diff options
Diffstat (limited to 'recipes-bsp/u-boot/u-boot-2016.09.01/mtrv1.patch')
| -rw-r--r-- | recipes-bsp/u-boot/u-boot-2016.09.01/mtrv1.patch | 261 |
1 files changed, 261 insertions, 0 deletions
diff --git a/recipes-bsp/u-boot/u-boot-2016.09.01/mtrv1.patch b/recipes-bsp/u-boot/u-boot-2016.09.01/mtrv1.patch new file mode 100644 index 0000000..49cb435 --- /dev/null +++ b/recipes-bsp/u-boot/u-boot-2016.09.01/mtrv1.patch @@ -0,0 +1,261 @@ +diff --git a/board/atmel/at91sam9x5ek/at91sam9x5ek.c b/board/atmel/at91sam9x5ek/at91sam9x5ek.c +index b0d440d..5640cef 100644 +--- a/board/atmel/at91sam9x5ek/at91sam9x5ek.c ++++ b/board/atmel/at91sam9x5ek/at91sam9x5ek.c +@@ -44,7 +44,8 @@ static void at91sam9x5ek_nand_hw_init(void) + csa = readl(&matrix->ebicsa); + csa |= AT91_MATRIX_EBI_CS3A_SMC_SMARTMEDIA; + /* NAND flash on D16 */ +- csa |= AT91_MATRIX_NFD0_ON_D16; ++ /* MTR: nand flash is set up by bootstrap, so leave it alone here */ ++ /* csa |= AT91_MATRIX_NFD0_ON_D16; */ + + /* Configure IO drive */ + csa &= ~AT91_MATRIX_EBI_EBI_IOSR_NORMAL; +@@ -256,6 +257,9 @@ int board_early_init_f(void) + + int board_init(void) + { ++ /* Set Status LED High */ ++ at91_set_gpio_output(BOOT_STATUS_LED, 0); ++ + /* arch number of AT91SAM9X5EK-Board */ + gd->bd->bi_arch_number = MACH_TYPE_AT91SAM9X5EK; + +@@ -362,4 +366,61 @@ void mem_init(void) + /* DDRAM2 Controller initialize */ + ddr2_init(ATMEL_BASE_DDRSDRC, ATMEL_BASE_CS1, &ddr2); + } ++ + #endif ++ ++/* on-board EEPROM */ ++struct mts_id_eeprom_layout { ++ char vendor_id[32]; ++ char product_id[32]; ++ char device_id[32]; ++ char hw_version[32]; ++ uint8_t mac_addr[6]; ++ char imei[32]; ++ uint8_t capa[32]; ++ uint8_t mac_bluetooth[6]; ++ uint8_t mac_wifi[6]; ++ uint8_t reserved[302]; ++}; ++ ++int board_get_enetaddr(uchar *enetaddr) ++{ ++ struct mts_id_eeprom_layout eeprom_buffer = {0}; ++ ++ if (eeprom_read(CONFIG_SYS_I2C_EEPROM_ADDR, 0, &eeprom_buffer, sizeof(eeprom_buffer))) { ++ printf("EEPROM: read error\n"); ++ return 0; ++ } ++ ++ if (eeprom_buffer.vendor_id[0] == 0x00 || eeprom_buffer.vendor_id[0] == 0xFF) { ++ printf("EEPROM: uninitialized\n"); ++ return 0; ++ } ++ ++ printf("vendor-id: %s\n", eeprom_buffer.vendor_id); ++ printf("product-id: %s\n", eeprom_buffer.product_id); ++ printf("device-id: %s\n", eeprom_buffer.device_id); ++ printf("hw-version: %s\n", eeprom_buffer.hw_version); ++ printf("mac-addr: %02x:%02x:%02x:%02x:%02x:%02x\n", eeprom_buffer.mac_addr[0], ++ eeprom_buffer.mac_addr[1], ++ eeprom_buffer.mac_addr[2], ++ eeprom_buffer.mac_addr[3], ++ eeprom_buffer.mac_addr[4], ++ eeprom_buffer.mac_addr[5]); ++ ++ memcpy(enetaddr, eeprom_buffer.mac_addr, 6); ++ ++ return 1; ++} ++ ++int misc_init_r(void) ++{ ++ uchar enetaddr[6]; ++ ++ /* set MAC address from EEPROM if read successful */ ++ if (board_get_enetaddr(enetaddr)) { ++ eth_setenv_enetaddr("ethaddr", enetaddr); ++ } ++ ++ return 0; ++} +diff -Naru a/configs/at91sam9x5ek_nandflash_defconfig b/configs/at91sam9x5ek_nandflash_defconfig +--- a/configs/at91sam9x5ek_nandflash_defconfig 2019-02-13 11:21:57.000000000 -0600 ++++ b/configs/at91sam9x5ek_nandflash_defconfig 2019-02-13 11:27:11.463114488 -0600 +@@ -31,7 +31,6 @@ + CONFIG_CMD_NAND=y + CONFIG_CMD_BOOTZ=y + CONFIG_CMD_MII=y +-CONFIG_CMD_I2C=y + + # The config option CONFIG_SILENT_CONSOLE can be used to quiet messages + # on the console. If the option has been enabled, the output can be +diff --git a/include/configs/at91sam9x5ek.h b/include/configs/at91sam9x5ek.h +index 637c403..eff48d6 100644 +--- a/include/configs/at91sam9x5ek.h ++++ b/include/configs/at91sam9x5ek.h +@@ -9,8 +9,10 @@ + #ifndef __CONFIG_H__ + #define __CONFIG_H__ + ++#include <linux/kconfig.h> + #include <asm/hardware.h> + ++#define USE_MTR + #define CONFIG_SYS_TEXT_BASE 0x26f00000 + + /* ARM asynchronous clock */ +@@ -26,6 +28,8 @@ + #define CONFIG_BOARD_EARLY_INIT_F + #define CONFIG_DISPLAY_CPUINFO + ++#define CONFIG_MISC_INIT_R /* enable platform-dependent misc_init_r() */ ++ + /* general purpose I/O */ + #define CONFIG_ATMEL_LEGACY /* required until (g)pio is fixed */ + #define CONFIG_AT91_GPIO +@@ -36,6 +40,8 @@ + #define CONFIG_USART_ID ATMEL_ID_SYS + + /* LCD */ ++/* MTR has no LCD */ ++#if !defined(MTR) + #define CONFIG_LCD + #define LCD_BPP LCD_COLOR16 + #define LCD_OUTPUT_BPP 24 +@@ -46,7 +52,13 @@ + #define CONFIG_ATMEL_HLCD + #define CONFIG_ATMEL_LCD_RGB565 + #define CONFIG_SYS_CONSOLE_IS_IN_ENV ++#endif /* !defined(MTR) */ ++ ++/* check for keypress even if bootdelay is 0 */ ++#define CONFIG_ZERO_BOOTDELAY_CHECK + ++/*STATUS LED*/ ++#define BOOT_STATUS_LED AT91_PIN_PC21 + + /* + * BOOTP options +@@ -59,10 +71,7 @@ + /* no NOR flash */ + #define CONFIG_SYS_NO_FLASH + +-/* +- * Command line configuration. +- */ +-#define CONFIG_CMD_NAND ++#define CONFIG_SYS_I2C + + /* + * define CONFIG_USB_EHCI to enable USB Hi-Speed (aka 2.0) +@@ -94,13 +103,30 @@ + /* our CLE is AD22 */ + #define CONFIG_SYS_NAND_MASK_CLE (1 << 22) + #define CONFIG_SYS_NAND_ENABLE_PIN AT91_PIN_PD4 +-#define CONFIG_SYS_NAND_READY_PIN AT91_PIN_PD5 ++/* MTR nand ready is PC31 */ ++#define CONFIG_SYS_NAND_READY_PIN AT91_PIN_PC31 + + /* PMECC & PMERRLOC */ + #define CONFIG_ATMEL_NAND_HWECC 1 + #define CONFIG_ATMEL_NAND_HW_PMECC 1 +-#define CONFIG_PMECC_CAP 2 ++ ++/* MTR: 4-bit PMECC */ ++#define CONFIG_PMECC_CAP 4 + #define CONFIG_PMECC_SECTOR_SIZE 512 ++/* ++ * CONFIG_PMECC_INDEX_TABLE_OFFSET has been replaced by: ++ * ATMEL_PMECC_INDEX_OFFSET_512 and ++ * ATMEL_PMECC_INDEX_OFFSET_1024 ++ * ++ * Which as used depends on: ++ * host->pmecc_sector_size == 512 ++ * ++ * 2012.10: ++ * #define CONFIG_PMECC_INDEX_TABLE_OFFSET 0x8000 ++ * 2016.03 (at91sam9x5.h): ++ * 182:#define ATMEL_PMECC_INDEX_OFFSET_512 0x8000 ++ */ ++ + + #define CONFIG_CMD_NAND_TRIMFFS + +@@ -147,6 +173,23 @@ + #endif + #endif + ++#define CONFIG_SYS_I2C_SOFT ++#define CONFIG_SOFT_I2C ++#define CONFIG_SOFT_I2C_GPIO_SCL AT91_PIN_PA31 ++#define CONFIG_SOFT_I2C_GPIO_SDA AT91_PIN_PA30 ++#define CONFIG_SYS_I2C_SOFT_SPEED 50000 ++#define CONFIG_SYS_I2C_SPEED CONFIG_SYS_I2C_SOFT_SPEED ++/* Values from previous levels of Conduit U-Boot */ ++#define CONFIG_SYS_I2C_SLAVE 0xfe ++#define I2C_RXTX_LEN 128 ++ ++/* I2C eeprom support */ ++#define CONFIG_CMD_EEPROM ++#define CONFIG_SYS_I2C_EEPROM_ADDR 0x56 /* at24c04 */ ++#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address<---><------>*/ ++#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 ++ ++ + #define CONFIG_SYS_LOAD_ADDR 0x22000000 /* load address */ + + #define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE +@@ -156,11 +199,11 @@ + /* bootstrap + u-boot + env + linux in nandflash */ + #define CONFIG_ENV_IS_IN_NAND + #define CONFIG_ENV_OFFSET 0xc0000 +-#define CONFIG_ENV_OFFSET_REDUND 0x100000 ++#define CONFIG_ENV_OFFSET_REDUND 0x160000 + #define CONFIG_ENV_SIZE 0x20000 /* 1 sector = 128 kB */ +-#define CONFIG_BOOTCOMMAND "nand read " \ +- "0x22000000 0x200000 0x300000; " \ +- "bootm 0x22000000" ++/* MTR: read from env variables for boot */ ++#define CONFIG_BOOTCOMMAND "nboot.jffs2 ${loadaddr} 0 ${kernel_addr}; bootm ${loadaddr}" ++ + #elif defined(CONFIG_SYS_USE_SPIFLASH) + /* bootstrap + u-boot + env + linux in spi flash */ + #define CONFIG_ENV_IS_IN_SPI_FLASH +@@ -197,6 +240,9 @@ + "8M(bootstrap/uboot/kernel)ro,-(rootfs) " \ + "root=/dev/mmcblk0p2 " \ + "rw rootfstype=ext4 rootwait" ++#elif defined(USE_MTR) ++/* MTR uses jffs2 */ ++#define CONFIG_BOOTARGS "mem=128M console=ttyS0,115200 root=/dev/mtdblock8 ro rootfstype=jffs2" + #else + #define CONFIG_BOOTARGS \ + "console=ttyS0,115200 earlyprintk " \ +@@ -274,4 +320,21 @@ + + #endif + ++/* MTR defaults */ ++#define CONFIG_ENV_OVERWRITE 1 /* Allow Overwrite of serial# & ethaddr */ ++#define CONFIG_ETHADDR 00:08:00:87:00:02 ++#define CONFIG_IPADDR 192.168.2.1 ++#define CONFIG_NETMASK 255.255.255.0 ++#define CONFIG_SERVERIP 192.168.2.2 ++#define CONFIG_HOSTNAME AT91SAM9G25 ++#define CONFIG_LOADADDR 0x22000000 ++ ++/* MTR - enable watchdog */ ++#define CONFIG_AT91SAM9_WATCHDOG 1 ++#define CONFIG_HW_WATCHDOG 1 ++#define CONFIG_AT91_HW_WDT_TIMEOUT 16 ++#define CONFIG_EXTRA_ENV_SETTINGS \ ++ "kernel_addr=0x200000\0" \ ++ "" ++ + #endif |