cdp-io-controller.git - I/O control module for OCG

Age	Commit message (Collapse)	Author	Files
2013-05-01	flip mtr status led initial value	Mike Fiore	1

2013-05-01	flip output value of status led for mtr2, should be on at startup	Mike Fiore	1

2013-04-24	bump driver version to 0.6.2v0.6.2	Mike Fiore	1

2013-04-24	product info: update sysfs script	Mike Fiore	1

2013-04-24	product info: add newlines after mac addresses, change -mac to mac- for ↵	Mike Fiore	1
	consistency
2013-04-24	added attributes wifi-mac, eth-mac, imei, vendor-id to machine types	Mike Fiore	1

2013-04-22	bump driver versionv0.6.1	Mike Fiore	1

2013-04-22	add device info to sysfs	Mike Fiore	1

2013-03-26	set reset pins active_lowv0.6.0	Jesse Gilles	1

2013-03-08	Merge branch 'master' of ssh://git.multitech.net/cdp-io-controller	Michael Fiore	1

2013-03-08	updated usage in mts-io-sysfs	Michael Fiore	1

2013-03-06	allow pins with empty attr_name, require name only	Jesse Gilles	1

2013-03-01	add led-a to led-f for MTOCGD3	Jesse Gilles	1

2013-02-28	more code clean up, rename platform to "mts-io", add mtocgd3 hardware	Jesse Gilles	3
	* add active_low to gpio struct, remove inverted gpio funcs * rename platform to "mts-io", add symlink to "mtcdp" for compatbility * add MTOCGD3 hardware
2013-02-25	code cleanup and re-org	Jesse Gilles	2

2013-02-19	Makefile: update clean	Jesse Gilles	1

2013-02-19	add open drain pin type and set multi-drive	Jesse Gilles	1

2013-01-14	read hw_version for MTR, MTR2, log detected board config	Jesse Gilles	2
	* allows for different product-id as long as hw-version is right (MTR3)
2012-11-08	add mtr2 rev A support	Jesse Gilles	1
	* added wifi led * rsersrc is removed * new serial_mode pins, rs4xx_term_res pin * bt-enable pin changed
2012-10-03	add extserial-ri for MTR RevA, rename EN4 to MTR2	Jesse Gilles	2

2012-08-22	fix previous commit	Jesse Gilles	1

2012-08-22	update logging for bluetooth/wifi	Jesse Gilles	1

2012-08-22	add bluetooth, wifi flags and mac addresses	Jesse Gilles	1

2012-08-02	added radio-reset routine for telit module	Jesse Gilles	1

2012-07-27	add open collector pin type, MTR radio reset/init support, fix minor bug	Jesse Gilles	1

2012-07-25	add mtr board support	Jesse Gilles	2

2012-06-21	add led-status for EN4	Jesse Gilles	1

2012-06-08	en4: set bt-enabled, wlan-enabled low on load	Jesse Gilles	1
	* fixes wl1271 init, both pins need to be low before enabling either wifi or bluetooth
2012-05-14	gpio_pin_by_attr_name: allow empty strings	Jesse Gilles	1

2012-05-14	en4: add rs422-term-res, rs485-term-res pins	Jesse Gilles	1

2012-05-09	add eth-switch-enabled for en4, only drive output when low	Jesse Gilles	1
	* Only drive the output pin when set low (reset active), else leave pin floating since it has an external pull up. If instead the output pin is driven high, the ethernet switch locks up after a soft reboot.
2012-05-08	added serial-mode for en4	Jesse Gilles	1

2012-05-07	en4: add reset, reset-monitor	Jesse Gilles	1

2012-05-07	add en4 support, reduce some duplication	Jesse Gilles	2

2012-01-05	add daughter card reset (ndc-reset)	Jesse Gilles	1

2011-10-03	add locking on adc readv0.5.1	Jesse Gilles	1

2011-09-30	read one adc at a time	Jesse Gilles	1

2011-09-30	Defined mts_product_id variable to store current product type on driver ↵	Thanh Tran	2
	init. All subsequence product type checkings are now done using this variable.
2011-09-30	1. Used strncmp() to compare only the product name portion of product_ID.	Thanh Tran	1
	2. GPOx logic levels were wrong, corrections were made to match the stand-alone CDP box. 3. Configured GPIO11 and GPIO12 to be open-drain. 4. Set driver version to v0.5.1
2011-09-27	rename MT100ECDP to MT100EOCG	Jesse Gilles	2

2011-09-14	Making IO signals logic the same as the stand-alone CDP box.v0.5.0	Thanh Tran	1

2011-09-01	Modified "Usage:" by determine which platform is currently running and ↵	Thanh Tran	1
	display "Usage:" accordingly.
2011-08-22	Added control of external DTR and external DCD signals for MT100ECDP.	Thanh Tran	1

2011-08-05	Added support for the embedded CDP module called (MT100ECDP).	Thanh Tran	2

2010-12-30	make TXD1 an input (fixes external serial RX data), bump version to v0.4.1v0.4.1	Jesse Gilles	1

2010-12-17	fix log typosv0.4.0	Jesse Gilles	1

2010-12-17	fix reading of dout pin state (invert to match output state)	Jesse Gilles	1

2010-12-17	invert dout state: 0 drives output to ground, 1 is open/floating	Jesse Gilles	1

2010-09-28	add usb host power switch debug gpios	James Maki	1

2010-09-17	make max_speed_hz configurable as module params for the spi devices.	James Maki	1