Age | Commit message (Expand) | Author | Files |
2012-06-21 | add led-status for EN4 | Jesse Gilles | 1 |
2012-06-08 | en4: set bt-enabled, wlan-enabled low on load | Jesse Gilles | 1 |
2012-05-14 | gpio_pin_by_attr_name: allow empty strings | Jesse Gilles | 1 |
2012-05-14 | en4: add rs422-term-res, rs485-term-res pins | Jesse Gilles | 1 |
2012-05-09 | add eth-switch-enabled for en4, only drive output when low | Jesse Gilles | 1 |
2012-05-08 | added serial-mode for en4 | Jesse Gilles | 1 |
2012-05-07 | en4: add reset, reset-monitor | Jesse Gilles | 1 |
2012-05-07 | add en4 support, reduce some duplication | Jesse Gilles | 2 |
2012-01-05 | add daughter card reset (ndc-reset) | Jesse Gilles | 1 |
2011-10-03 | add locking on adc readv0.5.1 | Jesse Gilles | 1 |
2011-09-30 | read one adc at a time | Jesse Gilles | 1 |
2011-09-30 | Defined mts_product_id variable to store current product type on driver init.... | Thanh Tran | 2 |
2011-09-30 | 1. Used strncmp() to compare only the product name portion of product_ID. | Thanh Tran | 1 |
2011-09-27 | rename MT100ECDP to MT100EOCG | Jesse Gilles | 2 |
2011-09-14 | Making IO signals logic the same as the stand-alone CDP box.v0.5.0 | Thanh Tran | 1 |
2011-09-01 | Modified "Usage:" by determine which platform is currently running and displa... | Thanh Tran | 1 |
2011-08-22 | Added control of external DTR and external DCD signals for MT100ECDP. | Thanh Tran | 1 |
2011-08-05 | Added support for the embedded CDP module called (MT100ECDP). | Thanh Tran | 2 |
2010-12-30 | make TXD1 an input (fixes external serial RX data), bump version to v0.4.1v0.4.1 | Jesse Gilles | 1 |
2010-12-17 | fix log typosv0.4.0 | Jesse Gilles | 1 |
2010-12-17 | fix reading of dout pin state (invert to match output state) | Jesse Gilles | 1 |
2010-12-17 | invert dout state: 0 drives output to ground, 1 is open/floating | Jesse Gilles | 1 |
2010-09-28 | add usb host power switch debug gpios | James Maki | 1 |
2010-09-17 | make max_speed_hz configurable as module params for the spi devices. | James Maki | 1 |
2010-09-16 | the spi din should be SPI_CPOL | James Maki | 1 |
2010-09-13 | add dout, din, adc, led-dtr to help display | James Maki | 1 |
2010-09-10 | turn off DEBUG | James Maki | 1 |
2010-09-10 | clean up formatting | James Maki | 1 |
2010-09-09 | check the capabilities array instead of checking against the hw_version | James Maki | 1 |
2010-09-09 | copy the eeprom from the platform file instead of overwriting it. | James Maki | 1 |
2010-09-09 | cleanup eeprom related stuff. | James Maki | 3 |
2010-09-09 | update for MTCDP-1.0 | James Maki | 2 |
2010-07-27 | add extserial-dtrv0.3.0 | Jesse Gilles | 3 |
2010-07-27 | increase radio reset pulse to 250ms | Jesse Gilles | 1 |
2010-05-17 | add extserial-dsr to help | James Maki | 1 |
2010-05-05 | turn off DEBUGv0.2.0 | James Maki | 1 |
2010-05-04 | fix an oops! | James Maki | 1 |
2010-05-03 | fix broken sysfs test | James Maki | 1 |
2010-05-03 | update comments and names | James Maki | 1 |
2010-05-03 | register devices with spi controller | James Maki | 3 |
2010-04-29 | Add GPLv2 | James Maki | 2 |
2010-04-27 | rename platform to mtcdp | Jesse Gilles | 2 |
2010-04-23 | initial commit | James Maki | 6 |