summaryrefslogtreecommitdiff
path: root/recipes-kernel/linux/linux-3.12.70/mtcdt/linux-3.12-mtcdt-device-tree.patch
diff options
context:
space:
mode:
Diffstat (limited to 'recipes-kernel/linux/linux-3.12.70/mtcdt/linux-3.12-mtcdt-device-tree.patch')
-rw-r--r--recipes-kernel/linux/linux-3.12.70/mtcdt/linux-3.12-mtcdt-device-tree.patch468
1 files changed, 0 insertions, 468 deletions
diff --git a/recipes-kernel/linux/linux-3.12.70/mtcdt/linux-3.12-mtcdt-device-tree.patch b/recipes-kernel/linux/linux-3.12.70/mtcdt/linux-3.12-mtcdt-device-tree.patch
deleted file mode 100644
index bea818d..0000000
--- a/recipes-kernel/linux/linux-3.12.70/mtcdt/linux-3.12-mtcdt-device-tree.patch
+++ /dev/null
@@ -1,468 +0,0 @@
-Index: linux-3.12.27/arch/arm/boot/dts/mtcdt.dts
-===================================================================
---- /dev/null 1970-01-01 00:00:00.000000000 +0000
-+++ linux-3.12.27/arch/arm/boot/dts/mtcdt.dts 2016-09-19 15:34:25.111103538 -0500
-@@ -0,0 +1,279 @@
-+/*
-+ * DTS file for Multi-Tech Systems MTCDT Hardware
-+ */
-+
-+/dts-v1/;
-+#include "at91sam9g25.dtsi"
-+#include "at91sam9x5ek.dtsi"
-+
-+/ {
-+ model = "Multi-Tech Systems MTCDT";
-+ compatible = "atmel,at91sam9g25ek", "atmel,at91sam9x5ek", "atmel,at91sam9x5", "atmel,at91sam9";
-+
-+ ahb {
-+ apb {
-+ macb0: ethernet@f802c000 {
-+ phy-mode = "rmii";
-+ status = "okay";
-+ };
-+
-+ pinctrl@fffff400 {
-+ nand {
-+ pinctrl_nand: nand-0 {
-+ atmel,pins =
-+ <AT91_PIOD 0 AT91_PERIPH_A AT91_PINCTRL_PULL_UP /* PD0 periph A Read Enable */
-+ AT91_PIOD 1 AT91_PERIPH_A AT91_PINCTRL_PULL_UP /* PD1 periph A Write Enable */
-+ AT91_PIOD 2 AT91_PERIPH_A AT91_PINCTRL_PULL_UP /* PD2 periph A Address Latch Enable */
-+ AT91_PIOD 3 AT91_PERIPH_A AT91_PINCTRL_PULL_UP /* PD3 periph A Command Latch Enable */
-+ AT91_PIOD 4 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP /* PD4 gpio Chip Enable pin pull_up */
-+ AT91_PIOC 31 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP /* PC31 gpio RDY/BUSY pin pull_up */
-+ AT91_PIOD 6 AT91_PERIPH_A AT91_PINCTRL_PULL_UP /* PD6 periph A Data bit 0 */
-+ AT91_PIOD 7 AT91_PERIPH_A AT91_PINCTRL_PULL_UP /* PD7 periph A Data bit 1 */
-+ AT91_PIOD 8 AT91_PERIPH_A AT91_PINCTRL_PULL_UP /* PD8 periph A Data bit 2 */
-+ AT91_PIOD 9 AT91_PERIPH_A AT91_PINCTRL_PULL_UP /* PD9 periph A Data bit 3 */
-+ AT91_PIOD 10 AT91_PERIPH_A AT91_PINCTRL_PULL_UP /* PD10 periph A Data bit 4 */
-+ AT91_PIOD 11 AT91_PERIPH_A AT91_PINCTRL_PULL_UP /* PD11 periph A Data bit 5 */
-+ AT91_PIOD 12 AT91_PERIPH_A AT91_PINCTRL_PULL_UP /* PD12 periph A Data bit 6 */
-+ AT91_PIOD 13 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>; /* PD13 periph A Data bit 7 */
-+ };
-+
-+ pinctrl_nand_16bits: nand_16bits-0 {
-+ atmel,pins =
-+ <AT91_PIOD 14 AT91_PERIPH_A AT91_PINCTRL_PULL_UP /* PD14 periph A Data bit 8 */
-+ AT91_PIOD 15 AT91_PERIPH_A AT91_PINCTRL_PULL_UP /* PD15 periph A Data bit 9 */
-+ AT91_PIOD 16 AT91_PERIPH_A AT91_PINCTRL_PULL_UP /* PD16 periph A Data bit 10 */
-+ AT91_PIOD 17 AT91_PERIPH_A AT91_PINCTRL_PULL_UP /* PD17 periph A Data bit 11 */
-+ AT91_PIOD 18 AT91_PERIPH_A AT91_PINCTRL_PULL_UP /* PD18 periph A Data bit 12 */
-+ AT91_PIOD 19 AT91_PERIPH_A AT91_PINCTRL_PULL_UP /* PD19 periph A Data bit 13 */
-+ AT91_PIOD 20 AT91_PERIPH_A AT91_PINCTRL_PULL_UP /* PD20 periph A Data bit 14 */
-+ AT91_PIOD 21 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>; /* PD21 periph A Data bit 15 */
-+ };
-+ };
-+
-+ mmc1 {
-+ pinctrl_mmc1_slot0_clk_cmd_dat0: mmc1_slot0_clk_cmd_dat0-0 {
-+ atmel,pins =
-+ <AT91_PIOA 13 AT91_PERIPH_B AT91_PINCTRL_NONE /* PA13 periph B */
-+ AT91_PIOA 12 AT91_PERIPH_B AT91_PINCTRL_PULL_UP /* PA12 periph B with pullup */
-+ AT91_PIOA 11 AT91_PERIPH_B AT91_PINCTRL_PULL_UP>; /* PA11 periph B with pullup */
-+ };
-+
-+ pinctrl_mmc1_slot0_dat1_3: mmc1_slot0_dat1_3-0 {
-+ atmel,pins =
-+ <AT91_PIOA 2 AT91_PERIPH_B AT91_PINCTRL_PULL_UP /* PA2 periph B with pullup */
-+ AT91_PIOA 3 AT91_PERIPH_B AT91_PINCTRL_PULL_UP /* PA3 periph B with pullup */
-+ AT91_PIOA 4 AT91_PERIPH_B AT91_PINCTRL_PULL_UP>; /* PA4 periph B with pullup */
-+ };
-+ };
-+ };
-+
-+ rtc@fffffeb0 {
-+ status = "okay";
-+ };
-+
-+ i2c0: i2c@f8010000 {
-+ compatible = "i2c-gpio";
-+ status = "okay";
-+
-+ id_eeprom@56 {
-+ compatible = "atmel,24c04";
-+ reg = <0x56>;
-+ pagesize = <16>;
-+ };
-+ board_temp@48 {
-+ compatible = "ti,tmp102";
-+ reg = <0x48>;
-+ /* tempsensor_alert line running to pin PC19 on processor
-+ set up an interrupt for this? */
-+ };
-+ };
-+
-+ i2c1: i2c@f8014000 {
-+ compatible = "i2c-gpio";
-+ status = "okay";
-+
-+ ap1_eeprom@50 {
-+ compatible = "atmel,24c04";
-+ reg = <0x50>;
-+ pagesize = <16>;
-+ };
-+ ap2_eeprom@52 {
-+ compatible = "atmel,24c04";
-+ reg = <0x52>;
-+ pagesize = <16>;
-+ };
-+ };
-+
-+ /* runs to Accessory Port 1 */
-+ spi0: spi@f0000000 {
-+ status = "okay";
-+ cs-gpios = <&pioA 4 0>, <&pioA 2 0>, <&pioA 3 0>, <&pioA 5 0>;
-+
-+ ap1-adc@0 {
-+ compatible = "mts-io-ap1-adc";
-+ spi-max-frequency = <20000000>;
-+ reg = <0>;
-+ };
-+ ap1-dout@1 {
-+ compatible = "mts-io-ap1-dout";
-+ spi-max-frequency = <1000000>;
-+ reg = <1>;
-+ };
-+ ap1-spi@2 {
-+ compatible = "spidev";
-+ spi-max-frequency = <2000000>;
-+ reg = <2>;
-+ };
-+ ap1-din@3 {
-+ compatible = "mts-io-ap1-din";
-+ spi-max-frequency = <1000000>;
-+ reg = <3>;
-+ };
-+ };
-+
-+ /* runs to Accessory Port 2 */
-+ spi1: spi@f0004000 {
-+ status = "okay";
-+
-+ cs-gpios = <&pioC 15 0>, <&pioC 16 0>, <&pioC 17 0>, <&pioC 18 0>;
-+
-+ ap2-adc@0 {
-+ compatible = "mts-io-ap2-adc";
-+ spi-max-frequency = <20000000>;
-+ reg = <0>;
-+ };
-+ ap2-dout@1 {
-+ compatible = "mts-io-ap2-dout";
-+ spi-max-frequency = <1000000>;
-+ reg = <1>;
-+ };
-+ ap2-spi@2 {
-+ compatible = "spidev";
-+ spi-max-frequency = <2000000>;
-+ reg = <2>;
-+ };
-+ ap2-din@3 {
-+ compatible = "mts-io-ap2-din";
-+ spi-max-frequency = <1000000>;
-+ reg = <3>;
-+ };
-+ };
-+ };
-+
-+ nand0: nand@40000000 {
-+ reg = < 0x40000000 0x10000000
-+ 0xffffe000 0x600 /* PMECC Registers */
-+ 0xffffe600 0x200 /* PMECC Error Location Registers */
-+ 0x00100000 0x100000 /* PMECC looup table in ROM code */
-+ >;
-+ atmel,pmecc-lookup-table-offset = <0x8000 0x10000>;
-+ gpios = < &pioC 31 GPIO_ACTIVE_HIGH
-+ &pioD 4 GPIO_ACTIVE_HIGH
-+ 0
-+ >;
-+ atmel,pmecc-cap = <4>;
-+ atmel,nand-has-dma;
-+
-+ nand@0 {
-+ label = "NANDFlash";
-+ reg = <0x0 0x10000000>;
-+ };
-+ at91bootstrap@0 {
-+ label = "at91bootstrap";
-+ reg = <0x0 0x40000>;
-+ };
-+ uboot@40000 {
-+ label = "u-Boot";
-+ reg = <0x40000 0x80000>;
-+ };
-+ ubootconfig0@c0000 {
-+ label = "u-Boot Config";
-+ reg = <0xc0000 0xa0000>;
-+ };
-+ ubootconfig1@160000 {
-+ label = "u-Boot Redundant Config";
-+ reg = <0x160000 0xa0000>;
-+ };
-+ uImage@200000 {
-+ label = "uImage";
-+ reg = <0x200000 0x600000>;
-+ };
-+ config0@800000 {
-+ label = "Config";
-+ reg = <0x800000 0x800000>;
-+ };
-+ config1@1000000 {
-+ label = "OEM Config";
-+ reg = <0x1000000 0x800000>;
-+ };
-+ rootfs@1800000 {
-+ label = "Rootfs";
-+ reg = <0x1800000 0xe800000>;
-+ };
-+ };
-+ };
-+
-+ leds {
-+ compatible = "gpio-leds";
-+
-+ pa24 {
-+ label = "led-status";
-+ gpios = <&pioA 24 GPIO_ACTIVE_LOW>;
-+ linux,default-trigger = "default-on";
-+ };
-+ pa25 {
-+ label = "led-a";
-+ gpios = <&pioA 25 GPIO_ACTIVE_LOW>;
-+ };
-+ pa26 {
-+ label = "led-b";
-+ gpios = <&pioA 26 GPIO_ACTIVE_LOW>;
-+ };
-+ pa27 {
-+ label = "led-c";
-+ gpios = <&pioA 27 GPIO_ACTIVE_LOW>;
-+ };
-+ pa28 {
-+ label = "led-d";
-+ gpios = <&pioA 28 GPIO_ACTIVE_LOW>;
-+ };
-+ };
-+
-+ /* GPS-PPS input on AP1 */
-+ pps {
-+ compatible = "pps-gpio";
-+ gpios = <&pioA 29 0>;
-+ capture-clear;
-+ };
-+
-+
-+ i2c@0 {
-+ status = "okay";
-+
-+ id_eeprom@56 {
-+ compatible = "atmel,24c04";
-+ reg = <0x56>;
-+ pagesize = <16>;
-+ };
-+ board_temp@48 {
-+ compatible = "ti,tmp102";
-+ reg = <0x48>;
-+ /* tempsensor_alert line running to pin PC19 on processor
-+ set up an interrupt for this? */
-+ };
-+ };
-+ i2c@1 {
-+ status = "okay";
-+
-+ ap1_eeprom@50 {
-+ compatible = "atmel,24c04";
-+ reg = <0x50>;
-+ pagesize = <16>;
-+ };
-+ ap2_eeprom@52 {
-+ compatible = "atmel,24c04";
-+ reg = <0x52>;
-+ pagesize = <16>;
-+ };
-+ };
-+};
-Index: linux-3.12.27/arch/arm/boot/dts/at91sam9x5cm.dtsi
-===================================================================
---- linux-3.12.27.orig/arch/arm/boot/dts/at91sam9x5cm.dtsi 2014-08-26 07:12:26.000000000 -0500
-+++ linux-3.12.27/arch/arm/boot/dts/at91sam9x5cm.dtsi 2015-01-13 13:58:20.766078428 -0600
-@@ -40,48 +40,8 @@
- atmel,has-pmecc; /* Enable PMECC */
- atmel,pmecc-cap = <2>;
- atmel,pmecc-sector-size = <512>;
-- nand-on-flash-bbt;
-+ /* nand-on-flash-bbt; */
- status = "okay";
--
-- at91bootstrap@0 {
-- label = "at91bootstrap";
-- reg = <0x0 0x40000>;
-- };
--
-- uboot@40000 {
-- label = "u-boot";
-- reg = <0x40000 0x80000>;
-- };
--
-- ubootenv@c0000 {
-- label = "U-Boot Env";
-- reg = <0xc0000 0x140000>;
-- };
--
-- kernel@200000 {
-- label = "kernel";
-- reg = <0x200000 0x600000>;
-- };
--
-- rootfs@800000 {
-- label = "rootfs";
-- reg = <0x800000 0x1f800000>;
-- };
-- };
-- };
--
-- leds {
-- compatible = "gpio-leds";
--
-- pb18 {
-- label = "pb18";
-- gpios = <&pioB 18 GPIO_ACTIVE_LOW>;
-- linux,default-trigger = "heartbeat";
-- };
--
-- pd21 {
-- label = "pd21";
-- gpios = <&pioD 21 GPIO_ACTIVE_HIGH>;
- };
- };
-
-@@ -93,5 +53,4 @@
- pinctrl-0 = <&pinctrl_1wire_cm>;
- status = "okay";
- };
--
- };
-Index: linux-3.12.27/arch/arm/boot/dts/at91sam9x5ek.dtsi
-===================================================================
---- linux-3.12.27.orig/arch/arm/boot/dts/at91sam9x5ek.dtsi 2014-08-26 07:12:26.000000000 -0500
-+++ linux-3.12.27/arch/arm/boot/dts/at91sam9x5ek.dtsi 2015-01-15 14:57:35.931862696 -0600
-@@ -24,23 +24,11 @@
- &pinctrl_mmc0_slot0_clk_cmd_dat0
- &pinctrl_mmc0_slot0_dat1_3>;
- status = "okay";
-+ /* external micro SD slot */
- slot@0 {
- reg = <0>;
- bus-width = <4>;
-- cd-gpios = <&pioD 15 GPIO_ACTIVE_HIGH>;
-- };
-- };
--
-- mmc1: mmc@f000c000 {
-- pinctrl-0 = <
-- &pinctrl_board_mmc1
-- &pinctrl_mmc1_slot0_clk_cmd_dat0
-- &pinctrl_mmc1_slot0_dat1_3>;
-- status = "okay";
-- slot@0 {
-- reg = <0>;
-- bus-width = <4>;
-- cd-gpios = <&pioD 14 GPIO_ACTIVE_HIGH>;
-+ cd-gpios = <&pioA 1 GPIO_ACTIVE_HIGH>;
- };
- };
-
-@@ -48,22 +36,13 @@
- status = "okay";
- };
-
-- usart0: serial@f801c000 {
-+ uart0: serial@f8040000 {
- status = "okay";
- };
-
- usb2: gadget@f803c000 {
-- atmel,vbus-gpio = <&pioB 16 GPIO_ACTIVE_HIGH>;
-- status = "okay";
-- };
--
-- i2c0: i2c@f8010000 {
-+ /* atmel,vbus-gpio = <&pioB 16 GPIO_ACTIVE_HIGH>; mtcdt: no vbus-gpio */
- status = "okay";
--
-- wm8731: wm8731@1a {
-- compatible = "wm8731";
-- reg = <0x1a>;
-- };
- };
-
- pinctrl@fffff400 {
-@@ -82,51 +61,24 @@
- };
- };
-
-- spi0: spi@f0000000 {
-- status = "okay";
-- cs-gpios = <&pioA 14 0>, <0>, <0>, <0>;
-- m25p80@0 {
-- compatible = "atmel,at25df321a";
-- spi-max-frequency = <50000000>;
-- reg = <0>;
-- };
-- };
--
- watchdog@fffffe40 {
- status = "okay";
- };
-
-- ssc0: ssc@f0010000 {
-- status = "okay";
-- };
- };
-
- usb0: ohci@00600000 {
- status = "okay";
- num-ports = <3>;
-- atmel,vbus-gpio = <0 /* &pioD 18 GPIO_ACTIVE_LOW *//* Activate to have access to port A */
-- &pioD 19 GPIO_ACTIVE_LOW
-- &pioD 20 GPIO_ACTIVE_LOW
-- >;
-+ //mtcdt: no vbus-gpio
-+ //atmel,vbus-gpio = <0 /* &pioD 18 GPIO_ACTIVE_LOW *//* Activate to have access to port A */
-+ // &pioD 19 GPIO_ACTIVE_LOW
-+ // &pioD 20 GPIO_ACTIVE_LOW
-+ // >;
- };
-
- usb1: ehci@00700000 {
- status = "okay";
- };
- };
--
-- sound {
-- compatible = "atmel,sam9x5-wm8731-audio";
--
-- atmel,model = "wm8731 @ AT91SAM9X5EK";
--
-- atmel,audio-routing =
-- "Headphone Jack", "RHPOUT",
-- "Headphone Jack", "LHPOUT",
-- "LLINEIN", "Line In Jack",
-- "RLINEIN", "Line In Jack";
--
-- atmel,ssc-controller = <&ssc0>;
-- atmel,audio-codec = <&wm8731>;
-- };
- };
-Index: linux-3.12.27/arch/arm/boot/dts/Makefile
-===================================================================
---- linux-3.12.27.orig/arch/arm/boot/dts/Makefile 2014-08-26 07:12:26.000000000 -0500
-+++ linux-3.12.27/arch/arm/boot/dts/Makefile 2015-01-13 13:58:20.766078428 -0600
-@@ -35,6 +35,7 @@
- dtb-$(CONFIG_ARCH_AT91) += at91sam9g35ek.dtb
- dtb-$(CONFIG_ARCH_AT91) += at91sam9x25ek.dtb
- dtb-$(CONFIG_ARCH_AT91) += at91sam9x35ek.dtb
-+dtb-$(CONFIG_ARCH_AT91) += mtcdt.dtb
- # sama5d3
- dtb-$(CONFIG_ARCH_AT91) += sama5d31ek.dtb
- dtb-$(CONFIG_ARCH_AT91) += sama5d33ek.dtb
generated by cgit v1.2.3 (git 2.25.1) at 2024-06-12 02:03:57 +0000