {
+        .name = "BT_BUTTON",
+        .pin = {
+            //TODO return back .gpio = AT91_PIN_PC4,
+            .gpio = AT91_PIN_PA12,
+            .flags = GPIOF_IN,
+            .label = "bt_button",
+        },
+        .active_low = 1,
+    },
+    {
+        .name = "LS_LED",
+        .pin = {
+            .gpio = AT91_PIN_PC16,
+#if LED_LS_CONTROLLABLE
+            .flags = GPIOF_OUT_INIT_HIGH,
+#else
+            .flags = GPIOF_IN,
+#endif
+            .label = "led-ls",
+        },
+        .active_low = 1,
+    },
+    {
+        .name = "LED3",
+        .pin = {
+            .gpio = AT91_PIN_PC15,
+            .flags = GPIOF_OUT_INIT_HIGH,
+            .label = "led-wifi",
+        },
+        .active_low = 1,
+    },
+    {
+        .name = "LED3",
+        .pin = {
+            .gpio = AT91_PIN_PC15,
+            .flags = GPIOF_OUT_INIT_HIGH,
+            .label = "led-b",
+        },
+        .active_low = 1,
+    },
+    {
+        .name = "LED4",
+        .pin = {
+            .gpio = AT91_PIN_PC20,
+            .flags = GPIOF_OUT_INIT_HIGH,
+            .label = "led-bt",
+        },
+        .active_low = 1,
+    },
+    {
+        .name = "LED4",
+        .pin = {
+            .gpio = AT91_PIN_PC20,
+            .flags = GPIOF_OUT_INIT_HIGH,
+            .label = "led-c",
+        },
+        .active_low = 1,
+    },
+    {
+	    .name = "LED5",
+	    .pin = {
+	       .gpio = AT91_PIN_PC21,
+	        .flags = GPIOF_OUT_INIT_HIGH,
+	        .label = "led-status",
+	    },
+	    .active_low = 1,
+    },
+    {
+	    .name = "LED5",
+	    .pin = {
+	        .gpio = AT91_PIN_PC21,
+	        .flags = GPIOF_OUT_INIT_HIGH,
+	        .label = "led-cd",
+	    },
+	    .active_low = 1,
+    },
+    {
+        .name = "LED6",
+        .pin = {
+            .gpio = AT91_PIN_PC19,
+            .flags = GPIOF_OUT_INIT_HIGH,
+            .label = "led-sig3",
+        },
+        .active_low = 1,
+    },
+    {
+        .name = "LED6",
+        .pin = {
+            .gpio = AT91_PIN_PC19,
+            .flags = GPIOF_OUT_INIT_HIGH,
+            .label = "led-d",
+        },
+        .active_low = 1,
+    },
+    {
+        .name = "LED7",
+        .pin = {
+            .gpio = AT91_PIN_PC18,
+            .flags = GPIOF_OUT_INIT_HIGH,
+            .label = "led-sig2",
+        },
+        .active_low = 1,
+    },
+    {
+        .name = "LED7",
+        .pin = {
+            .gpio = AT91_PIN_PC18,
+            .flags = GPIOF_OUT_INIT_HIGH,
+            .label = "led-e",
+        },
+        .active_low = 1,
+    },
+    {
+        .name = "LED8",
+        .pin = {
+            .gpio = AT91_PIN_PC17,
+            .flags = GPIOF_OUT_INIT_HIGH,
+            .label = "led-sig1",
+        },
+        .active_low = 1,
+    },
+    {
+        .name = "LED8",
+        .pin = {
+            .gpio = AT91_PIN_PC17,
+            .flags = GPIOF_OUT_INIT_HIGH,
+            .label = "led-f",
+        },
+        .active_low = 1,
+    },
+
+    // The difference between MTRv1_0_0 and MTRv1_0_1 starts here
+    {
+        .name = "WIFI_BT_ULPWKUP",
+        .pin = {
+            .gpio = AT91_PIN_PB9,
+            .flags = GPIOF_IN,
+            .label = "wifi-bt-ulpwkup",
+        }
+    },
+    {
+        .name = "WIFI_BT_LPWKUP",
+        .pin = {
+            .gpio = AT91_PIN_PB11,
+            .flags = GPIOF_IN,
+            .label = "wifi-bt-lpwkup",
+        }
+    },
+    {
+        .name = "WIFI_BT_INT",
+        .pin = {
+            .gpio = AT91_PIN_PB13,
+            .flags = GPIOF_IN,
+            .label = "wifi-bt-int",
+        }
+    },
+    {
+        .name = "WIFI_BT_RESET",
+        .pin = {
+            .gpio = AT91_PIN_PB10,
+            .flags = GPIOF_OUT_INIT_HIGH,
+            .label = "wifi-bt-reset",
+        }
+    },
+    {
+        .name = "WIFI_BT_LPMODE",
+        .pin = {
+            .gpio = AT91_PIN_PB12,
+            .flags = GPIOF_IN,
+            .label = "wifi-bt-lpmode",
+        }
+    },
+    {
+        .name = "GNSS_RESET",
+        .pin = {
+            .gpio = AT91_PIN_PC6,
+            .flags = GPIOF_OUT_INIT_LOW,
+            .label = "gnss-reset",
+        }
+    },
+    {
+        .name = "USBHUB_RESET",
+        .pin = {
+            .gpio = AT91_PIN_PB6,
+            .flags = GPIOF_OUT_INIT_HIGH,
+            .label = "usbhub-reset",
+        }
+    },
+    {
+        .name = "GNSS_INT",
+        .pin = {
+            .gpio = AT91_PIN_PC7,
+            .flags = GPIOF_OUT_INIT_HIGH,
+            .label = "gnss-int",
+        }
+    },
+
+
+    { },
+};
+
+/* MTHS-0.1 has no WIFI LED */
+static struct gpio_pin gpio_pins_mths_0_1[] = {
+    {
+        .name = "RADIO_POWER_MONITOR",
+        .pin = {
+            .gpio = AT91_PIN_PA23,
+            .flags = GPIOF_IN,
+            .label = "radio-power-monitor",
+        },
+        .active_low = 0,
+    },
+    {
+        .name = "RADIO_RESET",
+        .pin = {
+            .gpio = AT91_PIN_PA22,
+            .flags = GPIOF_OUT_INIT_HIGH | GPIOF_OPEN_DRAIN,
+            .label = "radio-reset",
+        },
+        .active_low = 0,
+    },
+    {
+        .name = "RADIO_POWER",
+        .pin = {
+            .gpio = AT91_PIN_PA21,
+            .flags = GPIOF_OUT_INIT_HIGH | GPIOF_OPEN_DRAIN,
+            .label = "radio-power",
+        },
+        .active_low = 0,
+    },
+    {
+        .name = "DEVICE_RESET",
+        .pin = {
+            .gpio = AT91_PIN_PC4,
+            .flags = GPIOF_IN,
+            .label = "reset",
+        },
+        .active_low = 1,
+    },
+    {
+        .name = "WPS_BUTTON",
+        .pin = {
+            .gpio = AT91_PIN_PA13,
+            .flags = GPIOF_IN,
+            .label = "wps_button",
+        },
+        .active_low = 1,
+    },
+    {
+        .name = "BT_BUTTON",
+        .pin = {
+            //TODO return back .gpio = AT91_PIN_PC4,
+            .gpio = AT91_PIN_PA12,
+            .flags = GPIOF_IN,
+            .label = "bt_button",
+        },
+        .active_low = 1,
+    },
+    {
+        .name = "LS_LED",
+        .pin = {
+            .gpio = AT91_PIN_PC16,
+#if LED_LS_CONTROLLABLE
+            .flags = GPIOF_OUT_INIT_HIGH,
+#else
+            .flags = GPIOF_IN,
+#endif
+            .label = "led-ls",
+        },
+        .active_low = 1,
+    },
+    {
+        .name = "LED4",
+        .pin = {
+            .gpio = AT91_PIN_PC20,
+            .flags = GPIOF_OUT_INIT_HIGH,
+            .label = "led-bt",
+        },
+        .active_low = 1,
+    },
+    {
+        .name = "LED4",
+        .pin = {
+            .gpio = AT91_PIN_PC20,
+            .flags = GPIOF_OUT_INIT_HIGH,
+            .label = "led-c",
+        },
+        .active_low = 1,
+    },
+    {
+	    .name = "LED5",
+	    .pin = {
+	       .gpio = AT91_PIN_PC21,
+	        .flags = GPIOF_OUT_INIT_HIGH,
+	        .label = "led-status",
+	    },
+	    .active_low = 1,
+    },
+    {
+	    .name = "LED5",
+	    .pin = {
+	        .gpio = AT91_PIN_PC21,
+	        .flags = GPIOF_OUT_INIT_HIGH,
+	        .label = "led-cd",
+	    },
+	    .active_low = 1,
+    },
+    {
+        .name = "LED6",
+        .pin = {
+            .gpio = AT91_PIN_PC19,
+            .flags = GPIOF_OUT_INIT_HIGH,
+            .label = "led-sig3",
+        },
+        .active_low = 1,
+    },
+    {
+        .name = "LED6",
+        .pin = {
+            .gpio = AT91_PIN_PC19,
+            .flags = GPIOF_OUT_INIT_HIGH,
+            .label = "led-d",
+        },
+        .active_low = 1,
+    },
+    {
+        .name = "LED7",
+        .pin = {
+            .gpio = AT91_PIN_PC18,
+            .flags = GPIOF_OUT_INIT_HIGH,
+            .label = "led-sig2",
+        },
+        .active_low = 1,
+    },
+    {
+        .name = "LED7",
+        .pin = {
+            .gpio = AT91_PIN_PC18,
+            .flags = GPIOF_OUT_INIT_HIGH,
+            .label = "led-e",
+        },
+        .active_low = 1,
+    },
+    {
+        .name = "LED8",
+        .pin = {
+            .gpio = AT91_PIN_PC17,
+            .flags = GPIOF_OUT_INIT_HIGH,
+            .label = "led-sig1",
+        },
+        .active_low = 1,
+    },
+    {
+        .name = "LED8",
+        .pin = {
+            .gpio = AT91_PIN_PC17,
+            .flags = GPIOF_OUT_INIT_HIGH,
+            .label = "led-f",
+        },
+        .active_low = 1,
+    },
+
+    // The difference between MTRv1_0_0 and MTRv1_0_1 starts here
+    {
+        .name = "WIFI_BT_ULPWKUP",
+        .pin = {
+            .gpio = AT91_PIN_PB9,
+            .flags = GPIOF_IN,
+            .label = "wifi-bt-ulpwkup",
+        }
+    },
+    {
+        .name = "WIFI_BT_LPWKUP",
+        .pin = {
+            .gpio = AT91_PIN_PB11,
+            .flags = GPIOF_IN,
+            .label = "wifi-bt-lpwkup",
+        }
+    },
+    {
+        .name = "WIFI_BT_INT",
+        .pin = {
+            .gpio = AT91_PIN_PB13,
+            .flags = GPIOF_IN,
+            .label = "wifi-bt-int",
+        }
+    },
+    {
+        .name = "WIFI_BT_RESET",
+        .pin = {
+            .gpio = AT91_PIN_PB10,
+            .flags = GPIOF_OUT_INIT_HIGH,
+            .label = "wifi-bt-reset",
+        }
+    },
+    {
+        .name = "WIFI_BT_LPMODE",
+        .pin = {
+            .gpio = AT91_PIN_PB12,
+            .flags = GPIOF_IN,
+            .label = "wifi-bt-lpmode",
+        }
+    },
+    {
+        .name = "GNSS_RESET",
+        .pin = {
+            .gpio = AT91_PIN_PC6,
+            .flags = GPIOF_OUT_INIT_LOW,
+            .label = "gnss-reset",
+        }
+    },
+    {
+        .name = "USBHUB_RESET",
+        .pin = {
+            .gpio = AT91_PIN_PB6,
+            .flags = GPIOF_OUT_INIT_HIGH,
+            .label = "usbhub-reset",
+        }
+    },
+    {
+        .name = "GNSS_INT",
+        .pin = {
+            .gpio = AT91_PIN_PC7,
+            .flags = GPIOF_OUT_INIT_HIGH,
+            .label = "gnss-int",
+        }
+    },
+
+
+    { },
+};
+
+button_info_t mths_wps_button = {
+        .name = "User Push Button WPS",
+        .label_pin = "wps_button",
+        .label_monitor = "wps_button-monitor",
+        .label_monitor_intervals = "wps_button-monitor-intervals",
+
+        /* Signals */
+        .short_signal = SIGUSR1,
+        .long_signal  = SIGUSR2,
+        .short_signal = SIGHUP,
+
+        /* Intervals */
+        .short_interval = BUTTON_HOLD_COUNT,
+        .long_interval = BUTTON_LONG_HOLD_COUNT,
+};
+
+button_info_t mths_bt_button = {
+        .name = "User Push Button BT",
+        .label_pin = "bt_button",
+        .label_monitor = "bt_button-monitor",
+        .label_monitor_intervals = "bt_button-monitor-intervals",
+
+        /* Signals */
+        .short_signal = SIGUSR1,
+        .long_signal  = SIGUSR2,
+        .short_signal = SIGHUP,
+
+        /* Intervals */
+        .short_interval = BUTTON_HOLD_COUNT,
+        .long_interval = BUTTON_LONG_HOLD_COUNT,
+};
+
+/* MTHS 0.0 and 0.1 have same buttons. */
+static button_info_pt mths_buttons_0_0[] = {
+        &reset_button,
+        &mths_wps_button,
+        &mths_bt_button,
+        NULL,
+};
+
+static DEVICE_ATTR_MTS(dev_attr_wps_button_monitor_intervals_mths,
+        mths_wps_button.label_monitor_intervals,
+        mts_attr_show_button_monitor_intervals,
+        mts_attr_store_button_monitor_intervals);
+
+static DEVICE_ATTR_MTS(dev_attr_wps_button_monitor_mths,
+        mths_wps_button.label_monitor,
+        mts_attr_show_button_monitor,
+        mts_attr_store_button_monitor);
+
+static DEVICE_ATTR_RO_MTS(dev_attr_wps_button_pin_mths,
+        mths_wps_button.label_pin,
+        mts_attr_show_gpio_pin);
+
+
+static DEVICE_ATTR_MTS(dev_attr_bt_button_monitor_intervals_mths,
+        mths_bt_button.label_monitor_intervals,
+        mts_attr_show_button_monitor_intervals,
+        mts_attr_store_button_monitor_intervals);
+
+static DEVICE_ATTR_MTS(dev_attr_bt_button_monitor_mths,
+        mths_bt_button.label_monitor,
+        mts_attr_show_button_monitor,
+        mts_attr_store_button_monitor);
+
+static DEVICE_ATTR_RO_MTS(dev_attr_bt_button_pin_mths,
+        mths_bt_button.label_pin,
+        mts_attr_show_gpio_pin);
+
+
+/* radio control (power/reset) for mtr */
+static int radio_off_mths(void)
+{
+    int value;
+    struct gpio_pin *pwrmon_pin = gpio_pin_by_attr_name("radio-power-monitor");
+    struct gpio_pin *onoff_pin = gpio_pin_by_attr_name("radio-power");
+    struct gpio_pin *rst_pin = gpio_pin_by_attr_name("radio-reset");
+
+    if (!onoff_pin || !pwrmon_pin || !rst_pin) {
+        return -ENODEV;
+    }
+
+    value = gpio_get_value(pwrmon_pin->pin.gpio);
+    if(value == 0) {
+        log_error("radio is already off");
+        return -EINVAL;
+    }
+
+    // drive on/off pin low for at least 3 sec
+    log_info("shutting down radio");
+    gpio_set_value(onoff_pin->pin.gpio, 0);
+
+    msleep(3500);
+
+    // set on/off pin high
+    gpio_set_value(onoff_pin->pin.gpio, 1);
+
+    msleep(200);
+
+    // check that power is low
+    value = gpio_get_value(pwrmon_pin->pin.gpio);
+    if(value != 0) {
+        log_warning("radio is still on. performing radio reset.");
+        //Perform Hard Reset
+        gpio_set_value(rst_pin->pin.gpio, 0);
+
+        msleep(500);
+
+        // set pin high
+        gpio_set_value(rst_pin->pin.gpio, 1);
+    } else {
+        log_info("radio has been shut down");
+    }
+
+    return 0;
+}
+
+static int radio_on_mths(void)
+{
+    int value;
+    struct gpio_pin *pwrmon_pin = gpio_pin_by_attr_name("radio-power-monitor");
+    struct gpio_pin *onoff_pin = gpio_pin_by_attr_name("radio-power");
+    struct gpio_pin *rst_pin = gpio_pin_by_attr_name("radio-reset");
+
+    if (!onoff_pin || !pwrmon_pin || !rst_pin) {
+        return -ENODEV;
+    }
+
+    value = gpio_get_value(pwrmon_pin->pin.gpio);
+    if(value != 0) {
+        log_error("radio is already on");
+        return -EINVAL;
+    }
+
+    // drive on/off pin low for at least 5 sec
+    log_info("turning on radio");
+    gpio_set_value(onoff_pin->pin.gpio, 0);
+
+    // ref:Telit_LE910_V2_Hardware_User_Guide_r9.pdf
+    //    pg 32: When USB is connected or after firmware updating,
+    //    delay must be equal at least to 10 seconds.
+    msleep(10500);
+
+    // set on/off pin high
+    gpio_set_value(onoff_pin->pin.gpio, 1);
+    log_info("radio_on_mths: radio should be coming up");
+
+    msleep(200);
+
+    // check that power is high
+    value = gpio_get_value(pwrmon_pin->pin.gpio);
+    if(value == 0) {
+        log_warning("radio_on_mths: radio is still off. performing radio reset");
+        //Perform Hard Reset
+        gpio_set_value(rst_pin->pin.gpio, 0);
+
+        msleep(500);
+
+        // set pin high
+        gpio_set_value(rst_pin->pin.gpio, 1);
+    } else {
+        log_info("radio has been turned on");
+    }
+
+    return 0;
+}
+
+static int radio_reset_mths(void)
+{
+    struct gpio_pin *onoff_pin = gpio_pin_by_attr_name("radio-power");
+    struct gpio_pin *rst_pin = gpio_pin_by_attr_name("radio-reset");
+
+    if (!rst_pin || !onoff_pin) {
+        return -ENODEV;
+    }
+
+    // drive reset pin low for 500ms
+    gpio_set_value(rst_pin->pin.gpio, 0);
+
+    msleep(500);
+
+    // set pin high
+    gpio_set_value(rst_pin->pin.gpio, 1);
+
+    // wait for 2 sec before toggling on/off pin
+    msleep(2000);
+
+    // drive on/off pin low for 10.5 sec
+    gpio_set_value(onoff_pin->pin.gpio, 0);
+
+    log_info("Wait 10.5 seconds for on/off pin");
+    msleep(10500);
+
+    log_info("Done with wait 10.5 seconds for on/off pin");
+    // set on/off pin high
+    gpio_set_value(onoff_pin->pin.gpio, 1);
+    msleep(200); // Delay for status pin to switch
+    return 0;
+}
+
+static ssize_t mts_attr_store_radio_power_mths(struct device *dev,
+        struct device_attribute *attr, const char *buf, size_t count)
+{
+    int value;
+    int err;
+
+    if (sscanf(buf, "%i", &value) != 1) {
+        return -EINVAL;
+    }
+    if (value == 0) {
+        mutex_lock(&mts_io_mutex);
+        err = radio_off_mths();
+        mutex_unlock(&mts_io_mutex);
+    } else {
+        mutex_lock(&mts_io_mutex);
+        err = radio_on_mths();
+        mutex_unlock(&mts_io_mutex);
+    }
+
+    if (err) {
+        return err;
+    }
+
+    return count;
+}
+
+static ssize_t mts_attr_store_radio_reset_mths(struct device *dev,
+        struct device_attribute *attr, const char *buf, size_t count)
+{
+    int value; /* 0 = normal reset; -1 = forced reset */
+    int err;
+
+    if (sscanf(buf, "%i", &value) != 1) {
+        return -EINVAL;
+    }
+    if (value != 0 && value != -1) {
+        return -EINVAL;
+    }
+
+    /* check reset timings is enabled */
+    if (value != -1 && NULL != timings_data) {
+        /* check reset timer is started */
+        if (radio_reset_timer_is_start == 1) {
+            log_info("radio reset timer is running. \n");
+            return count;
+        }
+
+        /* check reset timer available is started */
+        if (radio_reset_available_timer_is_start == 1) {
+            del_timer(&radio_reset_available_timer);
+            radio_reset_available_timer_is_start = 0;
+        }
+
+        /* reset timer not started, start it */
+        mod_timer(&radio_reset_timer, jiffies + msecs_to_jiffies((timings_data[timings_data_index]) * 1000));
+        //log_info("radio reset timer is start = [%d]\n", time_now_secs());
+        /* save timings_data_stop_seconds */
+        timings_data_stop_seconds = timings_data[timings_data_index] + time_now_secs();
+        radio_reset_timer_is_start = 1;
+    }
+
+    log_info("radio is reset\n");
+
+    mutex_lock(&mts_io_mutex);
+
+    err = radio_reset_mths();
+
+    mutex_unlock(&mts_io_mutex);
+
+    if (err) {
+        return err;
+    }
+
+    return count;
+}
+
+static ssize_t mts_attr_show_radio_power_mths(struct device *dev,
+            struct device_attribute *attr, char *buf)
+{
+    int value;
+    struct gpio_pin *pwrmon_pin = gpio_pin_by_attr_name("radio-power-monitor");
+
+    if ( !pwrmon_pin ) {
+        return -ENODEV;
+    }
+
+    value = gpio_get_value(pwrmon_pin->pin.gpio);
+    return sprintf(buf, "%d\n", value);
+}
+
+static DEVICE_ATTR_MTS(dev_attr_radio_power_mths, "radio-power",
+    mts_attr_show_radio_power_mths, mts_attr_store_radio_power_mths);
+
+static DEVICE_ATTR_MTS(dev_attr_radio_reset_mths, "radio-reset",
+    mts_attr_show_gpio_pin, mts_attr_store_radio_reset_mths);
+
+
+static DEVICE_ATTR_MTS(dev_attr_led_wifi_gpio_mths, "led-wifi",
+    mts_attr_show_gpio_pin, mts_attr_store_gpio_pin);
+
+static DEVICE_ATTR_MTS(dev_attr_led_bt_gpio_mths, "led-bt",
+    mts_attr_show_gpio_pin, mts_attr_store_gpio_pin);
+
+static DEVICE_ATTR_MTS(dev_attr_led_f_gpio_mths, "led-f",
+    mts_attr_show_gpio_pin, mts_attr_store_gpio_pin);
+
+static DEVICE_ATTR_RO_MTS(dev_attr_wifi_mac_mths, "mac-wifi",
+    mts_attr_show_product_info);
+
+static DEVICE_ATTR_RO_MTS(dev_attr_bluetooth_mac_mths, "mac-bluetooth",
+    mts_attr_show_product_info);
+
+static DEVICE_ATTR_MTS(dev_attr_wifi_bt_lpwkup_mths, "wifi-bt-lpwkup",
+    mts_attr_show_gpio_pin, mts_attr_store_gpio_pin);
+
+static DEVICE_ATTR_MTS(dev_attr_wifi_bt_ulpwkup_mths, "wifi-bt-ulpwkup",
+    mts_attr_show_gpio_pin, mts_attr_store_gpio_pin);
+
+static DEVICE_ATTR_MTS(dev_attr_wifi_bt_reset_mths, "wifi-bt-reset",
+    mts_attr_show_gpio_pin, mts_attr_store_gpio_pin);
+
+static DEVICE_ATTR_RO_MTS(dev_attr_wifi_bt_lpmode_mths, "wifi-bt-lpmode",
+    mts_attr_show_gpio_pin);
+
+static DEVICE_ATTR_RO_MTS(dev_attr_wifi_bt_int_mths, "wifi-bt-int",
+    mts_attr_show_gpio_pin);
+
+static DEVICE_ATTR_MTS(dev_attr_gnss_reset_mths, "gnss-reset",
+    mts_attr_show_gpio_pin, mts_attr_store_gpio_pin);
+
+static DEVICE_ATTR_MTS(dev_attr_usbhub_reset_mths, "usbhub-reset",
+    mts_attr_show_gpio_pin, mts_attr_store_gpio_pin);
+
+static DEVICE_ATTR_RO_MTS(dev_attr_gnss_int_mths, "gnss-int",
+    mts_attr_show_gpio_pin);
+
+
+
+static struct attribute *mths_0_0_platform_attributes[] = {
+    &dev_attr_vendor_id.attr,
+    &dev_attr_product_id.attr,
+    &dev_attr_device_id.attr,
+    &dev_attr_uuid.attr,
+    &dev_attr_hw_version.attr,
+    &dev_attr_imei.attr,
+    &dev_attr_wifi_mac_mths.attr,
+    &dev_attr_bluetooth_mac_mths.attr,
+    &dev_attr_has_radio.attr,
+
+    &dev_attr_reset.attr,
+    &dev_attr_reset_monitor.attr,
+    &dev_attr_reset_monitor_intervals.attr,
+    &dev_attr_wps_button_pin_mths.attr,
+    &dev_attr_wps_button_monitor_mths.attr,
+    &dev_attr_wps_button_monitor_intervals_mths.attr,
+    &dev_attr_bt_button_pin_mths.attr,
+    &dev_attr_bt_button_monitor_mths.attr,
+    &dev_attr_bt_button_monitor_intervals_mths.attr,
+
+    &dev_attr_radio_power_mths.attr,
+    &dev_attr_radio_reset_mths.attr,
+
+    &dev_attr_radio_reset_backoffs.attr,
+    &dev_attr_radio_reset_backoff_index.attr,
+    &dev_attr_radio_reset_backoff_seconds.attr,
+
+    &dev_attr_wifi_bt_lpwkup_mths.attr,
+    &dev_attr_wifi_bt_ulpwkup_mths.attr,
+    &dev_attr_wifi_bt_reset_mths.attr,
+    &dev_attr_wifi_bt_lpmode_mths.attr,
+    &dev_attr_wifi_bt_int_mths.attr,
+    &dev_attr_gnss_reset_mths.attr,
+    &dev_attr_usbhub_reset_mths.attr,
+    &dev_attr_gnss_int_mths.attr,
+
+    &dev_attr_led_status.attr,
+    &dev_attr_led_cd_gpio.attr,
+    &dev_attr_led_sig1_gpio.attr,
+    &dev_attr_led_sig2_gpio.attr,
+    &dev_attr_led_sig3_gpio.attr,
+    &dev_attr_led_wifi_gpio_mths.attr,
+    &dev_attr_led_bt_gpio_mths.attr,
+
+    &dev_attr_led_b_gpio.attr,
+    &dev_attr_led_c_gpio.attr,
+    &dev_attr_led_d_gpio.attr,
+    &dev_attr_led_e_gpio.attr,
+    &dev_attr_led_f_gpio_mths.attr,
+
+    NULL,
+};
+
+static struct attribute_group mths_0_0_platform_attribute_group = {
+    .attrs = mths_0_0_platform_attributes
+};
diff --git a/io-module/machine/mtr.c b/io-module/machine/mtr.c
new file mode 100644
index 0000000..8664984
--- /dev/null
+++ b/io-module/machine/mtr.c
@@ -0,0 +1,2001 @@
+#include "at91gpio.h"
+static struct gpio_pin gpio_pins_mtr_0_0[] = {
+	{
+		.name = "ETH_RESET",
+		.pin = {
+			.gpio = AT91_PIN_PC6,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "eth-reset",
+		},
+		.active_low = 0,
+	},
+	{
+		.name = "RADIO_POWER_MONITOR",
+		.pin = {
+			.gpio = AT91_PIN_PA23,
+			.flags = GPIOF_IN,
+			.label = "radio-power-monitor",
+		},
+		.active_low = 0,
+	},
+	{
+		.name = "RADIO_RESET",
+		.pin = {
+			.gpio = AT91_PIN_PA22,
+			.flags = GPIOF_OUT_INIT_HIGH | GPIOF_OPEN_DRAIN,
+			.label = "radio-reset",
+		},
+		.active_low = 0,
+	},
+	{
+		.name = "RADIO_POWER",
+		.pin = {
+			.gpio = AT91_PIN_PA21,
+			.flags = GPIOF_OUT_INIT_HIGH | GPIOF_OPEN_DRAIN,
+			.label = "radio-power",
+		},
+		.active_low = 0,
+	},
+	{
+		.name = "DEVICE_RESET",
+		.pin = {
+			.gpio = AT91_PIN_PC4,
+			.flags = GPIOF_IN,
+			.label = "reset",
+		},
+		.active_low = 1,
+	},
+	{
+		.name = "LS_LED",
+		.pin = {
+			.gpio = AT91_PIN_PC16,
+#if LED_LS_CONTROLLABLE
+			.flags = GPIOF_OUT_INIT_HIGH,
+#else
+			.flags = GPIOF_IN,
+#endif
+			.label = "led-ls",
+		},
+		.active_low = 1,
+	},
+	{
+		.name = "STATUS_LED",
+		.pin = {
+			.gpio = AT91_PIN_PC21,
+			.flags = GPIOF_OUT_INIT_LOW,
+			.label = "led-status",
+		},
+		.active_low = 1,
+	},
+	{
+		.name = "LED3",
+		.pin = {
+			.gpio = AT91_PIN_PC15,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "led-wifi",
+		},
+		.active_low = 1,
+	},
+	{
+		.name = "LED3",
+		.pin = {
+			.gpio = AT91_PIN_PC15,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "led-b",
+		},
+		.active_low = 1,
+	},
+	{
+		.name = "LED4",
+		.pin = {
+			.gpio = AT91_PIN_PC20,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "led-cd",
+		},
+		.active_low = 1,
+	},
+	{
+		.name = "LED4",
+		.pin = {
+			.gpio = AT91_PIN_PC20,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "led-c",
+		},
+		.active_low = 1,
+	},
+	{
+		.name = "LED6",
+		.pin = {
+			.gpio = AT91_PIN_PC19,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "led-sig1",
+		},
+		.active_low = 1,
+	},
+	{
+		.name = "LED6",
+		.pin = {
+			.gpio = AT91_PIN_PC19,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "led-d",
+		},
+		.active_low = 1,
+	},
+	{
+		.name = "LED7",
+		.pin = {
+			.gpio = AT91_PIN_PC18,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "led-sig2",
+		},
+		.active_low = 1,
+	},
+	{
+		.name = "LED7",
+		.pin = {
+			.gpio = AT91_PIN_PC18,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "led-e",
+		},
+		.active_low = 1,
+	},
+	{
+		.name = "LED8",
+		.pin = {
+			.gpio = AT91_PIN_PC17,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "led-sig3",
+		},
+		.active_low = 1,
+	},
+	{
+		.name = "LED8",
+		.pin = {
+			.gpio = AT91_PIN_PC17,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "led-f",
+		},
+		.active_low = 1,
+	},
+	{
+		.name = "RI_B",
+		.pin = {
+			.gpio = AT91_PIN_PC25,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "extserial-ri",
+		},
+		.active_low = 1,
+	},
+	{
+		.name = "DTR_B",
+		.pin = {
+			.gpio = AT91_PIN_PC26,
+			.flags = GPIOF_IN,
+			.label = "extserial-dtr",
+		},
+		.active_low = 1,
+	},
+	{
+		.name = "DSR_B",
+		.pin = {
+			.gpio = AT91_PIN_PC27,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "extserial-dsr",
+		},
+		.active_low = 1,
+	},
+	{
+		.name = "DCD_B",
+		.pin = {
+			.gpio = AT91_PIN_PC28,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "extserial-dcd",
+		},
+		.active_low = 1,
+	},
+	{
+		.name = "BT_EN",
+		.pin = {
+			.gpio = AT91_PIN_PA28,
+			.flags = GPIOF_OUT_INIT_LOW,
+			.label = "bt-enabled",
+		},
+		.active_low = 0,
+	},
+	{
+		.name = "WLAN_EN",
+		.pin = {
+			.gpio = AT91_PIN_PA27,
+			.flags = GPIOF_OUT_INIT_LOW,
+			.label = "wlan-enabled",
+		},
+		.active_low = 0,
+	},
+	{ },
+};
+
+static struct gpio_pin gpio_pins_mtr_0_1[] = {
+	{
+		.name = "ETH_RESET",
+		.pin = {
+			.gpio = AT91_PIN_PC6,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "eth-reset",
+		},
+		.active_low = 0,
+	},
+	{
+		.name = "RADIO_POWER_MONITOR",
+		.pin = {
+			.gpio = AT91_PIN_PA23,
+			.flags = GPIOF_IN,
+			.label = "radio-power-monitor",
+		},
+		.active_low = 0,
+	},
+	{
+		.name = "RADIO_RESET",
+		.pin = {
+			.gpio = AT91_PIN_PA22,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "radio-reset",
+		},
+		.active_low = 0,
+	},
+	{
+		.name = "RADIO_POWER",
+		.pin = {
+			.gpio = AT91_PIN_PA21,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "radio-power",
+		},
+		.active_low = 0,
+	},
+	{
+		.name = "DEVICE_RESET",
+		.pin = {
+			.gpio = AT91_PIN_PC4,
+			.flags = GPIOF_IN,
+			.label = "reset",
+		},
+		.active_low = 1,
+	},
+	{
+		.name = "LS_LED",
+		.pin = {
+			.gpio = AT91_PIN_PC16,
+#if LED_LS_CONTROLLABLE
+			.flags = GPIOF_OUT_INIT_HIGH,
+#else
+			.flags = GPIOF_IN,
+#endif
+			.label = "led-ls",
+		},
+		.active_low = 1,
+	},
+	{
+		.name = "STATUS_LED",
+		.pin = {
+			.gpio = AT91_PIN_PC21,
+			.flags = GPIOF_OUT_INIT_LOW,
+			.label = "led-status",
+		},
+		.active_low = 1,
+	},
+	{
+		.name = "LED3",
+		.pin = {
+			.gpio = AT91_PIN_PC15,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "led-wifi",
+		},
+		.active_low = 1,
+	},
+	{
+		.name = "LED3",
+		.pin = {
+			.gpio = AT91_PIN_PC15,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "led-b",
+		},
+		.active_low = 1,
+	},
+	{
+		.name = "LED4",
+		.pin = {
+			.gpio = AT91_PIN_PC20,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "led-cd",
+		},
+		.active_low = 1,
+	},
+	{
+		.name = "LED4",
+		.pin = {
+			.gpio = AT91_PIN_PC20,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "led-c",
+		},
+		.active_low = 1,
+	},
+	{
+		.name = "LED6",
+		.pin = {
+			.gpio = AT91_PIN_PC19,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "led-sig1",
+		},
+		.active_low = 1,
+	},
+	{
+		.name = "LED6",
+		.pin = {
+			.gpio = AT91_PIN_PC19,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "led-d",
+		},
+		.active_low = 1,
+	},
+	{
+		.name = "LED7",
+		.pin = {
+			.gpio = AT91_PIN_PC18,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "led-sig2",
+		},
+		.active_low = 1,
+	},
+	{
+		.name = "LED7",
+		.pin = {
+			.gpio = AT91_PIN_PC18,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "led-e",
+		},
+		.active_low = 1,
+	},
+	{
+		.name = "LED8",
+		.pin = {
+			.gpio = AT91_PIN_PC17,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "led-sig3",
+		},
+		.active_low = 1,
+	},
+	{
+		.name = "LED8",
+		.pin = {
+			.gpio = AT91_PIN_PC17,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "led-f",
+		},
+		.active_low = 1,
+	},
+	{
+		.name = "RI_B",
+		.pin = {
+			.gpio = AT91_PIN_PC25,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "extserial-ri",
+		},
+		.active_low = 1,
+	},
+	{
+		.name = "DTR_B",
+		.pin = {
+			.gpio = AT91_PIN_PC26,
+			.flags = GPIOF_IN,
+			.label = "extserial-dtr",
+		},
+		.active_low = 1,
+	},
+	{
+		.name = "DSR_B",
+		.pin = {
+			.gpio = AT91_PIN_PC27,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "extserial-dsr",
+		},
+		.active_low = 1,
+	},
+	{
+		.name = "DCD_B",
+		.pin = {
+			.gpio = AT91_PIN_PC28,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "extserial-dcd",
+		},
+		.active_low = 1,
+	},
+	{
+		.name = "BT_EN",
+		.pin = {
+			.gpio = AT91_PIN_PA28,
+			.flags = GPIOF_OUT_INIT_LOW,
+			.label = "bt-enabled",
+		},
+		.active_low = 0,
+	},
+	{
+		.name = "WLAN_EN",
+		.pin = {
+			.gpio = AT91_PIN_PA27,
+			.flags = GPIOF_OUT_INIT_LOW,
+			.label = "wlan-enabled",
+		},
+		.active_low = 0,
+	},
+	{ },
+};
+
+static struct gpio_pin gpio_pins_mtrv1_0_0[] = {
+	{
+		.name = "ETH_RESET",
+		.pin = {
+			.gpio = AT91_PIN_PC6,
+			.flags = GPIOF_OUT_INIT_HIGH | GPIOF_OPEN_DRAIN,  /* without GPIOF_OPEN_DRAIN causes issues with the Micrel KSZ8091RNBCA (RMII) PHY */
+			.label = "eth-reset",
+		},
+		.active_low = 0,
+	},
+	{
+		.name = "RADIO_POWER_MONITOR",
+		.pin = {
+			.gpio = AT91_PIN_PA23,
+			.flags = GPIOF_IN,
+			.label = "radio-power-monitor",
+		},
+		.active_low = 0,
+	},
+	{
+		.name = "RADIO_RESET",
+		.pin = {
+			.gpio = AT91_PIN_PA22,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "radio-reset",
+		},
+		.active_low = 0,
+	},
+	{
+		.name = "RADIO_POWER",
+		.pin = {
+			.gpio = AT91_PIN_PA21,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "radio-power",
+		},
+		.active_low = 0,
+	},
+	{
+		.name = "DEVICE_RESET",
+		.pin = {
+			.gpio = AT91_PIN_PC4,
+			.flags = GPIOF_IN,
+			.label = "reset",
+		},
+		.active_low = 1,
+	},
+	{
+		.name = "LS_LED",
+		.pin = {
+			.gpio = AT91_PIN_PC4,
+#if LED_LS_CONTROLLABLE
+			.flags = GPIOF_OUT_INIT_HIGH,
+#else
+			.flags = GPIOF_IN,
+#endif
+			.label = "led-ls",
+		},
+		.active_low = 1,
+	},
+	{
+		.name = "STATUS_LED",
+		.pin = {
+			.gpio = AT91_PIN_PC21,
+			.flags = GPIOF_OUT_INIT_LOW,
+			.label = "led-status",
+		},
+		.active_low = 1,
+	},
+	{
+		.name = "LED3",
+		.pin = {
+			.gpio = AT91_PIN_PC15,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "led-wifi",
+		},
+		.active_low = 1,
+	},
+	{
+		.name = "LED3",
+		.pin = {
+			.gpio = AT91_PIN_PC15,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "led-b",
+		},
+		.active_low = 1,
+	},
+	{
+		.name = "LED4",
+		.pin = {
+			.gpio = AT91_PIN_PC20,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "led-cd",
+		},
+		.active_low = 1,
+	},
+	{
+		.name = "LED4",
+		.pin = {
+			.gpio = AT91_PIN_PC20,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "led-c",
+		},
+		.active_low = 1,
+	},
+	{
+		.name = "LED6",
+		.pin = {
+			.gpio = AT91_PIN_PC19,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "led-sig1",
+		},
+		.active_low = 1,
+	},
+	{
+		.name = "LED6",
+		.pin = {
+			.gpio = AT91_PIN_PC19,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "led-d",
+		},
+		.active_low = 1,
+	},
+	{
+		.name = "LED7",
+		.pin = {
+			.gpio = AT91_PIN_PC18,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "led-sig2",
+		},
+		.active_low = 1,
+	},
+	{
+		.name = "LED7",
+		.pin = {
+			.gpio = AT91_PIN_PC18,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "led-e",
+		},
+		.active_low = 1,
+	},
+	{
+		.name = "LED8",
+		.pin = {
+			.gpio = AT91_PIN_PC17,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "led-sig3",
+		},
+		.active_low = 1,
+	},
+	{
+		.name = "LED8",
+		.pin = {
+			.gpio = AT91_PIN_PC17,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "led-f",
+		},
+		.active_low = 1,
+	},
+	{
+		.name = "RI_B",
+		.pin = {
+			.gpio = AT91_PIN_PC25,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "extserial-ri",
+		},
+		.active_low = 1,
+	},
+	{
+		.name = "DTR_B",
+		.pin = {
+			.gpio = AT91_PIN_PC26,
+			.flags = GPIOF_IN,
+			.label = "extserial-dtr",
+		},
+		.active_low = 1,
+	},
+	{
+		.name = "DSR_B",
+		.pin = {
+			.gpio = AT91_PIN_PC27,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "extserial-dsr",
+		},
+		.active_low = 1,
+	},
+	{
+		.name = "DCD_B",
+		.pin = {
+			.gpio = AT91_PIN_PC28,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "extserial-dcd",
+		},
+		.active_low = 1,
+	},
+	{
+		.name = "BT_EN",
+		.pin = {
+			.gpio = AT91_PIN_PA28,
+			.flags = GPIOF_OUT_INIT_LOW,
+			.label = "bt-enabled",
+		},
+		.active_low = 0,
+	},
+	{
+		.name = "WLAN_EN",
+		.pin = {
+			.gpio = AT91_PIN_PA27,
+			.flags = GPIOF_OUT_INIT_LOW,
+			.label = "wlan-enabled",
+		},
+		.active_low = 0,
+	},
+	{ },
+};
+
+
+static struct gpio_pin gpio_pins_mtrv1_0_1[] = {
+	{
+		.name = "ETH_RESET",
+		.pin = {
+			.gpio = AT91_PIN_PC6,
+			.flags = GPIOF_OUT_INIT_HIGH | GPIOF_OPEN_DRAIN,  /* without GPIOF_OPEN_DRAIN causes issues with the Micrel KSZ8091RNBCA (RMII) PHY */
+			.label = "eth-reset",
+		},
+		.active_low = 0,
+	},
+	{
+		.name = "RADIO_POWER_MONITOR",
+		.pin = {
+			.gpio = AT91_PIN_PA23,
+			.flags = GPIOF_IN,
+			.label = "radio-power-monitor",
+		},
+		.active_low = 0,
+	},
+	{
+		.name = "RADIO_RESET",
+		.pin = {
+			.gpio = AT91_PIN_PA22,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "radio-reset",
+		},
+		.active_low = 0,
+	},
+	{
+		.name = "RADIO_POWER",
+		.pin = {
+			.gpio = AT91_PIN_PA21,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "radio-power",
+		},
+		.active_low = 0,
+	},
+	{
+		.name = "DEVICE_RESET",
+		.pin = {
+			.gpio = AT91_PIN_PC4,
+			.flags = GPIOF_IN,
+			.label = "reset",
+		},
+		.active_low = 1,
+	},
+	{
+		.name = "LS_LED",
+		.pin = {
+			.gpio = AT91_PIN_PC4,
+#if LED_LS_CONTROLLABLE
+			.flags = GPIOF_OUT_INIT_HIGH,
+#else
+			.flags = GPIOF_IN,
+#endif
+			.label = "led-ls",
+		},
+		.active_low = 1,
+	},
+	{
+		.name = "STATUS_LED",
+		.pin = {
+			.gpio = AT91_PIN_PC21,
+			.flags = GPIOF_OUT_INIT_LOW,
+			.label = "led-status",
+		},
+		.active_low = 1,
+	},
+	{
+		.name = "LED3",
+		.pin = {
+			.gpio = AT91_PIN_PC15,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "led-wifi",
+		},
+		.active_low = 1,
+	},
+	{
+		.name = "LED3",
+		.pin = {
+			.gpio = AT91_PIN_PC15,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "led-b",
+		},
+		.active_low = 1,
+	},
+	{
+		.name = "LED4",
+		.pin = {
+			.gpio = AT91_PIN_PC20,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "led-cd",
+		},
+		.active_low = 1,
+	},
+	{
+		.name = "LED4",
+		.pin = {
+			.gpio = AT91_PIN_PC20,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "led-c",
+		},
+		.active_low = 1,
+	},
+	{
+		.name = "LED6",
+		.pin = {
+			.gpio = AT91_PIN_PC19,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "led-sig1",
+		},
+		.active_low = 1,
+	},
+	{
+		.name = "LED6",
+		.pin = {
+			.gpio = AT91_PIN_PC19,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "led-d",
+		},
+		.active_low = 1,
+	},
+	{
+		.name = "LED7",
+		.pin = {
+			.gpio = AT91_PIN_PC18,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "led-sig2",
+		},
+		.active_low = 1,
+	},
+	{
+		.name = "LED7",
+		.pin = {
+			.gpio = AT91_PIN_PC18,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "led-e",
+		},
+		.active_low = 1,
+	},
+	{
+		.name = "LED8",
+		.pin = {
+			.gpio = AT91_PIN_PC17,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "led-sig3",
+		},
+		.active_low = 1,
+	},
+	{
+		.name = "LED8",
+		.pin = {
+			.gpio = AT91_PIN_PC17,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "led-f",
+		},
+		.active_low = 1,
+	},
+	{
+		.name = "RI_B",
+		.pin = {
+			.gpio = AT91_PIN_PC25,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "extserial-ri",
+		},
+		.active_low = 1,
+	},
+	{
+		.name = "DTR_B",
+		.pin = {
+			.gpio = AT91_PIN_PC26,
+			.flags = GPIOF_IN,
+			.label = "extserial-dtr",
+		},
+		.active_low = 1,
+	},
+	{
+		.name = "DSR_B",
+		.pin = {
+			.gpio = AT91_PIN_PC27,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "extserial-dsr",
+		},
+		.active_low = 1,
+	},
+	{
+		.name = "DCD_B",
+		.pin = {
+			.gpio = AT91_PIN_PC28,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "extserial-dcd",
+		},
+		.active_low = 1,
+	},
+
+	// The difference between MTRv1_0_0 and MTRv1_0_1 starts here
+	{
+		.name = "WIFI_BT_ULPWKUP",
+		.pin = {
+			.gpio = AT91_PIN_PA0,
+			.flags = GPIOF_IN,
+			.label = "wifi-bt-ulpwkup",
+		}
+	},
+	{
+		.name = "WIFI_BT_LPWKUP",
+		.pin = {
+			.gpio = AT91_PIN_PA6,
+			.flags = GPIOF_IN,
+			.label = "wifi-bt-lpwkup",
+		}
+	},
+	{
+		.name = "WIFI_BT_INT",
+		.pin = {
+			.gpio = AT91_PIN_PB11,
+			.flags = GPIOF_IN,
+			.label = "wifi-bt-int",
+		}
+	},
+	{
+		.name = "WIFI_BT_RESET",
+		.pin = {
+			.gpio = AT91_PIN_PD14,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "wifi-bt-reset",
+		}
+	},
+	{
+		.name = "WIFI_BT_LPMODE",
+		.pin = {
+			.gpio = AT91_PIN_PD20,
+			.flags = GPIOF_IN,
+			.label = "wifi-bt-lpmode",
+		}
+	},
+	{
+		.name = "GNSS_RESET",
+		.pin = {
+			.gpio = AT91_PIN_PD15,
+			.flags = GPIOF_OUT_INIT_LOW,
+			.label = "gnss-reset",
+		}
+	},
+	{
+		.name = "SECURE_RESET",
+		.pin = {
+			.gpio = AT91_PIN_PD16,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "secure-reset",
+		}
+	},
+	{
+		.name = "USBHUB_RESET",
+		.pin = {
+			.gpio = AT91_PIN_PD18,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "usbhub-reset",
+		}
+	},
+	{
+		.name = "GNSS_INT",
+		.pin = {
+			.gpio = AT91_PIN_PD19,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "gnss-int",
+		}
+	},
+
+
+	{ },
+};
+
+static struct gpio_pin gpio_pins_mtrv1_0_2[] = {
+	{
+		.name = "ETH_RESET",
+		.pin = {
+			.gpio = AT91_PIN_PC6,
+			.flags = GPIOF_OUT_INIT_HIGH | GPIOF_OPEN_DRAIN,  /* without GPIOF_OPEN_DRAIN causes issues with the Micrel KSZ8091RNBCA (RMII) PHY */
+			.label = "eth-reset",
+		},
+		.active_low = 0,
+	},
+	{
+		.name = "RADIO_POWER_MONITOR",
+		.pin = {
+			.gpio = AT91_PIN_PA23,
+			.flags = GPIOF_IN,
+			.label = "radio-power-monitor",
+		},
+		.active_low = 0,
+	},
+	{
+		.name = "RADIO_RESET",
+		.pin = {
+			.gpio = AT91_PIN_PA22,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "radio-reset",
+		},
+		.active_low = 0,
+	},
+	{
+		.name = "RADIO_POWER",
+		.pin = {
+			.gpio = AT91_PIN_PA21,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "radio-power",
+		},
+		.active_low = 0,
+	},
+	{
+		.name = "DEVICE_RESET",
+		.pin = {
+			.gpio = AT91_PIN_PC4,
+			.flags = GPIOF_IN,
+			.label = "reset",
+		},
+		.active_low = 1,
+	},
+	{
+		.name = "LS_LED",
+		.pin = {
+			.gpio = AT91_PIN_PC4,
+#if LED_LS_CONTROLLABLE
+			.flags = GPIOF_OUT_INIT_HIGH,
+#else
+			.flags = GPIOF_IN,
+#endif
+			.label = "led-ls",
+		},
+		.active_low = 1,
+	},
+	{
+		.name = "STATUS_LED",
+		.pin = {
+			.gpio = AT91_PIN_PC21,
+			.flags = GPIOF_OUT_INIT_LOW,
+			.label = "led-status",
+		},
+		.active_low = 1,
+	},
+	{
+		.name = "LED3",
+		.pin = {
+			.gpio = AT91_PIN_PC15,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "led-wifi",
+		},
+		.active_low = 1,
+	},
+	{
+		.name = "LED3",
+		.pin = {
+			.gpio = AT91_PIN_PC15,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "led-b",
+		},
+		.active_low = 1,
+	},
+	{
+		.name = "LED4",
+		.pin = {
+			.gpio = AT91_PIN_PC20,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "led-cd",
+		},
+		.active_low = 1,
+	},
+	{
+		.name = "LED4",
+		.pin = {
+			.gpio = AT91_PIN_PC20,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "led-c",
+		},
+		.active_low = 1,
+	},
+	{
+		.name = "LED6",
+		.pin = {
+			.gpio = AT91_PIN_PC19,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "led-sig1",
+		},
+		.active_low = 1,
+	},
+	{
+		.name = "LED6",
+		.pin = {
+			.gpio = AT91_PIN_PC19,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "led-d",
+		},
+		.active_low = 1,
+	},
+	{
+		.name = "LED7",
+		.pin = {
+			.gpio = AT91_PIN_PC18,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "led-sig2",
+		},
+		.active_low = 1,
+	},
+	{
+		.name = "LED7",
+		.pin = {
+			.gpio = AT91_PIN_PC18,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "led-e",
+		},
+		.active_low = 1,
+	},
+	{
+		.name = "LED8",
+		.pin = {
+			.gpio = AT91_PIN_PC17,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "led-sig3",
+		},
+		.active_low = 1,
+	},
+	{
+		.name = "LED8",
+		.pin = {
+			.gpio = AT91_PIN_PC17,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "led-f",
+		},
+		.active_low = 1,
+	},
+	{
+		.name = "RI_B",
+		.pin = {
+			.gpio = AT91_PIN_PC25,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "extserial-ri",
+		},
+		.active_low = 1,
+	},
+	{
+		.name = "DTR_B",
+		.pin = {
+			.gpio = AT91_PIN_PC26,
+			.flags = GPIOF_IN,
+			.label = "extserial-dtr",
+		},
+		.active_low = 1,
+	},
+	{
+		.name = "DSR_B",
+		.pin = {
+			.gpio = AT91_PIN_PC27,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "extserial-dsr",
+		},
+		.active_low = 1,
+	},
+	{
+		.name = "DCD_B",
+		.pin = {
+			.gpio = AT91_PIN_PC28,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "extserial-dcd",
+		},
+		.active_low = 1,
+	},
+
+	// The difference between MTRv1_0_0 and MTRv1_0_1 starts here
+	{
+		.name = "WIFI_BT_ULPWKUP",
+		.pin = {
+			.gpio = AT91_PIN_PA0,
+			.flags = GPIOF_IN,
+			.label = "wifi-bt-ulpwkup",
+		}
+	},
+	{
+		.name = "WIFI_BT_LPWKUP",
+		.pin = {
+			.gpio = AT91_PIN_PA6,
+			.flags = GPIOF_IN,
+			.label = "wifi-bt-lpwkup",
+		}
+	},
+	{
+		.name = "WIFI_BT_INT",
+		.pin = {
+			.gpio = AT91_PIN_PB11,
+			.flags = GPIOF_IN,
+			.label = "wifi-bt-int",
+		}
+	},
+	{
+		.name = "WIFI_BT_RESET",
+		.pin = {
+			.gpio = AT91_PIN_PD14,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "wifi-bt-reset",
+		}
+	},
+	{
+		.name = "WIFI_BT_LPMODE",
+		.pin = {
+			.gpio = AT91_PIN_PD20,
+			.flags = GPIOF_IN,
+			.label = "wifi-bt-lpmode",
+		}
+	},
+	{
+		.name = "GNSS_RESET",
+		.pin = {
+			.gpio = AT91_PIN_PD15,
+			.flags = GPIOF_OUT_INIT_LOW,
+			.label = "gnss-reset",
+		}
+	},
+	{
+		.name = "SECURE_RESET",
+		.pin = {
+			.gpio = AT91_PIN_PD16,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "secure-reset",
+		}
+	},
+	{
+		.name = "USBHUB_RESET",
+		.pin = {
+			.gpio = AT91_PIN_PD18,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "usbhub-reset",
+		}
+	},
+	{
+		.name = "GNSS_INT",
+		.pin = {
+			.gpio = AT91_PIN_PD19,
+			.flags = GPIOF_OUT_INIT_HIGH,
+			.label = "gnss-int",
+		}
+	},
+        // Difference with mtrv1_0_1 starts here
+        {
+                .name = "RADIO_WM_LK_M",  // WM LINK Monitor for CAT M
+                .pin = {
+                        .gpio = AT91_PIN_PA14,
+			.flags = GPIOF_IN,
+			.label = "radio-wm-lk-m",
+		}
+	},
+
+	{ },
+};
+
+static struct gpio_pin gpio_pins_mtrv1_0_3[] = {
+       {
+               .name = "ETH_RESET",
+               .pin = {
+                       .gpio = AT91_PIN_PC6,
+                       .flags = GPIOF_OUT_INIT_HIGH | GPIOF_OPEN_DRAIN,  /* without GPIOF_OPEN_DRAIN causes issues with the Micrel KSZ8091RNBCA (RMII) PHY */
+                       .label = "eth-reset",
+               },
+               .active_low = 0,
+       },
+       {
+               .name = "DEVICE_RESET",
+               .pin = {
+                       .gpio = AT91_PIN_PC4,
+                       .flags = GPIOF_IN,
+                       .label = "reset",
+               },
+               .active_low = 1,
+       },
+       {
+               .name = "LS_LED",
+               .pin = {
+                       .gpio = AT91_PIN_PC4,
+#if LED_LS_CONTROLLABLE
+                       .flags = GPIOF_OUT_INIT_HIGH,
+#else
+                       .flags = GPIOF_IN,
+#endif
+                       .label = "led-ls",
+               },
+               .active_low = 1,
+       },
+       {
+               .name = "STATUS_LED",
+               .pin = {
+                       .gpio = AT91_PIN_PC21,
+                       .flags = GPIOF_OUT_INIT_LOW,
+                       .label = "led-status",
+               },
+               .active_low = 1,
+       },
+       {
+               .name = "LED3",
+               .pin = {
+                       .gpio = AT91_PIN_PC15,
+                       .flags = GPIOF_OUT_INIT_HIGH,
+                       .label = "led-wifi",
+               },
+               .active_low = 1,
+       },
+       {
+               .name = "LED3",
+               .pin = {
+                       .gpio = AT91_PIN_PC15,
+                       .flags = GPIOF_OUT_INIT_HIGH,
+                       .label = "led-b",
+               },
+               .active_low = 1,
+       },
+       {
+               .name = "LED4",
+               .pin = {
+                       .gpio = AT91_PIN_PC20,
+                       .flags = GPIOF_OUT_INIT_HIGH,
+                       .label = "led-cd",
+               },
+               .active_low = 1,
+       },
+       {
+               .name = "LED4",
+               .pin = {
+                       .gpio = AT91_PIN_PC20,
+                       .flags = GPIOF_OUT_INIT_HIGH,
+                       .label = "led-c",
+               },
+               .active_low = 1,
+       },
+       {
+               .name = "LED6",
+               .pin = {
+                       .gpio = AT91_PIN_PC19,
+                       .flags = GPIOF_OUT_INIT_HIGH,
+                       .label = "led-sig1",
+               },
+               .active_low = 1,
+       },
+       {
+               .name = "LED6",
+               .pin = {
+                       .gpio = AT91_PIN_PC19,
+                       .flags = GPIOF_OUT_INIT_HIGH,
+                       .label = "led-d",
+               },
+               .active_low = 1,
+       },
+       {
+               .name = "LED7",
+               .pin = {
+                       .gpio = AT91_PIN_PC18,
+                       .flags = GPIOF_OUT_INIT_HIGH,
+                       .label = "led-sig2",
+               },
+               .active_low = 1,
+       },
+       {
+               .name = "LED7",
+               .pin = {
+                       .gpio = AT91_PIN_PC18,
+                       .flags = GPIOF_OUT_INIT_HIGH,
+                       .label = "led-e",
+               },
+               .active_low = 1,
+       },
+       {
+               .name = "LED8",
+               .pin = {
+                       .gpio = AT91_PIN_PC17,
+                       .flags = GPIOF_OUT_INIT_HIGH,
+                       .label = "led-sig3",
+               },
+               .active_low = 1,
+       },
+       {
+               .name = "LED8",
+               .pin = {
+                       .gpio = AT91_PIN_PC17,
+                       .flags = GPIOF_OUT_INIT_HIGH,
+                       .label = "led-f",
+               },
+               .active_low = 1,
+       },
+       {
+               .name = "RI_B",
+               .pin = {
+                       .gpio = AT91_PIN_PC25,
+                       .flags = GPIOF_OUT_INIT_HIGH,
+                       .label = "extserial-ri",
+               },
+               .active_low = 1,
+       },
+       {
+               .name = "DTR_B",
+               .pin = {
+                       .gpio = AT91_PIN_PC26,
+                       .flags = GPIOF_IN,
+                       .label = "extserial-dtr",
+               },
+               .active_low = 1,
+       },
+       {
+               .name = "DSR_B",
+               .pin = {
+                       .gpio = AT91_PIN_PC27,
+                       .flags = GPIOF_OUT_INIT_HIGH,
+                       .label = "extserial-dsr",
+               },
+               .active_low = 1,
+       },
+       {
+               .name = "DCD_B",
+               .pin = {
+                       .gpio = AT91_PIN_PC28,
+                       .flags = GPIOF_OUT_INIT_HIGH,
+                       .label = "extserial-dcd",
+               },
+               .active_low = 1,
+       },
+
+       // The difference between MTRv1_0_0 and MTRv1_0_1 starts here
+      {
+               .name = "WIFI_BT_ULPWKUP",
+               .pin = {
+                       .gpio = AT91_PIN_PA0,
+                       .flags = GPIOF_IN,
+                       .label = "wifi-bt-ulpwkup",
+               }
+       },
+      {
+               .name = "WIFI_BT_LPWKUP",
+               .pin = {
+                       .gpio = AT91_PIN_PA6,
+                       .flags = GPIOF_IN,
+                       .label = "wifi-bt-lpwkup",
+               }
+       },
+       {
+               .name = "WIFI_BT_INT",
+               .pin = {
+                       .gpio = AT91_PIN_PB11,
+                       .flags = GPIOF_IN,
+                       .label = "wifi-bt-int",
+               }
+       },
+       {
+               .name = "WIFI_BT_RESET",
+               .pin = {
+                       .gpio = AT91_PIN_PD14,
+                       .flags = GPIOF_OUT_INIT_HIGH,
+                       .label = "wifi-bt-reset",
+               }
+       },
+       {
+               .name = "WIFI_BT_LPMODE",
+               .pin = {
+                       .gpio = AT91_PIN_PD20,
+                       .flags = GPIOF_IN,
+                       .label = "wifi-bt-lpmode",
+               }
+       },
+       {
+               .name = "GNSS_RESET",
+               .pin = {
+                       .gpio = AT91_PIN_PD15,
+                       .flags = GPIOF_OUT_INIT_LOW,
+                       .label = "gnss-reset",
+               }
+       },
+       {
+               .name = "SECURE_RESET",
+               .pin = {
+                       .gpio = AT91_PIN_PD16,
+                       .flags = GPIOF_OUT_INIT_HIGH,
+                       .label = "secure-reset",
+               }
+       },
+       {
+               .name = "MTQ_RESET",
+               .pin = {
+                       .gpio = AT91_PIN_PD17,
+                       .flags = GPIOF_OUT_INIT_HIGH,
+                       .label = "radio-reset",
+               }
+       },
+       {
+               .name = "USBHUB_RESET",
+               .pin = {
+                       .gpio = AT91_PIN_PD18,
+                       .flags = GPIOF_OUT_INIT_HIGH,
+                       .label = "usbhub-reset",
+               }
+       },
+       {
+               .name = "GNSS_INT",
+               .pin = {
+                       .gpio = AT91_PIN_PD19,
+                       .flags = GPIOF_OUT_INIT_HIGH,
+                       .label = "gnss-int",
+               }
+       },
+        // Difference with mtrv1_0_1 starts here
+        {
+                .name = "RADIO_WM_LK_M",  // WM LINK Monitor for CAT M
+                .pin = {
+                        .gpio = AT91_PIN_PA14,
+                       .flags = GPIOF_IN,
+                       .label = "radio-wm-lk-m",
+               }
+       },
+
+       { },
+};
+
+/* radio control (power/reset) for mtr */
+static int radio_off_mtr(void)
+{
+	int value;
+	struct gpio_pin *pwrmon_pin = gpio_pin_by_attr_name("radio-power-monitor");
+	struct gpio_pin *onoff_pin = gpio_pin_by_attr_name("radio-power");
+	struct gpio_pin *rst_pin = gpio_pin_by_attr_name("radio-reset");
+
+	if (!onoff_pin || !pwrmon_pin || !rst_pin) {
+		return -ENODEV;
+	}
+
+	value = gpio_get_value(pwrmon_pin->pin.gpio);
+	if(value == 0) {
+		log_error("radio is already off");
+		return -EINVAL;
+	}
+
+	// drive on/off pin low for at least 3 sec
+	log_info("shutting down radio");
+	gpio_set_value(onoff_pin->pin.gpio, 0);
+
+	msleep(3500);
+
+	// set on/off pin high
+	gpio_set_value(onoff_pin->pin.gpio, 1);
+
+	msleep(200);
+
+	// check that power is low
+	value = gpio_get_value(pwrmon_pin->pin.gpio);
+	if(value != 0) {
+		log_warning("radio is still on. performing radio reset.");
+		//Perform Hard Reset
+		gpio_set_value(rst_pin->pin.gpio, 0);
+
+		msleep(500);
+
+		// set pin high
+		gpio_set_value(rst_pin->pin.gpio, 1);
+	} else {
+		log_info("radio has been shut down");
+	}
+
+	return 0;
+}
+
+static int radio_on_mtr(void)
+{
+	int value;
+	struct gpio_pin *pwrmon_pin = gpio_pin_by_attr_name("radio-power-monitor");
+	struct gpio_pin *onoff_pin = gpio_pin_by_attr_name("radio-power");
+	struct gpio_pin *rst_pin = gpio_pin_by_attr_name("radio-reset");
+
+	if (!onoff_pin || !pwrmon_pin || !rst_pin) {
+		return -ENODEV;
+	}
+
+	value = gpio_get_value(pwrmon_pin->pin.gpio);
+	if(value != 0) {
+		log_error("radio is already on");
+		return -EINVAL;
+	}
+
+	// drive on/off pin low for at least 5 sec
+	log_info("turning on radio");
+	gpio_set_value(onoff_pin->pin.gpio, 0);
+
+	msleep(5500);
+
+	// set on/off pin high
+	gpio_set_value(onoff_pin->pin.gpio, 1);
+
+	msleep(200);
+
+	// check that power is high
+	value = gpio_get_value(pwrmon_pin->pin.gpio);
+	if(value == 0) {
+		log_warning("radio is still off. performing radio reset");
+		//Perform Hard Reset
+		gpio_set_value(rst_pin->pin.gpio, 0);
+
+		msleep(500);
+
+		// set pin high
+		gpio_set_value(rst_pin->pin.gpio, 1);
+	} else {
+		log_info("radio has been turned on");
+	}
+
+	return 0;
+}
+
+static int radio_reset_mtr(void)
+{
+	struct gpio_pin *onoff_pin = gpio_pin_by_attr_name("radio-power");
+	struct gpio_pin *rst_pin = gpio_pin_by_attr_name("radio-reset");
+
+	if (!rst_pin || !onoff_pin) {
+		return -ENODEV;
+	}
+
+	// drive reset pin low for 500ms
+	gpio_set_value(rst_pin->pin.gpio, 0);
+
+	msleep(500);
+
+	// set pin high
+	gpio_set_value(rst_pin->pin.gpio, 1);
+
+	// wait for 2 sec before toggling on/off pin
+	msleep(2000);
+
+	// drive on/off pin low for 6 sec
+	gpio_set_value(onoff_pin->pin.gpio, 0);
+
+	msleep(6000);
+
+	// set on/off pin high
+	gpio_set_value(onoff_pin->pin.gpio, 1);
+	return 0;
+}
+
+static int radio_reset_mtr_mtq(void)
+{
+	struct gpio_pin *rst_pin = gpio_pin_by_attr_name("radio-reset");
+
+	if (!rst_pin) {
+		return -ENODEV;
+	}
+
+	// drive reset pin low for 500ms
+	gpio_set_value(rst_pin->pin.gpio, 0);
+
+	msleep(500);
+
+	// set pin high
+	gpio_set_value(rst_pin->pin.gpio, 1);
+
+	// wait for 2 sec before toggling on/off pin
+	msleep(2000);
+
+	return 0;
+}
+
+static ssize_t mts_attr_store_radio_power_mtr(struct device *dev,
+		struct device_attribute *attr, const char *buf, size_t count)
+{
+	int value;
+	int err;
+
+	if (sscanf(buf, "%i", &value) != 1) {
+		return -EINVAL;
+	}
+	if (value == 0) {
+		mutex_lock(&mts_io_mutex);
+		err = radio_off_mtr();
+		mutex_unlock(&mts_io_mutex);
+	} else {
+		mutex_lock(&mts_io_mutex);
+		err = radio_on_mtr();
+		mutex_unlock(&mts_io_mutex);
+	}
+
+	if (err) {
+		return err;
+	}
+
+	return count;
+}
+
+static ssize_t mts_attr_store_radio_reset_mtr(struct device *dev,
+		struct device_attribute *attr, const char *buf, size_t count)
+{
+	int value; /* 0 = normal reset; -1 = forced reset */
+	int err;
+
+	if (sscanf(buf, "%i", &value) != 1) {
+		return -EINVAL;
+	}
+	if (value != 0 && value != -1) {
+		return -EINVAL;
+	}
+
+	/* check reset timings is enabled */
+	if (value != -1 && NULL != timings_data) {
+		/* check reset timer is started */
+		if (radio_reset_timer_is_start == 1) {
+			log_info("radio reset timer is running. \n");
+			return count;
+		}
+
+		/* check reset timer available is started */
+		if (radio_reset_available_timer_is_start == 1) {
+			del_timer(&radio_reset_available_timer);
+			radio_reset_available_timer_is_start = 0;
+		}
+
+		/* reset timer not started, start it */
+		mod_timer(&radio_reset_timer, jiffies + msecs_to_jiffies((timings_data[timings_data_index]) * 1000));
+		//log_info("radio reset timer is start = [%d]\n", time_now_secs());
+		/* save timings_data_stop_seconds */
+		timings_data_stop_seconds = timings_data[timings_data_index] + time_now_secs();
+		radio_reset_timer_is_start = 1;
+	}
+
+	log_info("radio is reset\n");
+
+	mutex_lock(&mts_io_mutex);
+
+	if (mts_hw_version == MTRV1_0_3)
+	{
+        err = radio_reset_mtr_mtq();
+	}
+	else
+	{
+	    err = radio_reset_mtr();
+	}
+
+
+	mutex_unlock(&mts_io_mutex);
+
+	if (err) {
+		return err;
+	}
+
+	return count;
+}
+
+static ssize_t mts_attr_show_radio_power(struct device *dev,
+			struct device_attribute *attr, char *buf)
+{
+	int value;
+	struct gpio_pin *pwrmon_pin = gpio_pin_by_attr_name("radio-power-monitor");
+
+	if ( !pwrmon_pin ) {
+		return -ENODEV;
+	}
+
+	value = gpio_get_value(pwrmon_pin->pin.gpio);
+	return sprintf(buf, "%d\n", value);
+}
+
+static DEVICE_ATTR_MTS(dev_attr_radio_power_mtr, "radio-power",
+	mts_attr_show_radio_power, mts_attr_store_radio_power_mtr);
+
+static DEVICE_ATTR_MTS(dev_attr_radio_reset_mtr, "radio-reset",
+	mts_attr_show_gpio_pin, mts_attr_store_radio_reset_mtr);
+
+static DEVICE_ATTR_MTS(dev_attr_eth_reset_mtr, "eth-reset",
+	mts_attr_show_gpio_pin, mts_attr_store_gpio_pin);
+
+static DEVICE_ATTR_MTS(dev_attr_bt_enabled_mtr, "bt-enabled",
+	mts_attr_show_gpio_pin, mts_attr_store_gpio_pin);
+
+static DEVICE_ATTR_MTS(dev_attr_wlan_enabled_mtr, "wlan-enabled",
+	mts_attr_show_gpio_pin, mts_attr_store_gpio_pin);
+
+static DEVICE_ATTR_MTS(dev_attr_led_wifi_gpio_mtr, "led-wifi",
+	mts_attr_show_gpio_pin, mts_attr_store_gpio_pin);
+
+static DEVICE_ATTR_MTS(dev_attr_led_f_gpio_mtr, "led-f",
+	mts_attr_show_gpio_pin, mts_attr_store_gpio_pin);
+
+static DEVICE_ATTR_MTS(dev_attr_extserial_ri_gpio_mtr, "extserial-ri",
+	mts_attr_show_gpio_pin, mts_attr_store_gpio_pin);
+
+static DEVICE_ATTR_RO_MTS(dev_attr_extserial_dtr_mtr, "extserial-dtr",
+	mts_attr_show_gpio_pin);
+
+static DEVICE_ATTR_MTS(dev_attr_extserial_dsr_gpio_mtr, "extserial-dsr",
+	mts_attr_show_gpio_pin, mts_attr_store_gpio_pin);
+
+static DEVICE_ATTR_MTS(dev_attr_extserial_dcd_gpio_mtr, "extserial-dcd",
+	mts_attr_show_gpio_pin, mts_attr_store_gpio_pin);
+
+static DEVICE_ATTR_RO_MTS(dev_attr_wifi_mac_mtr, "mac-wifi",
+	mts_attr_show_product_info);
+
+static DEVICE_ATTR_RO_MTS(dev_attr_bluetooth_mac_mtr, "mac-bluetooth",
+	mts_attr_show_product_info);
+
+static DEVICE_ATTR_MTS(dev_attr_wifi_bt_lpwkup_mtr, "wifi-bt-lpwkup",
+	mts_attr_show_gpio_pin, mts_attr_store_gpio_pin);
+
+static DEVICE_ATTR_MTS(dev_attr_wifi_bt_ulpwkup_mtr, "wifi-bt-ulpwkup",
+	mts_attr_show_gpio_pin, mts_attr_store_gpio_pin);
+
+static DEVICE_ATTR_MTS(dev_attr_wifi_bt_reset_mtr, "wifi-bt-reset",
+	mts_attr_show_gpio_pin, mts_attr_store_gpio_pin);
+
+static DEVICE_ATTR_RO_MTS(dev_attr_wifi_bt_lpmode_mtr, "wifi-bt-lpmode",
+	mts_attr_show_gpio_pin);
+
+static DEVICE_ATTR_RO_MTS(dev_attr_wifi_bt_int_mtr, "wifi-bt-int",
+	mts_attr_show_gpio_pin);
+
+static DEVICE_ATTR_MTS(dev_attr_gnss_reset_mtr, "gnss-reset",
+	mts_attr_show_gpio_pin, mts_attr_store_gpio_pin);
+
+static DEVICE_ATTR_MTS(dev_attr_usbhub_reset_mtr, "usbhub-reset",
+	mts_attr_show_gpio_pin, mts_attr_store_gpio_pin);
+
+static DEVICE_ATTR_RO_MTS(dev_attr_gnss_int_mtr, "gnss-int",
+	mts_attr_show_gpio_pin);
+
+static DEVICE_ATTR_RO_MTS(dev_attr_radio_wm_lk_m, "radio-wm-lk-m",
+	mts_attr_show_gpio_pin);
+
+
+static struct attribute *mtr_platform_attributes[] = {
+	&dev_attr_vendor_id.attr,
+	&dev_attr_product_id.attr,
+	&dev_attr_device_id.attr,
+	&dev_attr_uuid.attr,
+	&dev_attr_hw_version.attr,
+	&dev_attr_imei.attr,
+	&dev_attr_eth_mac.attr,
+	&dev_attr_has_radio.attr,
+	&dev_attr_wifi_mac_mtr.attr,
+	&dev_attr_bluetooth_mac_mtr.attr,
+	&dev_attr_reset.attr,
+	&dev_attr_reset_monitor.attr,
+	&dev_attr_reset_monitor_intervals.attr,
+
+	&dev_attr_extserial_ri_gpio_mtr.attr,
+	&dev_attr_extserial_dtr_mtr.attr,
+	&dev_attr_extserial_dsr_gpio_mtr.attr,
+	&dev_attr_extserial_dcd_gpio_mtr.attr,
+
+	&dev_attr_eth_reset_mtr.attr,
+	&dev_attr_bt_enabled_mtr.attr,
+	&dev_attr_wlan_enabled_mtr.attr,
+
+	&dev_attr_led_status.attr,
+	&dev_attr_led_cd_gpio.attr,
+	&dev_attr_led_sig1_gpio.attr,
+	&dev_attr_led_sig2_gpio.attr,
+	&dev_attr_led_sig3_gpio.attr,
+	&dev_attr_led_wifi_gpio_mtr.attr,
+
+	//&dev_attr_led_a_gpio.attr,
+	&dev_attr_led_b_gpio.attr,
+	&dev_attr_led_c_gpio.attr,
+	&dev_attr_led_d_gpio.attr,
+	&dev_attr_led_e_gpio.attr,
+	&dev_attr_led_f_gpio_mtr.attr,
+
+	/* Radio stuff moved to end for possible removal */
+	&dev_attr_radio_power_mtr.attr,  /* radio_power must be first */
+	&dev_attr_radio_reset_mtr.attr,
+
+	&dev_attr_radio_reset_backoffs.attr,
+	&dev_attr_radio_reset_backoff_index.attr,
+	&dev_attr_radio_reset_backoff_seconds.attr,
+
+	NULL,
+};
+
+static struct attribute_group mtr_platform_attribute_group = {
+	.attrs = mtr_platform_attributes
+};
+
+
+static struct attribute *mtrv1_0_1_platform_attributes[] = {
+	&dev_attr_vendor_id.attr,
+	&dev_attr_product_id.attr,
+	&dev_attr_device_id.attr,
+	&dev_attr_uuid.attr,
+	&dev_attr_hw_version.attr,
+	&dev_attr_imei.attr,
+	&dev_attr_eth_mac.attr,
+	&dev_attr_has_radio.attr,
+	&dev_attr_wifi_mac_mtr.attr,
+        &dev_attr_bluetooth_mac_mtr.attr,
+
+	&dev_attr_reset.attr,
+	&dev_attr_reset_monitor.attr,
+	&dev_attr_reset_monitor_intervals.attr,
+	&dev_attr_radio_power_mtr.attr,
+	&dev_attr_radio_reset_mtr.attr,
+
+	&dev_attr_radio_reset_backoffs.attr,
+	&dev_attr_radio_reset_backoff_index.attr,
+	&dev_attr_radio_reset_backoff_seconds.attr,
+
+	&dev_attr_extserial_ri_gpio_mtr.attr,
+	&dev_attr_extserial_dtr_mtr.attr,
+	&dev_attr_extserial_dsr_gpio_mtr.attr,
+	&dev_attr_extserial_dcd_gpio_mtr.attr,
+
+	&dev_attr_eth_reset_mtr.attr,
+	&dev_attr_wifi_bt_lpwkup_mtr.attr,
+	&dev_attr_wifi_bt_ulpwkup_mtr.attr,
+	&dev_attr_wifi_bt_reset_mtr.attr,
+	&dev_attr_wifi_bt_lpmode_mtr.attr,
+	&dev_attr_wifi_bt_int_mtr.attr,
+	&dev_attr_gnss_reset_mtr.attr,
+	&dev_attr_usbhub_reset_mtr.attr,
+	&dev_attr_gnss_int_mtr.attr,
+
+	&dev_attr_led_status.attr,
+	&dev_attr_led_cd_gpio.attr,
+	&dev_attr_led_sig1_gpio.attr,
+	&dev_attr_led_sig2_gpio.attr,
+	&dev_attr_led_sig3_gpio.attr,
+	&dev_attr_led_wifi_gpio_mtr.attr,
+
+	&dev_attr_led_b_gpio.attr,
+	&dev_attr_led_c_gpio.attr,
+	&dev_attr_led_d_gpio.attr,
+	&dev_attr_led_e_gpio.attr,
+	&dev_attr_led_f_gpio_mtr.attr,
+
+	NULL,
+};
+
+static struct attribute_group mtrv1_0_1_platform_attribute_group = {
+	.attrs = mtrv1_0_1_platform_attributes
+};
+
+static struct attribute *mtrv1_0_2_platform_attributes[] = {
+	&dev_attr_vendor_id.attr,
+	&dev_attr_product_id.attr,
+	&dev_attr_device_id.attr,
+	&dev_attr_uuid.attr,
+	&dev_attr_hw_version.attr,
+	&dev_attr_imei.attr,
+	&dev_attr_eth_mac.attr,
+	&dev_attr_has_radio.attr,
+	&dev_attr_wifi_mac_mtr.attr,
+	&dev_attr_bluetooth_mac_mtr.attr,
+
+	&dev_attr_reset.attr,
+	&dev_attr_reset_monitor.attr,
+	&dev_attr_reset_monitor_intervals.attr,
+	&dev_attr_radio_power_mtr.attr,
+	&dev_attr_radio_reset_mtr.attr,
+
+	&dev_attr_radio_reset_backoffs.attr,
+	&dev_attr_radio_reset_backoff_index.attr,
+	&dev_attr_radio_reset_backoff_seconds.attr,
+        
+	&dev_attr_extserial_ri_gpio_mtr.attr,
+	&dev_attr_extserial_dtr_mtr.attr,
+	&dev_attr_extserial_dsr_gpio_mtr.attr,
+	&dev_attr_extserial_dcd_gpio_mtr.attr,
+
+	&dev_attr_eth_reset_mtr.attr,
+	&dev_attr_wifi_bt_lpwkup_mtr.attr,
+	&dev_attr_wifi_bt_ulpwkup_mtr.attr,
+	&dev_attr_wifi_bt_reset_mtr.attr,
+	&dev_attr_wifi_bt_lpmode_mtr.attr,
+	&dev_attr_wifi_bt_int_mtr.attr,
+	&dev_attr_gnss_reset_mtr.attr,
+	&dev_attr_usbhub_reset_mtr.attr,
+	&dev_attr_gnss_int_mtr.attr,
+
+	&dev_attr_led_status.attr,
+	&dev_attr_led_cd_gpio.attr,
+	&dev_attr_led_sig1_gpio.attr,
+	&dev_attr_led_sig2_gpio.attr,
+	&dev_attr_led_sig3_gpio.attr,
+	&dev_attr_led_wifi_gpio_mtr.attr,
+
+	&dev_attr_led_b_gpio.attr,
+	&dev_attr_led_c_gpio.attr,
+	&dev_attr_led_d_gpio.attr,
+	&dev_attr_led_e_gpio.attr,
+	&dev_attr_led_f_gpio_mtr.attr,
+
+        &dev_attr_radio_wm_lk_m.attr,  // CAT M feature
+       
+	NULL,
+};
+
+static struct attribute_group mtrv1_0_2_platform_attribute_group = {
+	.attrs = mtrv1_0_2_platform_attributes
+};
+
+
+static struct attribute *mtrv1_0_3_platform_attributes[] = {
+       &dev_attr_vendor_id.attr,
+       &dev_attr_product_id.attr,
+       &dev_attr_device_id.attr,
+       &dev_attr_uuid.attr,
+       &dev_attr_hw_version.attr,
+       &dev_attr_imei.attr,
+       &dev_attr_eth_mac.attr,
+       &dev_attr_has_radio.attr,
+       &dev_attr_wifi_mac_mtr.attr,
+       &dev_attr_bluetooth_mac_mtr.attr,
+
+       &dev_attr_reset.attr,
+       &dev_attr_reset_monitor.attr,
+       &dev_attr_reset_monitor_intervals.attr,
+       &dev_attr_radio_reset_mtr.attr,
+
+       &dev_attr_radio_reset_backoffs.attr,
+       &dev_attr_radio_reset_backoff_index.attr,
+       &dev_attr_radio_reset_backoff_seconds.attr,
+
+       &dev_attr_extserial_ri_gpio_mtr.attr,
+       &dev_attr_extserial_dtr_mtr.attr,
+       &dev_attr_extserial_dsr_gpio_mtr.attr,
+       &dev_attr_extserial_dcd_gpio_mtr.attr,
+
+       &dev_attr_eth_reset_mtr.attr,
+       &dev_attr_wifi_bt_lpwkup_mtr.attr,
+       &dev_attr_wifi_bt_ulpwkup_mtr.attr,
+       &dev_attr_wifi_bt_reset_mtr.attr,
+       &dev_attr_wifi_bt_lpmode_mtr.attr,
+       &dev_attr_wifi_bt_int_mtr.attr,
+       &dev_attr_gnss_reset_mtr.attr,
+       &dev_attr_usbhub_reset_mtr.attr,
+       &dev_attr_gnss_int_mtr.attr,
+
+       &dev_attr_led_status.attr,
+       &dev_attr_led_cd_gpio.attr,
+       &dev_attr_led_sig1_gpio.attr,
+       &dev_attr_led_sig2_gpio.attr,
+       &dev_attr_led_sig3_gpio.attr,
+       &dev_attr_led_wifi_gpio_mtr.attr,
+
+       &dev_attr_led_b_gpio.attr,
+       &dev_attr_led_c_gpio.attr,
+       &dev_attr_led_d_gpio.attr,
+       &dev_attr_led_e_gpio.attr,
+       &dev_attr_led_f_gpio_mtr.attr,
+
+    &dev_attr_radio_wm_lk_m.attr,  // CAT M feature?  Is this still there on the MTQ with Quectel?
+
+       NULL,
+};
+
+static struct attribute_group mtrv1_0_3_platform_attribute_group = {
+       .attrs = mtrv1_0_3_platform_attributes
+};