Age | Commit message (Expand) | Author | Files |
2019-07-03 | Set output low on the GNSS-RESET line | John Klug | 1 |
2019-07-03 | Add support to option driver for Quectel EG955.0.0 | Jeff Hatch | 2 |
2019-07-03 | GNSS reset fix to suppress GPS serial port to protect XR12V1414 from bad PID/VID | John Klug | 2 |
2019-07-03 | Bump the revision of the kernel for new device tree | John Klug | 1 |
2019-07-03 | Remove unused mmc pins, and put in PD14-PD20 in mtrv1 | John Klug | 1 |
2019-07-03 | Use output-high for MTCDT PD14-PD19 resets | John Klug | 1 |
2019-07-03 | Autoload i2c-dev for LoRa users | John Klug | 1 |
2019-07-03 | Remove unused mmc1-board | John Klug | 1 |
2019-07-03 | Syntax error in device tree | John Klug | 1 |
2019-07-03 | Missing semicolon in device tree. | John Klug | 1 |
2019-07-03 | Typo in name of patch for led brightness | John Klug | 1 |
2019-07-03 | Fix LED status on upgrade. | John Klug | 2 |
2019-07-03 | Correct the SDIO active pin to PA1, and set deglitch | John Klug | 1 |
2019-07-03 | Blink LEDs when kernel loads, not when modules load | John Klug | 2 |
2019-07-03 | Bump kernel revision for CGROUPS | John Klug | 1 |
2019-07-03 | Remove BLK_CGROUP and add PROC_EVENTS, and take the consequences from make me... | John Klug | 1 |
2019-07-03 | Make defconfig compatible with make menuconfig again. | John Klug | 1 |
2019-07-03 | All LTE MTR types can user B18 as the PPS signal | John Klug | 1 |
2019-07-03 | Change pps to pps-0 in device tree to allow for multiple entries. | John Klug | 1 |
2019-07-03 | Add rising edge IRQ to Murata - this is required for proper interrupt | Mike Nicholson | 1 |
2019-07-03 | Use timing from previous software iterations. | Mike Nicholson | 1 |
2019-07-03 | Enable/disable murata in wl12xx SDIO driver; deglitch, remove pull-down | Mike Nicholson | 3 |
2019-07-03 | Security enhancement (ASLR) : Disable CONFIG_COMPAT_BRK so that randomize_va_... | Jeff Hatch | 1 |
2019-07-03 | Make it clear why there are two PPS pins defined | John Klug | 1 |
2019-07-03 | Add PPS for MTRV1-0.0 and MTRV1-0.1 | John Klug | 1 |
2019-07-03 | Add the DT Overlay patch to kernel for MTRV1 | John Klug | 1 |
2019-07-03 | Add DMA to dbgu (not on uart0) | Mike Nicholson | 1 |
2019-07-03 | Add a couple jiffies of slack in the PMECCERRLOC | Mike Nicholson | 2 |
2019-07-03 | DMA for dbgu on MTCDT, and MTCAP (MTCAP requires testing) | Mike Nicholson | 2 |
2019-07-03 | Enable DMA on dbgu serial (fixes overrun issue) | Mike Nicholson | 1 |
2019-07-03 | Add DMA to uart0, delete m25p80 | Mike Nicholson | 1 |
2019-07-03 | Add mts-io/John's radio reset, remove m25p80, remove 16-bit nand, streamline ... | Mike Nicholson | 1 |
2019-07-03 | Use DMA for Venus on gps0/ttyS1, get Venus working | Mike Nicholson | 1 |
2019-07-03 | Pull down for radio monitor on mtrv1 | John Klug | 1 |
2019-07-03 | Original MTR, initial revision | Mike | 3 |
2019-07-03 | Pins must be set from a driver. Tie the radio pins to the MTS-IO driver. | John Klug | 1 |
2019-07-03 | PD21 should be pull down, remove conflicting unused NAND. | John Klug | 1 |
2019-07-03 | Add Telit Sprint patch for LXFP. | John Klug | 2 |
2019-07-03 | ledtrig-netdev patch for compatibility with old Multitech code | John Klug | 4 |
2019-07-03 | Bump the kernel and mts-io revision | John Klug | 1 |
2019-07-03 | Remove uneeded devices from device tree and get SPI working. | John Klug | 1 |
2019-07-03 | Remove unused m25p80 module. | John Klug | 1 |
2019-07-03 | Create device tree for mtcap, and move common patches to common | John Klug | 2 |
2019-07-03 | dma hangs GPS port. | John Klug | 3 |
2019-07-03 | Fix bitbake issues with machine variables and underscores | John Klug | 3 |
2019-07-03 | Change watchdog timer from 2 to 10 seconds to match old kernel. | John Klug | 2 |
2019-07-03 | Remove some of the dependent modules | John Klug | 2 |
2019-07-03 | Load tun, iptable-netfilter, ppp-generic at boot, and add more led module opt... | John Klug | 3 |
2019-07-03 | Put back Vizzini driver and install the kernel patch | John Klug | 2 |
2019-07-03 | Add *.inc files with modules to autoload on boot. | John Klug | 7 |