add recipes for initial LoRa support for MTAC-LORA

2 files changed, 86 insertions, 0 deletions

diff --git a/recipes-connectivity/lora/lora-gateway/library.cfg b/recipes-connectivity/lora/lora-gateway/library.cfg
new file mode 100644
index 0000000..01b066d
--- /dev/null
+++ b/recipes-connectivity/lora/lora-gateway/library.cfg
@@ -0,0 +1,73 @@
+# That file will be included in the Makefile files that have hardware dependencies
+
+### SPI interface to the concentrator ###
+# Accepted values:
+#	native		Linux native SPI driver (/dev/spidev32766.0)
+#	ftdi		FTDI SPI-over-USB bridge using libmpsse/libftdi/libusb
+
+CFG_SPI= ftdi
+CFG_SPI_DEV = "/dev/spidev32766.2"
+
+### Concentrator chip ###
+# Accepted values:
+#	sx1301		Semtech SX1301 production chip
+#	fpga1301	FPGA containing the SX1301 IP
+
+CFG_CHIP= sx1301
+
+### Radio chip(s) ###
+# Accepted values:
+#	sx1257		Dual SX1257 transceivers, covering 860-1000 MHz
+#	sx1255		Dual SX1255 transceivers, covering 400-510 MHz
+
+CFG_RADIO= sx1257
+
+### RF band configuration ###
+# Used to configured frequency restrictions (eg. if a SAW filter is installed)
+# Accepted values:
+#	full		Full range supported by the radio(s)
+#	eu868		ETSI 868 (866) MHz band
+#	us915		FCC 915 MHz band
+#	cn470		China 470 MHz band
+#	eu433		ETSI 433 MHz band
+#	cn780		China 780 MHz band
+
+CFG_BAND= full
+
+### Board misc parameters & calibration ###
+# Used to configure misc board options.
+# RX RSSI indication and TX power are highly dependant on radio, band, filter
+# and RF front-ends, and must be calibrated for each new board design.
+# Available calibration parameters:
+#	dev_nano_868		FPGA-based nano-concentrator, with 868 MHz SAW filter
+#	ref_1301_868		SX1301 reference board with SX1257 radios, 868 MHz filters
+#	ref_1301_433		SX1301 reference board with SX1255 radios, 433 MHz filters
+#	kerlink_868			Kerlink LoRa 868MHz gateway
+#	kerlink_433			Kerlink LoRa 433MHz gateway
+#	cisco_433			Cisco LoRa 433MHz gateway
+#	cisco_470			Cisco LoRa 470MHz gateway
+#	cisco_780			Cisco LoRa 780MHz gateway
+# Keep empty for no calibration parameters (neutral values will be used).
+
+# MTAC-LORA 900MHz
+CFG_BRD= mtaclora
+
+### Network Type ###
+# Accepted values:
+#	private			Default
+#	lora_mac		Only compliant with devices running LoRa MAC
+
+CFG_NET= private
+
+### Debug options ###
+# Set the DEBUG_* to 1 to activate debug mode in individual modules.
+# Warning: that makes the module *very verbose*, do not use for production
+
+DEBUG_AUX= 0
+DEBUG_SPI= 0
+DEBUG_REG= 0
+# jjg - turning this on is useful to get HAL-related error messages that 
+# don't print out otherwise.  It doesn't seem to add that much printing
+# under normal operation.
+DEBUG_HAL= 1
+DEBUG_GPS= 0
diff --git a/recipes-connectivity/lora/lora-gateway/lora-gateway-debug.patch b/recipes-connectivity/lora/lora-gateway/lora-gateway-debug.patch
new file mode 100644
index 0000000..dba4392
--- /dev/null
+++ b/recipes-connectivity/lora/lora-gateway/lora-gateway-debug.patch
@@ -0,0 +1,13 @@
+Index: git/libloragw/src/loragw_hal.c
+===================================================================
+--- git.orig/libloragw/src/loragw_hal.c	2014-12-16 16:07:20.812506157 -0600
++++ git/libloragw/src/loragw_hal.c	2014-12-16 16:18:34.427454833 -0600
+@@ -1626,6 +1626,8 @@
+ 			break;
+ 		}
+ 	}
++
++	DEBUG_PRINTF("DEBUG: Tx pow_index %d, rf_power %d\n", pow_index, tx_pow_table[pow_index].rf_power);
+ 	
+ 	/* loading TX imbalance correction */
+ 	target_mix_gain = tx_pow_table[pow_index].mix_gain;