Merge branch 'test-split'

Pull in changes to move to support Yocto Thud

1 files changed, 0 insertions, 555 deletions

diff --git a/recipes-kernel/linux/linux-at91-4.9.87/mtcdt/linux-4.9-mtcdt-device-tree.patch b/recipes-kernel/linux/linux-at91-4.9.87/mtcdt/linux-4.9-mtcdt-device-tree.patch
deleted file mode 100644
index ddc5123..0000000
--- a/recipes-kernel/linux/linux-at91-4.9.87/mtcdt/linux-4.9-mtcdt-device-tree.patch
+++ /dev/null
@@ -1,555 +0,0 @@
-Index: linux-at91-4.9/arch/arm/boot/dts/mtcdt.dts
-===================================================================
-diff -aNru linux-at91-4.9.orig/arch/arm/boot/dts/mtcdt.dts linux-at91-4.9/arch/arm/boot/dts/mtcdt.dts
---- linux-at91-4.9.orig/arch/arm/boot/dts/mtcdt.dts	1969-12-31 18:00:00.000000000 -0600
-+++ linux-at91-4.9/arch/arm/boot/dts/mtcdt.dts	2019-04-24 17:01:26.112074133 -0500
-@@ -0,0 +1,287 @@
-+/*
-+ * DTS file for Multi-Tech Systems MTCDT Hardware
-+ */
-+
-+/dts-v1/;
-+#include "at91sam9g25.dtsi"
-+#include "at91sam9x5ek.dtsi"
-+
-+
-+/ {
-+    model = "Multi-Tech Systems MTCDT";
-+    compatible = "atmel,at91sam9g25ek", "atmel,at91sam9x5ek", "atmel,at91sam9x5", "atmel,at91sam9";
-+
-+    ahb {
-+	apb {
-+
-+
-+	    macb0: ethernet@f802c000 {
-+		phy-mode = "rmii";
-+		status = "okay";
-+	    };
-+
-+            pinctrl@fffff400 {
-+		mmc0 {
-+		    pinctrl_board_mmc0: mmc0-board {
-+			atmel,pins =
-+			  <AT91_PIOA 1 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>;  /* PA1 gpio SD card pin pull up and deglitch */
-+		   };
-+		};
-+		nand {
-+		    pinctrl_nand: nand-0 {
-+			atmel,pins =
-+			    <AT91_PIOD 0 AT91_PERIPH_A AT91_PINCTRL_PULL_UP	/* PD0 periph A Read Enable */
-+			    AT91_PIOD 1 AT91_PERIPH_A AT91_PINCTRL_PULL_UP	/* PD1 periph A Write Enable */
-+			    AT91_PIOD 2 AT91_PERIPH_A AT91_PINCTRL_PULL_UP	/* PD2 periph A Address Latch Enable */
-+			    AT91_PIOD 3 AT91_PERIPH_A AT91_PINCTRL_PULL_UP	/* PD3 periph A Command Latch Enable */
-+			    AT91_PIOD 4 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP	/* PD4 gpio Chip Enable pin pull_up */
-+			    AT91_PIOC 31 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP	/* PC31 gpio RDY/BUSY pin pull_up */
-+			    AT91_PIOD 6 AT91_PERIPH_A AT91_PINCTRL_PULL_UP	/* PD6 periph A Data bit 0 */
-+			    AT91_PIOD 7 AT91_PERIPH_A AT91_PINCTRL_PULL_UP	/* PD7 periph A Data bit 1 */
-+			    AT91_PIOD 8 AT91_PERIPH_A AT91_PINCTRL_PULL_UP	/* PD8 periph A Data bit 2 */
-+			    AT91_PIOD 9 AT91_PERIPH_A AT91_PINCTRL_PULL_UP	/* PD9 periph A Data bit 3 */
-+			    AT91_PIOD 10 AT91_PERIPH_A AT91_PINCTRL_PULL_UP	/* PD10 periph A Data bit 4 */
-+			    AT91_PIOD 11 AT91_PERIPH_A AT91_PINCTRL_PULL_UP	/* PD11 periph A Data bit 5 */
-+			    AT91_PIOD 12 AT91_PERIPH_A AT91_PINCTRL_PULL_UP	/* PD12 periph A Data bit 6 */
-+			    AT91_PIOD 13 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;	/* PD13 periph A Data bit 7 */
-+		    };
-+
-+		    /delete-node/ nand_16bits-0;
-+                };
-+                mts-io {
-+		     pinctrl_mts_io_out: mts_io-0 {
-+                      atmel,pins =
-+                          <AT91_PIOD 14 AT91_PERIPH_A AT91_PINCTRL_PULL_UP    /* PD14 WiFi BT reset */
-+                          AT91_PIOD 16 AT91_PERIPH_A AT91_PINCTRL_PULL_UP     /* PD16 Secure reset */
-+                          AT91_PIOD 17 AT91_PERIPH_A AT91_PINCTRL_PULL_UP     /* PD17 MTQ reset */
-+                          AT91_PIOD 18 AT91_PERIPH_A AT91_PINCTRL_PULL_UP     /* PD18 USB Hub reset */
-+                          AT91_PIOD 19 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;   /* PD19 GNSS Int */
-+                      output-high;
-+		    };
-+		    pinctrl_mts_io_in: mts_io-1 {
-+                      atmel,pins =
-+                          <AT91_PIOD 20 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;   /* PD20 WiFi_BT_LPMode Input */
-+		    };
-+		    pinctrl_mts_io_gnss: mts_io-2 {
-+                      atmel,pins =
-+                          <AT91_PIOD 15 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;   /* PD20 WiFi_BT_LPMode Input */
-+                      output-low;
-+		    };
-+               };
-+
-+		mmc1 {
-+		    pinctrl_mmc1_slot0_clk_cmd_dat0: mmc1_slot0_clk_cmd_dat0-0 {
-+			atmel,pins =
-+			    <AT91_PIOA 13 AT91_PERIPH_B AT91_PINCTRL_NONE	/* PA13 periph B */
-+			    AT91_PIOA 12 AT91_PERIPH_B AT91_PINCTRL_PULL_UP	/* PA12 periph B with pullup */
-+			    AT91_PIOA 11 AT91_PERIPH_B AT91_PINCTRL_PULL_UP>;	/* PA11 periph B with pullup */
-+		    };
-+
-+		    pinctrl_mmc1_slot0_dat1_3: mmc1_slot0_dat1_3-0 {
-+			atmel,pins =
-+			    <AT91_PIOA 2 AT91_PERIPH_B AT91_PINCTRL_PULL_UP	/* PA2 periph B with pullup */
-+			    AT91_PIOA 3 AT91_PERIPH_B AT91_PINCTRL_PULL_UP	/* PA3 periph B with pullup */
-+			    AT91_PIOA 4 AT91_PERIPH_B AT91_PINCTRL_PULL_UP>;	/* PA4 periph B with pullup */
-+		    };
-+
-+		    /delete-node/ mmc1-board;
-+		};
-+            };
-+
-+	    rtc@fffffeb0 {
-+		status = "okay";
-+	    };
-+
-+			dbgu: serial@fffff200 {
-+				status = "okay";
-+				atmel,use-dma-rx;
-+				atmel,use-dma-tx;
-+			};
-+
-+            /* runs to Accessory Port 1 */
-+	    spi0: spi@f0000000 {
-+		status = "okay";
-+		cs-gpios = <&pioA 4 0>, <&pioA 2 0>, <&pioA 3 0>, <&pioA 5 0>;
-+
-+		ap1-adc@0 {
-+		    compatible = "mts-io-ap1-adc";
-+		    spi-max-frequency = <20000000>;
-+		    reg = <0>;
-+		};
-+		ap1-dout@1 {
-+		    compatible = "mts-io-ap1-dout";
-+		    spi-max-frequency = <1000000>;
-+		    reg = <1>;
-+		};
-+		ap1-spi@2 {
-+		    compatible = "mts,mtac";
-+		    spi-max-frequency = <2000000>;
-+			reg = <2>;
-+		};
-+		ap1-din@3 {
-+		    compatible = "mts-io-ap1-din";
-+		    spi-max-frequency = <1000000>;
-+		    reg = <3>;
-+		};
-+		/delete-node/ m25p80@0;
-+	    };
-+
-+	    /* runs to Accessory Port 2 */
-+	    spi1: spi@f0004000 {
-+		status = "okay";
-+
-+		cs-gpios = <&pioC 15 0>, <&pioC 16 0>, <&pioC 17 0>, <&pioC 18 0>;
-+
-+		ap2-adc@0 {
-+		    compatible = "mts-io-ap2-adc";
-+		    spi-max-frequency = <20000000>;
-+		    reg = <0>;
-+		};
-+		ap2-dout@1 {
-+		    compatible = "mts-io-ap2-dout";
-+		    spi-max-frequency = <1000000>;
-+		    reg = <1>;
-+		};
-+		ap2-spi@2 {
-+		    compatible = "mts,mtac";
-+		    spi-max-frequency = <2000000>;
-+			reg = <2>;
-+		};
-+		ap2-din@3 {
-+		    compatible = "mts-io-ap2-din";
-+		    spi-max-frequency = <1000000>;
-+		    reg = <3>;
-+		};
-+	    };
-+        };
-+
-+	nand0: nand@40000000 {
-+	    reg = < 0x40000000 0x10000000
-+		    0xffffe000 0x600		/* PMECC Registers */
-+		    0xffffe600 0x200		/* PMECC Error Location Registers */
-+		    0x00100000 0x100000		/* PMECC looup table in ROM code  */
-+		  >;
-+	    atmel,pmecc-lookup-table-offset = <0x8000 0x10000>;
-+	    gpios = <	&pioC 31 GPIO_ACTIVE_HIGH
-+			&pioD 4 GPIO_ACTIVE_HIGH
-+			0
-+		    >;
-+	    atmel,pmecc-cap = <4>;
-+	    atmel,nand-has-dma;
-+
-+	    nand@0 {
-+		label = "NANDFlash";
-+		reg = <0x0 0x10000000>;
-+	    };
-+	    at91bootstrap@0 {
-+		label = "at91bootstrap";
-+		reg = <0x0 0x40000>;
-+	    };
-+	    uboot@40000 {
-+		label = "u-Boot";
-+		reg = <0x40000 0x80000>;
-+	    };
-+	    ubootconfig0@c0000 {
-+		label = "u-Boot Config";
-+		reg = <0xc0000 0xa0000>;
-+	    };
-+	    ubootconfig1@160000 {
-+		label = "u-Boot Redundant Config";
-+		reg = <0x160000 0xa0000>;
-+	    };
-+	    uImage@200000 {
-+		label = "uImage";
-+		reg = <0x200000 0x600000>;
-+	    };
-+	    config0@800000 {
-+		label = "Config";
-+		reg = <0x800000 0x800000>;
-+	    };
-+	    config1@1000000 {
-+		label = "OEM Config";
-+		reg = <0x1000000 0x800000>;
-+	    };
-+	    rootfs@1800000 {
-+		label = "Rootfs";
-+		reg = <0x1800000 0xe800000>;
-+	    };
-+	};
-+    };
-+
-+    leds {
-+            compatible = "gpio-leds";
-+
-+            pa24 {
-+                    label = "led-status";
-+                    gpios = <&pioA 24 GPIO_ACTIVE_LOW>;
-+                    linux,default-trigger = "default-on";
-+            };
-+            pa25 {
-+                    label = "led-a";
-+                    gpios = <&pioA 25 GPIO_ACTIVE_LOW>;
-+            };
-+            pa26 {
-+                    label = "led-b";
-+                    gpios = <&pioA 26 GPIO_ACTIVE_LOW>;
-+            };
-+            pa27 {
-+                    label = "led-c";
-+                    gpios = <&pioA 27 GPIO_ACTIVE_LOW>;
-+            };
-+            pa28 {
-+                    label = "led-d";
-+                    gpios = <&pioA 28 GPIO_ACTIVE_LOW>;
-+            };
-+    };
-+
-+    /* GPS-PPS input on AP1 */
-+    pps-0 {
-+            compatible = "pps-gpio";
-+            gpios = <&pioA 29 0>;
-+            capture-clear;
-+            status = "okay";
-+    };
-+
-+
-+    i2c-gpio-0 {
-+	status = "okay";
-+
-+	id_eeprom@56 {
-+	    compatible = "atmel,24c04";
-+	    reg = <0x56>;
-+	    pagesize = <16>;
-+            status = "okay";
-+	};
-+	board_temp@48 {
-+	    compatible = "ti,tmp102";
-+	    reg = <0x48>;
-+            status = "okay";
-+	    /* tempsensor_alert line running to pin PC19 on processor
-+	       set up an interrupt for this? */
-+	};
-+    };
-+    i2c-gpio-1 {
-+	status = "okay";
-+
-+	ap1_eeprom@50 {
-+	    compatible = "atmel,24c04";
-+	    reg = <0x50>;
-+	    pagesize = <16>;
-+            status = "okay";
-+	};
-+	ap2_eeprom@52 {
-+	    compatible = "atmel,24c04";
-+	    reg = <0x52>;
-+	    pagesize = <16>;
-+            status = "okay";
-+	};
-+    };
-+    mts-io-0 {
-+	status = "okay";
-+	compatible = "mts,mts-io";
-+	pinctrl-names = "default";
-+	pinctrl-0 = <&pinctrl_mts_io_out>;
-+	pinctrl-1 = <&pinctrl_mts_io_in>;
-+	pinctrl-2 = <&pinctrl_mts_io_gnss>;
-+    };
-+};
-Index: linux-4.9/arch/arm/boot/dts/at91sam9x5cm.dtsi
-===================================================================
-diff -aNru linux-4.9-orig/arch/arm/boot/dts/at91sam9x5cm.dtsi linux-4.9/arch/arm/boot/dts/at91sam9x5cm.dtsi
---- linux-4.9-orig/arch/arm/boot/dts/at91sam9x5cm.dtsi	2018-11-28 18:38:25.509563104 -0600
-+++ linux-4.9/arch/arm/boot/dts/at91sam9x5cm.dtsi	2018-11-28 18:39:16.213561602 -0600
-@@ -43,48 +43,8 @@
- 			atmel,has-pmecc;	/* Enable PMECC */
- 			atmel,pmecc-cap = <2>;
- 			atmel,pmecc-sector-size = <512>;
--			nand-on-flash-bbt;
-+			/* nand-on-flash-bbt; */
- 			status = "okay";
--
--			at91bootstrap@0 {
--				label = "at91bootstrap";
--				reg = <0x0 0x40000>;
--			};
--
--			uboot@40000 {
--				label = "u-boot";
--				reg = <0x40000 0x80000>;
--			};
--
--			ubootenv@c0000 {
--				label = "U-Boot Env";
--				reg = <0xc0000 0x140000>;
--			};
--
--			kernel@200000 {
--				label = "kernel";
--				reg = <0x200000 0x600000>;
--			};
--
--			rootfs@800000 {
--				label = "rootfs";
--				reg = <0x800000 0x1f800000>;
--			};
--		};
--	};
--
--	leds {
--		compatible = "gpio-leds";
--
--		pb18 {
--			label = "pb18";
--			gpios = <&pioB 18 GPIO_ACTIVE_LOW>;
--			linux,default-trigger = "heartbeat";
--		};
--
--		pd21 {
--			label = "pd21";
--			gpios = <&pioD 21 GPIO_ACTIVE_HIGH>;
- 		};
- 	};
- 
-@@ -96,5 +56,4 @@
- 		pinctrl-0 = <&pinctrl_1wire_cm>;
- 		status = "okay";
- 	};
--
- };
-Index: linux-4.9/arch/arm/boot/dts/at91sam9x5ek.dtsi
-===================================================================
-diff -aNru linux-4.9-orig/arch/arm/boot/dts/at91sam9x5ek.dtsi linux-4.9/arch/arm/boot/dts/at91sam9x5ek.dtsi
---- linux-4.9-orig/arch/arm/boot/dts/at91sam9x5ek.dtsi	2018-11-28 17:48:21.157652047 -0600
-+++ linux-4.9/arch/arm/boot/dts/at91sam9x5ek.dtsi	2018-11-28 17:49:54.793649275 -0600
-@@ -25,23 +25,11 @@
- 					&pinctrl_mmc0_slot0_clk_cmd_dat0
- 					&pinctrl_mmc0_slot0_dat1_3>;
- 				status = "okay";
-+                                /* external micro SD slot */
- 				slot@0 {
- 					reg = <0>;
- 					bus-width = <4>;
--					cd-gpios = <&pioD 15 GPIO_ACTIVE_HIGH>;
--				};
--			};
--
--			mmc1: mmc@f000c000 {
--				pinctrl-0 = <
--					&pinctrl_board_mmc1
--					&pinctrl_mmc1_slot0_clk_cmd_dat0
--					&pinctrl_mmc1_slot0_dat1_3>;
--				status = "okay";
--				slot@0 {
--					reg = <0>;
--					bus-width = <4>;
--					cd-gpios = <&pioD 14 GPIO_ACTIVE_HIGH>;
-+					cd-gpios = <&pioA 1 GPIO_ACTIVE_HIGH>;
- 				};
- 			};
- 
-@@ -49,7 +37,7 @@
- 				status = "okay";
- 			};
- 
--			usart0: serial@f801c000 {
-+			uart0: serial@f8040000 {
- 				atmel,use-dma-rx;
- 				atmel,use-dma-tx;
- 				status = "okay";
-@@ -58,25 +46,12 @@
- 			usb2: gadget@f803c000 {
- 				pinctrl-names = "default";
- 				pinctrl-0 = <&pinctrl_board_usb2>;
--				atmel,vbus-gpio = <&pioB 16 GPIO_ACTIVE_HIGH>;
--				status = "okay";
--			};
--
--			i2c0: i2c@f8010000 {
--				status = "okay";
--
--				wm8731: wm8731@1a {
--					compatible = "wm8731";
--					reg = <0x1a>;
--				};
--			};
--
--			adc0: adc@f804c000 {
--				atmel,adc-ts-wires = <4>;
--				atmel,adc-ts-pressure-threshold = <10000>;
-+				/* atmel,vbus-gpio = <&pioB 16 GPIO_ACTIVE_HIGH>;		mtcdt: no vbus-gpio */
- 				status = "okay";
- 			};
- 
-+                        /* A/D convertor is unusable on Conduit */
-+                        
- 			pinctrl@fffff400 {
- 				camera_sensor {
- 					pinctrl_pck0_as_isi_mck: pck0_as_isi_mck-0 {
-@@ -118,7 +93,7 @@
- 			};
- 
- 			spi0: spi@f0000000 {
--				status = "disabled";	/* conflict with mmc1 */
-+                                status = "okay";
- 				cs-gpios = <&pioA 14 0>, <0>, <0>, <0>;
- 				m25p80@0 {
- 					compatible = "atmel,at25df321a";
-@@ -131,37 +106,20 @@
- 				status = "okay";
- 			};
- 
--			ssc0: ssc@f0010000 {
--				status = "okay";
--			};
- 		};
- 
- 		usb0: ohci@00600000 {
- 			status = "okay";
- 			num-ports = <3>;
--			atmel,vbus-gpio = <0 /* &pioD 18 GPIO_ACTIVE_LOW *//* Activate to have access to port A */
--					   &pioD 19 GPIO_ACTIVE_LOW
--					   &pioD 20 GPIO_ACTIVE_LOW
--					  >;
-+			//mtcdt: no vbus-gpio
-+			// atmel,vbus-gpio = <0 /* &pioD 18 GPIO_ACTIVE_LOW *//* Activate to have access to port A */
-+			//		   &pioD 19 GPIO_ACTIVE_LOW
-+			//		   &pioD 20 GPIO_ACTIVE_LOW
-+			//		  >;
- 		};
- 
- 		usb1: ehci@00700000 {
- 			status = "okay";
- 		};
- 	};
--
--	sound {
--		compatible = "atmel,sam9x5-wm8731-audio";
--
--		atmel,model = "wm8731 @ AT91SAM9X5EK";
--
--		atmel,audio-routing =
--			"Headphone Jack", "RHPOUT",
--			"Headphone Jack", "LHPOUT",
--			"LLINEIN", "Line In Jack",
--			"RLINEIN", "Line In Jack";
--
--		atmel,ssc-controller = <&ssc0>;
--		atmel,audio-codec = <&wm8731>;
--	};
- };
-diff -aNru linux-4.9-orig/arch/arm/boot/dts/Makefile linux-4.9/arch/arm/boot/dts/Makefile
---- linux-4.9-orig/arch/arm/boot/dts/Makefile	2018-11-28 17:48:26.197651897 -0600
-+++ linux-4.9/arch/arm/boot/dts/Makefile	2018-11-28 17:49:26.441650114 -0600
-@@ -43,7 +43,8 @@
- 	at91sam9g25ek.dtb \
- 	at91sam9g35ek.dtb \
- 	at91sam9x25ek.dtb \
--	at91sam9x35ek.dtb
-+	at91sam9x35ek.dtb \
-+	mtcdt.dtb
- dtb-$(CONFIG_SOC_SAM_V7) += \
- 	at91-kizbox2.dtb \
- 	at91-sama5d2_ptc_ek.dtb \
-Index: linux-4.9/arch/arm/boot/dts/at91sam9x5.dtsi
-===================================================================
-diff -aNru linux-4.9-orig/arch/arm/boot/dts/at91sam9x5.dtsi linux-4.9/arch/arm/boot/dts/at91sam9x5.dtsi
---- linux-4.9-orig/arch/arm/boot/dts/at91sam9x5.dtsi	2018-11-28 17:20:48.149700984 -0600
-+++ linux-4.9/arch/arm/boot/dts/at91sam9x5.dtsi	2018-11-28 17:27:35.665688919 -0600
-@@ -32,9 +32,6 @@
- 		gpio3 = &pioD;
- 		tcb0 = &tcb0;
- 		tcb1 = &tcb1;
--		i2c0 = &i2c0;
--		i2c1 = &i2c1;
--		i2c2 = &i2c2;
- 		ssc0 = &ssc0;
- 		pwm0 = &pwm0;
- 	};
-@@ -963,50 +960,7 @@
- 				status = "disabled";
- 			};
- 
--			i2c0: i2c@f8010000 {
--				compatible = "atmel,at91sam9x5-i2c";
--				reg = <0xf8010000 0x100>;
--				interrupts = <9 IRQ_TYPE_LEVEL_HIGH 6>;
--				dmas = <&dma0 1 AT91_DMA_CFG_PER_ID(7)>,
--				       <&dma0 1 AT91_DMA_CFG_PER_ID(8)>;
--				dma-names = "tx", "rx";
--				#address-cells = <1>;
--				#size-cells = <0>;
--				pinctrl-names = "default";
--				pinctrl-0 = <&pinctrl_i2c0>;
--				clocks = <&twi0_clk>;
--				status = "disabled";
--			};
--
--			i2c1: i2c@f8014000 {
--				compatible = "atmel,at91sam9x5-i2c";
--				reg = <0xf8014000 0x100>;
--				interrupts = <10 IRQ_TYPE_LEVEL_HIGH 6>;
--				dmas = <&dma1 1 AT91_DMA_CFG_PER_ID(5)>,
--				       <&dma1 1 AT91_DMA_CFG_PER_ID(6)>;
--				dma-names = "tx", "rx";
--				#address-cells = <1>;
--				#size-cells = <0>;
--				pinctrl-names = "default";
--				pinctrl-0 = <&pinctrl_i2c1>;
--				clocks = <&twi1_clk>;
--				status = "disabled";
--			};
--
--			i2c2: i2c@f8018000 {
--				compatible = "atmel,at91sam9x5-i2c";
--				reg = <0xf8018000 0x100>;
--				interrupts = <11 IRQ_TYPE_LEVEL_HIGH 6>;
--				dmas = <&dma0 1 AT91_DMA_CFG_PER_ID(9)>,
--				       <&dma0 1 AT91_DMA_CFG_PER_ID(10)>;
--				dma-names = "tx", "rx";
--				#address-cells = <1>;
--				#size-cells = <0>;
--				pinctrl-names = "default";
--				pinctrl-0 = <&pinctrl_i2c2>;
--				clocks = <&twi2_clk>;
--				status = "disabled";
--			};
-+			/* /delete_node/ command does not work. */
- 
- 			uart0: serial@f8040000 {
- 				compatible = "atmel,at91sam9260-usart";